SAB Heli Division Goblin Kraken User Manual
  1. Manuals
  2. Brands
  3. SAB Heli Division Manuals
  4. Toy
  5. Goblin Kraken
  6. User manual

SAB Heli Division Goblin Kraken User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for SAB Heli Division Goblin Kraken

Summary of Contents for SAB Heli Division Goblin Kraken

  • Page 2 SAB Heli Division cannot be held responsible for any issues with your model and will not provide support unless you register your model.

  • Page 3: Introduction

    INTRODUCTION GOBLIN KRAKEN TECHNICAL SPECIFICATIONS Typical Motor : 12S, 500-560 Kv, 4525 - 4530 series, (max 62 mm diameter, max 70 mm height). Typical Speed Controller: 12S, 160/200 A Minimum tail blades size: 105mm Battery compartment: 12S, 4200/5500 mAh. Maximum tail blades size: 115mm (max 56mmx70mmx320mm).

  • Page 4: Important Notes

    PRODUCT, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. Further, in no event shall the liability of SAB Heli Division exceed the individual price of the Product on which liability is asserted. As SAB Heli Division has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury.

  • Page 5: Note For Assembly

    NOTE FOR ASSEMBLY ADDITIONAL COMPONENTS REQUIRED TOOLS, LUBRICANTS, ADHESIVES INSIDE THE MAIN BOX THERE ARE: Extra Card *Generic pliers. *Electronic Motor *Hexagonal driver, size 1.5, 2, 2.5, 3mm. *4/5mm T-Wrench. *Speed controller Product Card *5.5mm Socket wrench (for M3 nuts). Manual *Batteries: 12S –...

  • Page 6: Carbon Rod Assembly

    CARBON ROD ASSEMBLY BAG1 Carbon Rod 2.5x 4x702mm (HC537-S) Threaded Rod M2.5x40mm Threaded Rod M2.5x40mm (HC242-S) (HC242-S) NOTE: 13mm 13mm Aluminum Bushing Aluminum Bushing Approx 728mm Page 5...

  • Page 7: Transmission Group Assembly

    TRANSMISSION GROUP ASSEMBLY Foam 1, BAG2 Main Pulley Z60 (H1062-S) Metric Hex Rear Servo Mount Nylon Nut M3 (H1059-S) (HC206-S) Socket Head Cap Front Servo Mount Screw M3x10mm (H1088-S) (HC056-S) Front Tail Pulley Z27 (H1063-S) Socket Head Cap Screw M4x20mm (HC544-S) Finishing Washer M3 (H0007-S)

  • Page 8: Swashplate Servos Assembly

    SWASHPLATE SERVOS ASSEMBLY BAG3 SERVO ASSEMBLY The linkage ball must be positioned 18 mm out on the servo arm. The recommended servo arm to use is: SAB p/n [HA050/HA051]. Socket head cap screw M2.5x8mm Ensure the alignment of the servo arms (and sub trim set) before installation of the servos in the (HC020-S) model.

  • Page 9: Frame Group Assembly

    FRAME GROUP ASSEMBLY BAG4 BATTERY GUIDE ASSEMBLY RIGHT FRAME ASSEMBLY Main Frame (H1082-S) Flat Head Cap Low Side Frame Mount Screw M2.5x8mm (H1069-S) (HC125-S) Flat Head Cap Bushing on this side Screw M2.5x8mm (HC125-S) CF Xcross (H1085-S) Socket Head Cap Flat Head Cap Screw M3x8mm Screw M2.5x5mm...
  • Page 10 FRAME GROUP ASSEMBLY BAG4 Right Main Frame Assembled Socket Head Cap Screw M3x10mm (HC056-S) Left Main Frame Assembled Frame Spacer (H1076-S) Socket Head Cap Screw M3x6mm (HC044-S) Socket Head Cap Screw M3x10mm (HC056-S) Battery Guide Assembled Socket Head Cap Screw M3x6mm (HC044-S) Page 9...
  • Page 11 FRAME GROUP ASSEMBLY BAG5 Socket Head Cap TRANSMISSION GROUP Socket Head Screw M3x6mm ASSEMBLED Screw M3x10mm Canopy Base (HC044-S) (HC056-S) (H1101-S) CF Canopy CF Canopy Finishing Washer M3 Base Support Base Support (H0007-S) (H1113-S) (H1113-S) Socket Head Cap Canopy Base Screw M3x6mm (H1101-S) (HC044-S)

