Table of Contents
Advertisement
[[S] CAMERA SETTING]
Item
[SHOOTING MODE]
[DETAIL]
[2D LPF]
[GAMMA]
[TEST SAW]
[FLARE]
[H-F COMPE.]
@
NOTE
t All [[S] CAMERA SETTING] items are targets of [PAINT([S]SELECT)] in the main menu → [FILE] → [SETUP DATA SELECT].
[VF]
These items are shown when selecting contents to show in the viewfinder screen.
These menu items cannot be set when the thumbnail screen is displayed.
[VF DISPLAY]
Item
[VF/LCD CHAR]
[VF MODE]
[VF COLOR]
[DISP CONDITION]
[DISP MODE]
Chapter 6 Menu Operations — Menu list
Selects the shooting mode according to the shooting environment.
[NORMAL]: Selects normal sensitivity. (Appropriate when shooting in normal brightness.)
[HIGH SENS.]: Selects high-sensitivity. (Appropriate when shooting in a dark environment.)
[H.SENS.] is displayed on the viewfinder screen.
f Factory setting: [NORMAL]
If [NORMAL] is selected, [−6dB] cannot be assigned to <LOW>/<MID>/<HIGH> on the <GAIN> switch.
If changed from [HIGH SENS.] to [NORMAL], the following setting values also change.
f When [−6dB] is set in the main menu → [PAINT] → [LOW SETTING] → [[S] MASTER GAIN], it is
changed to [−3dB].
f When [−6dB] is set in the main menu → [PAINT] → [MID SETTING] → [[S] MASTER GAIN], it is
changed to [−3dB].
f When [−6dB] is set in the main menu → [PAINT] → [HIGH SETTING] → [[S] MASTER GAIN], it is
changed to [−3dB].
Switches the detail signal [ON]/[OFF].
[ON], [OFF]
f Factory setting: [ON]
Sets a 2D low-pass filter to reduce cross colors.
[ON]: Reduces cross colors.
[OFF]: Does not reduce cross colors.
f Factory setting: [OFF]
This item is displayed when in SD mode (480/59.94i and 576/50i).
Enables/disables gamma correction.
[ON], [OFF]
f Factory setting: [ON]
Enables/disables the test signal.
[ON], [OFF]
f Factory setting: [OFF]
Enables/disables flare correction.
[ON], [OFF]
f Factory setting: [ON]
Enables/disables aperture correction.
[ON], [OFF]
f Factory setting: [ON]
Selects whether to display a character on the image of the LCD monitor and viewfinder.
[ON]: Displays characters on both the viewfinder and LCD monitor.
[VF-OFF]: Does not superimpose on the viewfinder, and displays on the LCD monitor.
[LCD-OFF]: Does not superimpose on the LCD monitor, and displays on the viewfinder.
f Factory setting: [ON]
Selects a viewfinder image.
[MEM]: In playback mode, these are playback images.
[CAM]: Always camera images.
f Factory setting: [MEM]
This item is enabled when [CAM] is set in the main menu → [SYSTEM] → [SYSTEM MODE] → [REC
SIGNAL]. When [SDI] is set, playback images are output in the playback mode regardless of this setting.
Selects whether to display viewfinder images in color or in black and white.
[ON]: Displays in color.
[OFF]: Displays in black and white (playback images, thumbnail screens and menu displays remain in
color).
f Factory setting: [ON]
Selects the status display method.
[NORMAL]: Status is always displayed.
[HOLD]: Normally, status is not displayed. Push the <MARKER SEL>/<MODE CHECK/MENU CANCEL>
switch towards the <MCK/MCL> side to display when the mode check screen is displayed.
f Factory setting: [NORMAL]
Shows/hides camera warning/notification displayed in the center of the viewfinder.
For details, refer to "Display modes and setting changes/adjustment result messages" (page 113).
[1], [2], [3]
f Factory setting: [3]
– 164 –
Description of settings
Description of settings
Advertisement
Table of Contents
