Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for SAB Heli Division Goblin 770 helicopter
Summary of Contents for SAB Heli Division Goblin 770 helicopter
- Page 2 Goblin 770 Competition Manual Release 1.0 - December 2013 SAB HELI DIVISION S.R.L. Via San Crispino, 47 47030 San Mauro Pascoli (FC) - ITALY...
-
Page 3: Chapter 1, Serial Number
It is extremely important that you take a moment to register your helicopter with us. This is the only way to ensure that you are properly informed about changes to your kit, such as upgrades, retrofits and other important developments. SAB Heli Division cannot be held responsible for issues arising with your model and will not provide support unless you register your serial number. -
Page 4: Important Notes
*Lack of care with assembly or maintenance can result in an unreliable and dangerous model. *Neither SAB Heli Division nor its agents have any control over the assembly, maintenance and use of this product. Therefore, no responsibility can be traced back to the manufacturer. You hereby agree to release SAB Heli Division from any responsibility or liability arising from the use of this product. -
Page 5: Additional Components Required
The information is printed in a green box in the upper right hand corner of the Box 7: Landing gear support page at the beginning of every chapter. Copyright © 2013 - SAB Heli Division - All rights reserved Page 3... -
Page 6: Carbon Frame
We recommend de-burring the edges to minimize 4-Carbon Frame the risks of electrical wire cuts, etc. Very important in red line zone. Copyright © 2013 - SAB Heli Division - All rights reserved Page 4... - Page 7 ESC Support (H0153-S) Flat Head Cap Screw M2.5x5mm (HC128-S) Flat Head Cap Screw M2.5x5mm (HC128-S) Socket Head Cap Screw M2.5x8mm ..x2 Flat Head Cap Screw M2.5x5mm ..x10 Copyright © 2013 - SAB Heli Division - All rights reserved Page 5...
- Page 8 Main Frame 1 Finishing Washer M3 (H0354-S) (H0007-S) Cable Pass (HA010-S) ESC Support Assembly ESC Support Assembly Socket Head Cap Screw M3x10mm ..x2 Finishing Washer M3 ..x1 Copyright © 2013 - SAB Heli Division - All rights reserved Page 6...
- Page 9 Socket Head Cap Screw M3x10mm (HC056-S) Socket Head Cap Screw M3x10mm ..x5 Finishing Washer M3 Finishing Washer M3 (H0007-S) Socket Head Cap Screw M3x10mm (HC056-S) ..x4 Copyright © 2013 - SAB Heli Division - All rights reserved Page 7...
- Page 10 Yellow Landing Gear Nut M3 (H0345-S) Socket Head Cap Screw M3x12mm Metric Hex Nylon Nut M3 (HC206-S) ..x4 ..x8 Socket Head Cap Screw M3x10mm Finishing Washer M3 ..x4 ..x8 Page 8 Copyright © 2013 - SAB Heli Division - All rights reserved...
-
Page 11: Transmission Assembly
Chapter 5, Transmission Assembly 5 - Transmission Assembly Page 9 Copyright © 2013 - SAB Heli Division - All rights reserved... - Page 12 Socket Head Cap Screw Bearing 19x5mm M3x8mm Antenna Guide Bearing 24x6mm (H0050-S) ..(HC426-S) Button Head Cap Screw Button Head Cap Screw M3x4mm M3x4mm (HC038-S) .... Copyright © 2013 - SAB Heli Division - All rights reserved Page 10...
- Page 13 Socket Head Cap Screw Shouldered M2.5x19mm (HC033-S) .... Socket Head Cap Screw Socket Head Cap Screw Shouldered M4x24mm Socket Head Cap Screw M4x22mm M2x5mm ....Copyright © 2013 - SAB Heli Division - All rights reserved Page 11...
- Page 14 9x3mm ..Flanged Bearing 7x3mm Note: Position without preload. Insert the screw in the ..hole through the aluminum support as in the picture. Washer 4x0.5mm ..Copyright © 2013 - SAB Heli Division - All rights reserved Page 12...
- Page 15 For the cut, you can use an electric tool like a “Dremel” with a cut- off disc. Additionally, ensure the motor shaft has an appropriate 'flat' for one of the set screws. 0.2mm Copyright © 2013 - SAB Heli Division - All rights reserved Page 13...
-
Page 16: Main Rotor
Chapter 6, Head 6 - Main Rotor Page 14 Copyright © 2013 - SAB Heli Division - All rights reserved... - Page 17 Button Head Cap Screw (H0066-S) M6x10mm (HC122-S) H0346-S Left Thread Right Thread Plastic Ball Link (Initial length for the rods from the swash plate (H0066-S) to the Blade Grip.) Copyright © 2013 - SAB Heli Division - All rights reserved Page 15...