  • Page 12: Head Assembly

    HEAD ASSEMBLY Foam 2, BAG6 UNIBALL RADIUS ARM ASSEMBLY ...X2 CENTER HUB ASSEMBLY Spindle Flanged Bearing (H0079-S) Spacer Arm 2.5x 6x2.5mm 2.5x 4x6.3mm (HC400-S) eg: Microlube GL261 Uniball Radius Arm Center Hub (H0205-S) (H1043-S) Flanged Bearing 2.5x 6x2.5mm (HC400-S) Oring 90 Damper B Delrin (HC529-S) (H1046-S)
  • Page 13 HEAD ASSEMBLY Foam 2, BAG7 Washer NOTE: 16x1mm (HC230-S) Socket Head Cap Bearing The HPS head should be assembled with one, 1mm shim (HC230) on each side. The Screw M6x10mm 19x5mm blade grips must move freely, but they should not move just under their own weight. (HC124-S) (HC422-S) After approximately 10/20 flights, please check preload, you can add one or two 0.2mm...

  • Page 14: Assembling Of The Modules

    ASSEMBLING OF THE MODULES Foam 2, BAG8 Socket Head Cap HEAD GROUP SWASHPLATE ASSEMBLY Screw M3x12mm ASSEMBLED Uniball M3 (HC062-S) (H0065-S) Uniball M3 (H0065-S) Metric Hex Nylon Nut M4 (HC212-S) Socket Head Cap Screw Shoulder M4x24mm Socket Head Cap Swashplate SET (HC111-S) Screw M3x12mm (H1047-S)
  • Page 15 ASSEMBLING OF THE MODULES BAG8 LINKAGE ROD B ASSEMBLY ... X3 Approx 46mm Plastic ball link Plastic ball link (H0066-S) (H0066-S) Set Screw M2.5x18mm (HC140-S) Initial length for the rods from the servos to the swash plate. LINKAGE ROD B ASSEMBLY Page 14...

  • Page 16: Tail Group Assembly

    TAIL GROUP ASSEMBLY Foam 2, BAG9 Tail Shaft Assembled (H1089-S) Oring Spindle Shaft (HC335-S) (H0329-S) Spacer 8.5x0.75mm (H0330-S) Tail Blade Grip Assembled (H1033-S) Note: Larger ID eg: Microlube GL261 eg: Microlube GL261 Tail Pitch Slider Link Note: Smaller ID (H0261-S) Uniball M2.5x (H0064-S)
  • Page 17 TAIL GROUP ASSEMBLY Foam 2, BAG10 Tail Case Spacer Tail Side Plate (H1093-S) (H1097-S) Socket Head Cap Screw M2.5x8mm (HC020-S) Socket Head Cap Screw M3x8mm (HC050-S) TAIL ROTOR ASSEMBLED NOTE Lip Facing Down Tail Pulley (H1098-27-S) Uniball M3 Bell Crank Base (H0065-S) (H1095-S) Socket Head Cap...
  • Page 18 TAIL GROUP ASSEMBLY BAG11 Flat Head Cap Screw M3x10mm (HC135-S) CF Tail Plate (H1096-01-S) Metric Nylon Nut M3 Socket Head Cap (HC206-S) Screw M3x8mm (HC050-S) Tail Fin (H1096-02-S) Page 17...

