SAB Heli Division Goblin 700 Manual page 43

SPARE PARTS
Servo Mount SAB Fuel Sucker
[H0251-S] [H0705-S]
- 1 x Fuel Clunk.
- 1 x Tube
- 6 x Servo Mount. - 1 x Filter
Tensioner Idler
Reference Pin
[H1048-S] [H1066-S]
- 1 x Tail Belt Idler.
- 1 x Bushing.
- 2 x Flanged Bearing
- 1 x Reference Pin. - 1 x Washer.
Rear Servo Support Rear Servo Mount
[H1206-S] [H1207-S]
- 1 x Rear Servo Mount.
- 2 x Servo Spacer.
- 1 x Rear Servo Support. - 2 x Finishing Washer M2.5.
- 2 x Socket Screws M3x8mm. - 2 x Socket Screw M2.5x8mm.
Front Servo Mount Tail Blade Grips
[H1217-S] [H1233-S]
- 2 x Tail Blade Grip.
- 4 x Bearing
- 2 x Spacer
- 1 x Front Servo Mount. - 2 x Thrust Bearing
- 4 x Servo Spacer. - 2 x Socket Screw M3x6mm.
- 3 x Socket Screws M2.5x8mm. - 2 x Socket Screw M2x6mm.
Spindle FBL/RX Support
[H1263-S] [H1237-S]
- 1 x FBL Support.
- 2 x Spindle. - 1 x FBL Plate.
- 2 x Button Screws M6x10mm. - 1 x RX Plate.
- 2 x Washer. - 4 x RX Plate.
SAB Fuel Nipple
[H0708-S]
2.4x 4.5x106. - 1 x Fuel Nipple.
6 x 13.5x15mm. - 1 x Fuel Rubber 60 Shore.
Wire Cover
[H1107-S]
- 1 x Wire Cover.
- 1 x Finishing Washer M3.
3x 8x3 - 1 x Socket Screws M3x8mm.
- 2 x Button Screws M2.5x6mm.
Main Gear
[H1208-S]
- 1 x Main Gear.
- 1 x Bushing.
- 1 x Shoulder Screw M4x30.
- 1 x Spacer 10x
- 2 x Shim 10x
4x 9x2.5mm.
7x 9x0.5mm.
4x 9x4mm.
- 4 x Rubber.
- 4 x Flat Screw M3x5mm.
- 4 x Flat Screw M3x10mm.
- 3 x Socket Screw M3x6mm.
SAB Fuel Stop
[H0715-S]
- 2 x SAB Fuel Stop.
- 2 x T Connector.
Antena Cover
[H1134-S]
- 1 x Antena Cover.
- 1 x Double Side Tape.
16x1mm.
16x0.2mm.
Landing Gear Rod
[H1242-S]
- 2 x Landing Gear Rod.
- 4 x Plug.
Base Tail Belt Tensioner
[H1278-S]
- 1 x Bushing.
- 1 x Base Tail Belt Tensioner.
- 1 x Tensioner Column.
- 1 x Tensioner Spring.
- 1 x Shoulder Screw M3x22.
- 2 x Flanged Bearing 3x
Main Linkage
[H0722-S]
- 2 x Main Linkage.
- 4 x Plastic Uniball.
Swashplate
Blade Grips Arm
[H1202-S] [H1204-S]
- 2 x Blade Grips Arm. - 7 x Uniball M3.
- 2 x Uniball M3. - 1 x Reference Pin.
- 2 x Socket Screw M4x8. - 1 x Swashplate Assembly.
Serial Number Damper
[H1212-S] [H1216-S]
- 2 x Damper A.
- 1 x Serial Number. - 2 x Damper B.
- 1 x Flat Screw M2.5x5mm. - 2 x Damper C.
Tail Pitch Slider
[H1249-S]
- 1 x Tail Pitch Slider Assembled.
- 2 x Slider Linkage.
- 2 x Socket Screws M2x6mm.
- 2 x Spacer.
Center Hub Tail Case Group
[H1280-S] [H1306-S]
- 1 x Center Hub.
- 1 x Nylon Nut M4. - 1 x Tail Case Group.
- 1 x Socket Screw M4x20mm. - 4 x Button Screw M3x4mm.
- 2 x Socket Screw M3x12mm. - 2 x F_Bearing
7x3.
- 4 x Oring 70 .
- 4 x Oring 90 .
5x 13x4.
Page 42