Screen Status Display; Screen Display During Shooting - Panasonic HC-X1500 Operating Instructions Manual

Screen status display

Screen display during shooting

25
26
27
28
29
30
31
32
33
34
35
36
37
*1 Displayed when using
X2000
*2 The tally lamp is available when the handle unit (
1
Time code
Each time you press the USER button assigned to [COUNTER] or touch the USER button icon, the next display is shown or it switches to no display.
≥ [TCG **:**:**:**]: Displays the time code. [TCR **:**:**:**] will be displayed during playback.
≥ [UBG ** ** ** **]:Displays the user bits. [UBR ** ** ** **] will be displayed during playback.
≥ [CLIP *:**:**:**]: Displays the counter value of each clip. This is displayed when the [RECORDING] menu → [REC COUNTER] is set to
[CLIP]. Displays the counter value of the clip being played back during playback.
≥ [*:**:**:**]: Displays the cumulative counter value from the reset position. This is displayed when the [RECORDING] menu → [REC
COUNTER] → [TOTAL] is set.
2
Frame rate
≥ [S.SLOW120]: Displayed when set to the [SYSTEM] menu → [SUPER SLOW] → [ON] and the [SYSTEM] menu → [FREQUENCY] → [59.94Hz].
≥ [S.SLOW100]: Displayed when set to the [SYSTEM] menu → [SUPER SLOW] → [ON] and the [SYSTEM] menu → [FREQUENCY] → [50.00Hz].
≥ (No display): It is not displayed when set to the [SYSTEM] menu → [SUPER SLOW] → [OFF].
3
<AUTO/MANU> switch
Displayed when the <AUTO/MANU> switch is set to <AUTO>.
4
Message display area for stop of cooling fan
Displays a message when the cooling fan has stopped.
5
Recording status
Displays the recording status of the memory card in card slot 1 or card slot 2.
, : Not target for recording.
≥
(flashing), (flashing): Recognizing the memory card.
≥
≥ , : The recording is stopped while the recording target memory card is inserted.
, : Recording.
≥
(Flashing red dot),
≥
≥ [P ], [P ]: Recording is stopped with pre-recording is enabled and the recording target memory card is inserted.
≥ (No display): It is in one of the following conditions.
j A memory card has not been inserted.
j The memory card cannot be recognized.
The following indicators are displayed in card slot 1 only.
≥ [P]:Pre-recording is enabled, and the memory card is not inserted in the card slot, or the memory card is not recognized.
:The tally lamp is instructed to illuminate in red via network.
≥
:The tally lamp is instructed to illuminate in green via network while the recording is stopped.
≥
The tally lamp on the handle unit does not illuminate green.
Chapter 7 Output and Screen Display — Screen status display
1 2 3 4
TCG 1 2 : 3 4 : 5 6 : 2 8
S.SLOW120
2160-59.94p
MOV HEVC 200M
A001C001
IP REMOTE
ICONS
Ach 70%
CH1
30dB
CH2
15 16 17
VOLUME [ - ]
.
supplied,
X2000
(Flashing red dot): Processing to stop the recording.
5 6 7 5 6 8 9 10 11
999min 999min RELAY
HDMI INTRVL
ND1/16
DEC 3 1 2 0 2 0 1 0 : 4 5 : 3 0
ND:CLR 1/8000 STD
18 19 20 21
optional) is attached.
X1500
*2
*2
- 156 -
12 13 14
38
FBC DRS
39
FLUO
40
41
30
42
IR
43
D2x
44
MF99
+1.0EV
F5.6 iZ50
22 23 24
45
[ + ]