  • Page 19: Tail Boom Assembly

    TAIL BOOM ASSEMBLY Foam 1, BAG12 Bolt M10 (HC546-S) Kraken Tail Boom (H1074-S) Boom Block Support (H1061-S) Nut M10 (HC546-S) Washer 16x0.2mm (HC232-S) Nut Block Lock the Nut Block (HC546-S) with a small qty of CA glue Use this special tool to apply the correct torque to the nuts.
  • Page 20 TAIL BOOM ASSEMBLY BAG13 Socket Head Cap Screws M3x12mm (HC062-S) Tail Belt 1926mm BOOM GROUP (HC324-S) Finishing ASSEMBLED Washer M3 (H0007-S) Double Sided Tape Finishing LOCKING ELEMENT Washer M3 TAIL ASSEMBLED (H0007-S) (H0041-S) TAIL GROUP Double ASSEMBLED Sided Tape Socket Head Cap Screws M3x12mm (HC062-S) Page 19...
  • Page 21 TAIL BOOM ASSEMBLY BAG14 Self Head Cap Screw M3x12mm TAIL SERVO ASSEMBLY Socket Head (HC549-S) Screw M3x6mm (HC044-S) Socket Head Servo Arm Servo Spacer TAIL BOOM Screw M2x6mm (HA050-S) (H0075-S) ASSEMBLED (HC004-S) Standard Uniball M2 SERVO ASSEMBLED Servo (H0064-S) Tail Servo Block (H0040-S) The distance between the axis and the ball must be around 18mm...
  • Page 22 TAIL BOOM ASSEMBLY BAG15 Before installing the plastic link on the threaded rod, be sure that you have waited at least 12 hours for the glue to fully cure. Plastic Ball Link Plastic Ball Link (H0066-S) (H0066-S) Approx 750mm NOTE: Before installing the plastic link onto the ball, be sure the tail push rod moves smoothly.
  • Page 23 TAIL BOOM ASSEMBLY BAG15 TAIL BOOM ASSEMBLY To fit the tail belt, loosen the tail case by loosening the 4 M3 screws (Figure 1). *Install the belt onto the tail front pulley, checking the direction of rotation. *Insert and tighten the four M4 screws of the boom plate. *Rotate the tail drive several times by hand.
  • Page 24 TAIL BOOM ASSEMBLY TAIL BELT TENSION To provide the correct tail belt tension, you can use the "zig-zag" method. Figure 1, Loosen the 2 RED screws and the BLUE and push the tail side in according with red arrow. Tighten the BLUE screw while you are pushing. Figure 2, Loosen the 2 RED screws and the YELLOW and push the tail side in according with red arrow.

  • Page 25: Low Side Frame Installation

    LOW SIDE FRAME INSTALLATION Foam 1, BAG16 Socket Head Cap Screw M3x8mm (HC050-S) Low Side Frame Mount (H1099-S) Page 24...

  • Page 26: Table Of Contents

    LOW SIDE FRAME INSTALLATION BAG16 Socket Head Cap Screw M3x10mm (HC056-S) Finishing Washer M3 (H0007-S) Low Side DX Frame (H1081-S) Socket Head Cap Screw M3x10mm (HC056-S) Finishing Washer M3 (H0007-S) Low Side SX Frame Finishing (H1080-S) Washer M3 (H0007-S) Socket Head Cap Finishing Socket Head Cap Screw M3x6mm...

  • Page 27: Landing Gear Installation

    LANDING GEAR INSTALLATION BAG17 Canopy Front Block (H1073-S) Plastic Landing Gear Support (H1070-S) Plastic Landing Gear Support (H1070-S) Landing Socket Head Cap Gear Plug Screws M2.5x10mm (HC022-S) Flat Head Cap Screws M3x8mm (HC134-S) If you use a 2s battery to power your RX, you can use H1131 as a battery mount.
  • Page 28 LANDING GEAR INSTALLATION BAG18 Socket Head Cap Screws M3x12mm Finishing Washer M3 (HC062-S) (H0007-S) Socket Head Cap Screws M3x12mm (HC062-S) Finishing Washer M3 LOW SIDE FRAME (H0007-S) ASSEMBLED LANDING GEAR ASSEMBLED Finishing Washer M3 (H0007-S) Finishing Washer M3 (H0007-S) Socket Head Cap Screws M3x12mm (HC062-S) Set Screw M4x4mm...

