Table of Contents
Advertisement
@
NOTE
t Thumbnail operations and menu operations on thumbnail operation section are not possible while the <TCG> switch is set to <SET>.
t To confirm VITC UB, press the <HOLD> switch to display [VTCG] on the status display.
Retention of user bits in memory
User bit settings are automatically recorded and are retained even if the power is turned off.
Frame rate information recorded on user bits
Saving the frame rate values for the image information shot/saved according to the frame rate set in main menu → [SYSTEM] → [SYSTEM MODE] to
user bits allows you to use the editor (personal computer editing software).
Information is always saved in VITC UB.
In addition, selecting [FRAME RATE] in main menu → [REC/PB] → [TC/UB] → [UBG MODE] saves the information in user bits (LTC UB) as well. In
playback of clips recorded in native format, the same values as the frame rate information obtained by playing back recorded user bits are also output
as HD SDI output signals or user bits of TC output from the <TC OUT> terminal.
Frame rate information
The relationship between frame rates, image pull-down, and time codes/user bits is as follows.
Verification information on the right-hand six digits
Setting the time code
1
Set the <DISPLAY> switch to <TC>.
2
Set the <TCG> switch to <SET>.
3
Set [DF] or [NDF] in the main menu → [REC/PB] → [TC/UB] → [DF MODE].
For details, refer to "Setting menu basic operations" (page 153).
f Set [DF] to advance the time code in the drop frame mode, and set [NDF] to advance it in the non-drop frame mode. However, note that the time
code runs by [NDF] at all times in the 24PN mode.
4
Set the time code by the cursor buttons.
f Screen display
- I: The digit to be set (flashing) moves to the right.
- Y: The digit to be set (flashing) moves to the left.
- `: The value of the digit to set (flashing) is incremented by one.
- {: The value of the digit to set (flashing) is decremented by one.
5
Switch by the <TCG> switch.
To advance the time code by free run, switch to <F-RUN>, and to advance by recording run, switch to <R-RUN>.
Settable time code range
For 59.94 Hz (except for 24PN)
For 24PN
For 50 Hz:
@
NOTE
t Switching of [DF] and [NDF] is enabled when the system frequency of the camera is set to 59.94 Hz.
t When using with 24PN, the time code setting is adjusted in 4-frame units.
With 720/30PN and 720/25PN, the time code is adjusted to even numbers. Also, with 24PN, the time code cannot be set during recording.
Chapter 4 Shooting — Setting the time data
Fixed values
Sequence No.
24P: 0 - 4
Other than the above: Fixed to F
00:00:00:00 - 23:59:59:29
00:00:00:00 - 23:59:59:23
00:00:00:00 - 23:59:59:24
Media management information
・
Updated frame flags and valid frame flags
・
REC mark
Camera image mode
・60i：600
Example)
・60P：608
・30P：308
・24P：248
・24PN：24C
(During shooting)
・50i：502
・50P：50A
・25P：25A
・ ＊ ＊ P：＊＊ 9
(VFR 30PN or over 60P)
・ ＊ ＊ P：＊＊ 1
(VFR over 60P)
・ ＊ ＊ P：＊＊ D
(VFR 24PN during shooting)
・ ＊ ＊ P：＊＊ B
(VFR 25PN or over 50P)
– 96 –
Advertisement
Table of Contents
