[Rec/Pb] - Panasonic AJ-PX5100G Operating Instructions Manual

[REC/PB]

These are various types of setting items when performing camera recording and playback.
[REC FUNCTION]
Item
[RECORDING]
[HOLD]
[REC TIME]
[PAUSE TIME]
[START DELAY]
[ONE CLIP REC]
[PRE REC]
[PRE REC TIME]
[SIMUL REC]
Chapter 6 Menu Operations — Menu list
Select the recording format.
[NORMAL]: Performs standard recording.
[INTERVAL]: Performs interval recording.
[ONE SHOT]: Performs one-shot recording.
[LOOP]: Performs loop recording.
f Factory setting: [NORMAL]
Only [NORMAL] can be selected in the following cases:
f When the main menu → [SYSTEM] → [SYSTEM MODE] → [REC SIGNAL] is set to [SDI]
f When the main menu → [SYSTEM] → [SYSTEM MODE] → [REC FORMAT] is set to [AVC-G50] or
[AVC-G25]
Selects whether to hold [RECORDING] settings.
[ON]: Holds the settings.
[OFF]: Does not hold the settings. It will always be [NORMAL] the next time that power is turned on.
f Factory setting: [OFF]
Sets the recording time (one cut) when [INTERVAL] or [ONE SHOT] is selected in [RECORDING].
59.94 Hz: [00s01frm]...[59s29frm]
50 Hz: [00s01frm]...[59s24frm]
f Factory setting: [00s01frm]
Sets the time to pause recording when [INTERVAL] is selected in [RECORDING].
59.94 Hz: [00h00min00s01frm]...[23h59min59s29frm]
50 Hz: [00h00min00s01frm]...[23h59min59s24frm]
When [NTSC] or [NTSC (J)] is selected in the setting of the region of use ([OPTION MENU] → [AREA
SETTING] → [AREA SELECT]):
f Factory setting: [00h04min59s29frm]
When [PAL] is selected in the setting of the region of use ([OPTION MENU] → [AREA SETTING] → [AREA
SELECT]):
f Factory setting: [00h04min59s24frm]
Sets the time before start recording after the <REC> button is pressed when [INTERVAL] is selected in
[RECORDING].
[0s]...[10s]
f Factory setting: [0s]
Selects the one-clip recording mode.
[ON]: Operates in one-clip recording mode.
[OFF]: Does not operate in one-clip recording mode.
f Factory setting: [OFF]
This item cannot be changed in the following cases:
f When the main menu → [SYSTEM] → [SYSTEM MODE] → [REC SIGNAL] is set to [SDI]
f When the main menu → [REC/PB] → [REC FUNCTION] → [SIMUL REC] is set to [ON]
f When the main menu → [REC/PB] → [REC FUNCTION] → [RECORDING] is set to an item other than
[NORMAL]
Selects whether to perform pre-recording. Sets the time to perform continuous pre-recording when [ON] is
selected.
[ON]: Performs pre-recording.
[OFF]: Does not perform pre-recording.
f Factory setting: [OFF]
[ON] cannot be selected in the following cases:
f When the main menu → [SYSTEM] → [SYSTEM MODE] → [REC SIGNAL] is set to [SDI]
f When the main menu → [REC/PB] → [REC FUNCTION] → [RECORDING] is set to an item other than
[NORMAL]
Configures pre-recording settings.
Sets a time that can be recorded by counting backward from the time that the <REC> button is pushed.
Up to a maximum of 15 seconds can be selected in DVCPRO and DV modes, and up to 8 seconds in
other modes.
HD, DVCPRO50: [0s]...[8s]
f Factory setting: [8s]
DV, DVCPRO: [0s]...[15s]
f Factory setting: [8s]
Pre-recording setup takes up to 3 seconds in the following cases.
f When the main menu → [SYSTEM] → [SYSTEM MODE] → [LINE&FREQ] and [REC FORMAT] are set
to 1080P mode and [AVC-I100] respectively
Selects whether to perform simultaneous recording.
[ON]: Operates in simultaneous recording mode.
[OFF]: Does not operate in simultaneous recording mode.
f Factory setting: [OFF]
This item cannot be changed in the following cases:
f When the main menu → [REC/PB] → [REC FUNCTION] → [RECORDING] is set to an item other than
[NORMAL]
f When the main menu → [REC/PB] → [REC FUNCTION] → [ONE CLIP REC] is set to [ON]
f When main menu → [REC/PB] → [DUAL CODEC SETUP] → [CODEC USAGE] is set to [PROXY
REC(P2)] or [PROXY REC(P2&SD)]
– 178 –
Description of settings