  • Page 29: Installation Of The Motor

    H0175-23-S - 23T Pinion = ratio 9.5:1 H0175-20-S - 20T Pinion = ratio 10.9:1 H0175-24-S - 24T Pinion = ratio 9.1:1 H0175-21-S - 21T Pinion = ratio 10.4:1 H0175-25-S - 25T Pinion = ratio 8.8:1 GOBLIN KRAKEN CONFIGURATIONS Rev:01 Pinion RPM Max Pitch...

  • Page 30: Socket Head Cap

    INSTALLATION OF THE MOTOR Foam 1, BAG19 Socket Head Cap Screw M3x8mm (HC050-S) Plastic ESC Support bearing support for the motor, H0143-S (H1068-S) Install the support after installing the pulley and Motor Pulley 21T after mounting the motor. (H0175-21-S) H0143 does not need to be used with an 8mm motor shaft.

  • Page 31: Finishing

    INSTALLATION OF THE MOTOR BAG20 Finishing You can use a 4-5mm shaft as a lever to set proper Washer M3 motor belt tension. (H0007-S) M3 Head Screw Socket Head Cap Screw M3x8mm (HC050-S) Motor Belt (HC535-S) Finishing Washer M3 (H0007-S) Socket Head Cap Screw M3x8mm MOTOR BELT TENSION...

  • Page 32: Installation Esc/Fbl/Rx

    INSTALLATION ESC/FBL/RX BAG21 Socket Head Cap Screw M2.5x10mm (HC022-S) Metric Hex Nylon Nut M2.5mm (HC200-S) NOTE: You can install some zip ties here. Metric Hex Nylon Metric Hex Nylon Nut M2.5mm Nut M2.5mm (HC200-S) (HC200-S) Page 31...
  • Page 33 INSTALLATION ESC/FBL/RX BAG22 IF YOU USE FBL WITH RX INTEGRATED IF YOU USE FBL AND SEPARATE RX (OPTION 1) Flat Head Cap Screws M2.5x5mm (HC128-S) Long FBL Support Flat Head Cap Screws M2.5x5mm (H1119-S) (HC128-S) Aluminum FBL Support Mount IF YOU USE FBL AND SEPARATE RX (OPTION 2) Socket Head Cap Screws M2.5x8mm (HC020-S)

  • Page 34: (Hc056-S)

    INSTALLATION ESC/FBL/RX BAGS 23, 28 In bag 28, you can find a “3D Printed” antenna support. Socket Head Cap Use it as desired with your RX system. Screw M3x12mm Antenna Support [H1134] (HC062-S) FBL SUPPORT ASSEMBLED Double Side-Tape (HA035-S) Button Head Cap Screw Special M2.5x6mm (HC019-S) Wire Support...
  • Page 35 INSTALLATION ESC/FBL/RX BAG23 Use hot glue to secure the wire connections. Servos Wire ESC Wire HA074-S Glued connector on the Carbon Support Zip-tie [HA058] Servos Wire Tail Servos Wire Follow the illustrated wiring solution. Use the servo extension for connecting the tail servo. Gluing of the connector on the carbon support is recommended as show in Figure 2.

  • Page 36: Installation Batteries

    INSTALLATION BATTERIES BAG24 IMPORTANT Before permanently mounting the batteries onto the battery tray, check the ideal position for the best center of gravity. Before flying, make sure that the locking pin is back in its resting position, blocking the battery tray in the correct position BATTERIES Use the included double side tape to...

  • Page 37: Installation Canopy

    INSTALLATION CANOPY BAG25 CANOPY *Install Canopy grommets (Figure.1) and the two quick knobs (Figure.2) *Fit the canopy in the red arrow zone, and insert the knobs. *Confirm the canopy is secure prior to each flight. Canopy Kraken (H1075-S) Canopy Grommet (HA021-S) Quick Knobs Page 36...