-
Page 18: Chapter 7, Assembling The Modules
Socket Head Cap Screw M3x8mm ..Finishing Washer M3 Socket Head Cap Screw M3x12mm .... Socket Head Cap Screw M4x24mm Metric Hex Nylon Nut M4 .... Copyright © 2013 - SAB Heli Division - All rights reserved Page 16... - Page 19 Socket Head Cap Screw M2.5x8mm Socket Head Cap Servo Spacer Screw M2.5x8mm ..x3 (HC020-S) (H0075-S) Socket Head Cap Screw M2.5x12mm Socket Head Cap Screw M2.5x12mm ..x9 (HC026-S) Copyright © 2013 - SAB Heli Division - All rights reserved Page 17...
- Page 20 Set Screw M2.5x40mm (HC242-S) Plastic ball link Plastic ball link (H0066-S) (H0066-S) Approx. 64 mm Initial length for the rods from the servos to the swash plate. Copyright © 2013 - SAB Heli Division - All rights reserved Page 18...
- Page 21 Figure 8: Shows the installation of a 2S battery for the flight control system. Alternatively, a BEC could be placed in the same area. ESC Cables 2S Battery or BEC Copyright © 2013 - SAB Heli Division - All rights reserved Page 19...
- Page 22 Socket Head Cap Screw M3x6mm (HC044-S) Double-sided Tape Support Flybarless (H0043-S) Spacer Support Flybarless (H0043-S) Socket Head Cap Screw M3x6mm Flate Head Cap Screw M3x8mm (HC044-S) (HC134-S) Copyright © 2013 - SAB Heli Division - All rights reserved Page 20...
-
Page 23: Chapter 11, Installation Of The Motor
Kontrionik Pyro 800-48 19T/20T 2000/2100 ± 12,5 KOSMIK 160/200 Note: Although the Goblin can fly at high rpm, for safety reasons we suggest to not exceed 2000 rpm. Copyright © 2013 - SAB Heli Division - All rights reserved Page 21... -
Page 24: Motor Belt Tension
Figure 1 shows the motor correctly wired. It is advisable to cover the wire joints between the motor and the ESC with heat shrink tubing. Motor Assembly Big Motor Belt (HC309-S) Copyright © 2013 - SAB Heli Division - All rights reserved Page 22... - Page 25 Chapter 12, Tail 7-Boom and Tail Page 23 Copyright © 2013 - SAB Heli Division - All rights reserved...
- Page 26 (H0261-S) Buttom Head Cap Screw M4x6mm Socket Head Cap Screw M2x6mm ...x2 (HC004-S) Socket Head Cap Screw M2x6mm Spacer Note: S >> Right Side ...x4 3x3mm (H0076-S) Page 24 Copyright © 2013 - SAB Heli Division - All rights reserved...
- Page 27 25T Pulley (H0155-S) ..Bell Crank Lever Socket Head Cap Screw Assembly M3x8mm ..Note: The set screw should align with the hole in the tail shaft Page 25 Copyright © 2013 - SAB Heli Division - All rights reserved...
-
Page 28: Tail Boom Assembly
DETAIL C Locking Element Tail (H0041-S) Metric Hex Nylon Nut M3 Locking Element (HC206-S) Tail Assembly H0041 Note: Metric Hex Nylon Nut M3 Double Sided Tape ..Copyright © 2013 - SAB Heli Division - All rights reserved Page 26... - Page 29 (HC062-S) ..Threaded Rod M2.5x40mm Threaded Rod M2.5x40mm (HC242-S) (HC242-S) Plastic Ball Link Carbon Rod 2.5x752mm Plastic Ball Link (H0066-S) (HC238-S) (H0066-S) Note: 12mm 12mm Approx 803mm Copyright © 2013 - SAB Heli Division - All rights reserved Page 27...
