Table of Contents
Advertisement
f Press and hold the <REC> button for at least two seconds during recording, to end recording. (When operating while recording.)
These operations end linking of clips. [END 1-CLIP] is displayed in the viewfinder screen, and a new clip starts from the subsequent recording.
@
NOTE
t In the following cases, the camera finishes clip linking and records as a new clip.
- When the power is turned off
- When a P2 card recorded immediately before is removed
- When the P2 card is formatted or the clips are deleted (when the original linked clip no longer exists)
- When the recording slot (P2 (slots 1, 2) and microP2 (slots 3, 4)) is switched using the menu or the <USER> button
t When the menu or thumbnails are displayed, clip linking cannot be ended even if you press the <STOP> button.
t Clip linking cannot be ended even if the <STOP> button or the <REC> button on the extension control unit (AG-EC4G) is pressed.
t For details on system modes in which the one-clip recording function can be used, refer to the table in "System modes and recording functions"
(page 79).
t Clip linking cannot be ended even if you press the <USER> button to which [REC SW] is assigned.
Ending one-clip recording mode
Set [OFF] in the main menu → [REC/PB] → [REC FUNCTION] → [ONE CLIP REC].
Cueing up linked parts of clips
Each time recording starts, a text memo is automatically added to the recording start position so that you can cue up when playing back. You can also
check the thumbnail of its position.
To add a text memo automatically to a recording start position, set [ON] in the main menu → [REC/PB] → [REC/PB SETUP] → [START TEXT MEMO].
To view or play back the point of the added text memo, select [TEXT MEMO CLIPS] in the main menu → [CLIP] → [REPOSITION] and place the cursor
on the target clip.
For details, refer to "Playing back from the text memo position" (page 135).
Also, to cue up the text memo position when playing back, set [CLIP&TEXT MEMO] in the main menu → [REC/PB] → [REC/PB SETUP] → [SEEK POS
SEL]. Press the <FF/)> button or the <%/REW> button while playback is paused.
Proxy recording in one-clip recording mode
You can carry out proxy recording in one-clip recording mode.
The proxy data also can be combined as the same type of linked clip so that you can handle it as a single clip with the P2 Viewer Plus, etc.
However, when recording proxy data on an SD memory card, be careful of the following points.
f When you remove the SD memory card and replace it while continuously making clip links, proxy recording will not take place on the SD memory card
until the subsequent clips are linked. Use after making sure that there is sufficient available space and number of files (maximum of 1000 clips can be
recorded).
f When continuing proxy recording after replacing the SD memory card part-way through, carry out the following operation. Press the <STOP> button
for approximately two seconds to finish linking, and start recording as a new clip.
f The proxy data on the SD memory card that was discontinued during recording is not recognized as proxy data for the clip recorded on the P2 card
and will remain incomplete.
When using one-clip recording mode
f When interval recording, one-shot recording, or loop recording is selected, it does not operate. Also, it does not operate when [SDI] is set in the main
menu → [SYSTEM] → [SYSTEM MODE] → [REC SIGNAL].
f While continuing clip linking, menu operations are subject to the following restrictions. Perform these operations after pressing and holding the
<STOP> button for approx. two seconds to end clip linking.
- Some items of [REC FUNCTION] in the main menu → [REC/PB] cannot be changed.
- Some items of [SYSTEM MODE] in the main menu → [SYSTEM] cannot be changed.
- Some items of [FILE] in the main menu cannot be operated.
- The main menu → [CLIP] → [COPY] does not operate.
- [ON] cannot be set in the main menu → [I/F SETUP] → [USB/LAN] → [USB MODE].
f In order to make it possible to link clips in the next recording, the processing time required to end recording may take slightly longer than standard
recording.
f When playing back, fade processing for discontinuous audio is not performed at linking points within a clip.
f When editing a clip with a large number of links using nonlinear editing software, etc., the software may not operate properly depending on the type of
software.
Refer to the support desk at the following website for the latest information on software whose operability has been confirmed.
https://pro-av.panasonic.net/
Chapter 4 Shooting — Special recording functions
– 76 –
Advertisement
Table of Contents