  • Page 38: In Flight

    IN FLIGHT BAG26 OPERATIONS BEFORE FLIGHT Socket Head Cap Shoulder M5x30mm *Set up the remote control and the flybarless system with utmost care. (HC114-S) *It is advisable to test the correct settings of the remote and flybarless system without main blades or tail blades fitted.

  • Page 39: Maintenance

    MAINTENANCE MAINTENANCE Take a look at the red parts. Check them frequently. All other parts are not particularly subject to wear. The lifespan of these components varies according to the type of flying. On average it is recommended to check these parts every 20 flights. In some instances, based on wear, these parts should be replaced every 100 flights. Periodically lubricate the tail slider movement and its linkages as well as the swash plate movement and its linkages.

  • Page 40: Transmission Module

    TRANMISSION MODULE TRANMISSION MODULE MAIN SHAFT REPLACEMENT The transmission module is supplied assembled and verified, ready to be used. K Gear Z72 0,75 For replacing the main shaft: (H1050-S) Explode and Spare Parts *Remove the serial number plate *Remove the M4x21 screw *Remove and replace the main shaft *Screw in the M4x21 screw, with high force and using green loctite Main Shaft...

  • Page 41: Check List

    CHECK LIST Check the dampening on the main and Tighten the main blades before flight. Check main hub screws(M4x24 and 2 M3x12) Check all power connectors tail rotor to be the same as always. Ensure they are tight. (Good mechanical connection). Check Tail &...

  • Page 42: Spare Parts

    SPARE PARTS Finishing Washer M3 Tail Servo Lock Locking Element Tail Linkage Tail Support Uniball M2 5H6 [H0007-S] [H0040-S] [H0041-S] [H0045-S] [H0064-S] - 5 x Uniballs M2 5H6. - 2 x Tail Servo Locks. - 2 x Locking Element Tails. - 5 x Uniball Spacers.

  • Page 43: - 2 X Finishing Washer M3

    SPARE PARTS Tail Blade Grips Center Hub Main Blade Grips Blade Grip Arm 30 Damper [H1033-S] [H1043-S] [H1044-S] [H1045-S] [H1046-S] - 2 x Aluminum Tail Blade Grip. - 4 x Bearing Ø5xØ10x4mm. - 2 x Thrust bearing Ø5xØ10x4mm. - 1 x Blade Grip. - 2 x Button Head Cap M4x8mm.
  • Page 44 SPARE PARTS Landing Gear Rod Canopy Front Block Tail Boom Kraken [H1071-S] [H1073-S] [H1074-S] - 1 x Canopy Front Block. - 1 x Tail Boom Kraken. - 2 x Landing Gear Rod. - 4 x Nylon Nut M2.5. - 2 x Locking Element Tail. - 2 x Double Sided Tapes.
  • Page 45 SPARE PARTS Low Side Frame Connection Tail Fin Tail Side Plate Tail Pulley 27T [H1096-02-S] [H1097-S] [H1098-S] [H1099-S] - 1 x Tail Fin. - 1 x Orange Stickers. - 2 x Flat Head Cap M3x10mm. - 1 x Yellow Stickers. - 1 x Tail Side Plate.
  • Page 46 SPARE PARTS [HC044-S] [HC050-S] [HC056-S] [HC062-S] [HC068-S] [HC074-S] [HC079-S] - 2 x Socket Head Cap - 2 x Socket Head Cap - 8 x Socket Head Cap - 8 x Socket Head Cap - 8 x Socket Head Cap - 8 x Socket Head Cap - 8 x Socket Head Cap Shoulder Screws M3x16.
  • Page 47 SPARE PARTS [HC324-S] [HC335-S] [HC400-S] [HC402-S] [HC410-S] [HC411-S] [HC414-S] - 4 x Flanged Bearing - 4 x Flanged Bearing - 4 x Flanged Bearing - 4 x Ball Bearing - 2 x Flanged Bearing - 1 x Tail Belt 1926mm. - 1 x Tail Oring.

Table of Contents