-
Page 30: Chapter 12, Tail Servo Installation
Please note that the boom edges might be rough and can eventually chafe or cut your tail servo lead - we recommend protecting the leads with heat shrink or even electrical tape. Copyright © 2013 - SAB Heli Division - All rights reserved Page 28... -
Page 31: Boom Assembly
Safety Lock Tail Boom ..x2 (H0038-S) Nylon Screw M8x20mm Socket Head Cap (HC165-S) Screw M3x12mm (HC062-S) Washer 3.1x 12x18mm (H0078-S) Socket Head Cap Screw M3x12mm (HC062-S) HA016 HC165 Copyright © 2013 - SAB Heli Division - All rights reserved Page 29... -
Page 32: Tail Belt Tension
It is recommended to attempt removal by forcing the canopy slightly to (figure 6). To lock the canopy saver, normal is ensure proper locking. possible to use a litle bit of CA Glue Copyright © 2013 - SAB Heli Division - All rights reserved Page 30... -
Page 33: Chapter 14, Battery
Using the velcro straps, making sure that the two locking pins are stopped against the frame spacer (Part1#H0003 and #H0151) Fig.6, 7. Flat Head Cap Screw M2.5x5mm (HC128-S) Battery Plate (H0149-S) Flat Head Cap Screw M2.5x5mm Cylinder M2.5 ..x2 (H0151-S) Copyright@2012 - SAB Heli Division - All rights reserved Page 31... -
Page 34: Chapter 15, In Flight
In this way, you will have extremely precise tail control even at low RPM. This pulley is available in the upgrade list [H0154-S] Copyright © 2013 - SAB Heli Division - All rights reserved Page 32... -
Page 35: Maintenance
*To ensure safety you should do a general inspection of the helicopter after each flight. You should check: The maintenance of proper belt tension. The proper isolation of wires from the carbon and aluminum parts. That all screws remain tight. Copyright@2013 - SAB Heli Division - All rights reserved Page 33... - Page 36 Flat Head Cap Screws M2.5 x 5mm H0157 Canopy Positioners Plastics HC134 Flat Head Cap Screws M2.5 x 8mm HC206 Metric Hex Nylon Nut M3 H0319 Canopy Poitioner Aluminum Page 34 Copyright © 2013 - SAB Heli Division - All rights reserved...
-
Page 37: Chapter 17, Exploded View, Transmission Assembly
16 x 0.2mm HC062 Socket Head Cap Screw M3 x 12mm HC414 Flanged Bearings 13 x 5mm H0142 Support Bearing Aluminum HC079 Socket Head Cap Screws M3 x 18mm Page 35 Copyright © 2013 - SAB Heli Division - All rights reserved... -
Page 38: Chapter 17, Exploded View, Head System
Socket Head Cap Screw Shouldered M4 x 24mm HC400 Flanged Bearings 2.5 x 6 x 2.5mm HC116 Socket Head Cap Screw Shouldereds M5 x 35mm H0158 Blade Washers 24 x 1mm Page 36 Copyright@2013 - SAB Heli Division - All rights reserved... -
Page 39: Chapter 17, Exploded View, Tail System
Tail rotor hub H0327 Tail blade grip H0358 Block Nut H0329 Tail Spindle HC134 Flat Head Cap Screws M3x8mm HC165 Nylon Screw M8x20mm H0330 Washer Spacer 9x0.75mm Page 37 Copyright © 2013 - SAB Heli Division - All rights reserved... -
Page 40: Chapter 18, Spare Parts
M3x22mm. - 4 x Socket Head Cap - 1 x Bell Crank Base. - 2 x Flanged Bearings 7x3mm. Screws M3x8mm. - 1 x Uniball M3x4 5H18. Copyright © 2013 - SAB Heli Division - All rights reserved Page 38... - Page 41 - 2 x Springs de 5.8/ df0.5 / LL9. -4 x Washers 16x0.2mm. M2.5x5mm - 2 x Springs de 3/ df0.5 / LL12. -4 x Orings 3050. - 1 x Heat Shrink. Copyright © 2013 - SAB Heli Division - All rights reserved Page 39...
- Page 42 - 2 x Washer 16x1mm. M4x10mm. - 1 x Set Screws M4x4mm. - 2 x Button Head Socket Cap M4x10mm. - 2 x Uniball M3x4 Ø5 H3.5. Copyright © 2013 - SAB Heli Division - All rights reserved Page 40...
- Page 43 - 2 x Canopy Grommet. - 1 x Canopy mousse. - 1 x Canopy mousse. - 1 x Canopy Edge Protection. - 1 x Canopy Edge Protection. Copyright © 2013 - SAB Heli Division - All rights reserved Page 41...
- Page 44 - 10 x Washer - 5 x Washer - 10 x Washer - 5 x Washer - 5 x Washer Screws M4x6mm. Ø2,2xØ5x0,3mm. Ø3xØ4x0,5mm. Ø3.3xØ6x0,5mm. Ø5.3xØ15x1mm. Ø6.3xØ15x1mm. Copyright © 2013 - SAB Heli Division - All rights reserved Page 42...
- Page 45 - 1 x One Way Bearings 14x12mm. - 1 x Foam Blade Holder - 2 x Hex Wrenches 2,5. - 1 x Canopy Mousse. - 2 x Cable Pass. Copyright © 2013 - SAB Heli Division - All rights reserved Page 43...
-
Page 46: Upgrades And Accessories
- 1 x SAB HELI DIVISION Decal ( set ). - 1 x SAB HELI DIVISION Keychain. - 1 x SAB HELI DIVISION Stand ( Set ). Copyright © 2013 - SAB Heli Division - All rights reserved Page 44... - Page 48 Manual Goblin 700 WWW.GOBLIN-HELICOPTER.COM REV. 01 Copyright@2011 – SAB Teli division – All rights reserved...