Assa Abloy SW200 Installation And Service Manual page 4

10 Pre-installation ........................................................................................................................................................................
10.1 General tips/Safety concerns .....................................................................................................................................................
10.2 Operator/Door handing ...............................................................................................................................................................
10.3 Installation examples ....................................................................................................................................................................
10.4 Fastening requirements (but not included) .........................................................................................................................
10.5 Tools required .................................................................................................................................................................................
11 Mechanical installation ........................................................................................................................................................
11.1 Surface mounted installation ....................................................................................................................................................
11.1.1 PUSH arm system .........................................................................................................................................................
11.1.1.1 Operator with PUSH arm system 95 mm .........................................................................................
11.1.1.2 Operator with PUSH arm system 210 mm ......................................................................................
11.1.2 PULL/PAS arm system ..................................................................................................................................................
11.1.2.1 Operator with PULL/PAS arm system 95 mm .................................................................................
11.1.2.2 Operator with PULL arm system 210 mm ........................................................................................
11.1.2.3 Cont. Operator with PULL arm system 210 mm ............................................................................
11.1.2.4 Cont. Operator with PULL arm system ..............................................................................................
11.1.2.5 Cont. Operator with PAS arm system ................................................................................................
11.1.3 Operator with sliding PUSH arm system ..............................................................................................................
12 Electrical connection .............................................................................................................................................................
12.1 Control units ....................................................................................................................................................................................
12.1.1 CU-200 .............................................................................................................................................................................
12.1.2 Arm system selection ..................................................................................................................................................
12.1.3 Extension units EXU-SI / EXU-SA .............................................................................................................................
12.1.4 Extension unit EXU-SI ..................................................................................................................................................
12.1.5 Extension unit EXU-SA ................................................................................................................................................
12.1.6 Installation on double doors ....................................................................................................................................
12.2 How to cut the jumper on the sync cable for double doors ...........................................................................................
12.3 Double door installations ...........................................................................................................................................................
12.4 Settings for double doors ............................................................................................................................................................
12.5 Sensor cable inlet ...........................................................................................................................................................................
12.6 Reset and indication device ......................................................................................................................................................
13 Start-up ......................................................................................................................................................................................
13.1 Adjusting the door stop ...............................................................................................................................................................
13.2 Auto-learn automatically sets back and latch check (recommended) .....................................................................
13.2.1 Push the LEARN BUTTON (LRN) ...............................................................................................................................
13.2.2 Double doors .................................................................................................................................................................
13.3 General adjustment ......................................................................................................................................................................
13.4 Connection of activation units and accessories ..................................................................................................................
14 Cover ..........................................................................................................................................................................................
14.1 Fitting and removing the cover .................................................................................................................................................
14.2 Cover piece kit ................................................................................................................................................................................
15 Signage .......................................................................................................................................................................................
16 Advanced settings ..................................................................................................................................................................
16.1 Learn with advanced setting of "back- and latch-check" ..................................................................................................
16.2 Revert to default values for "back- and latch-check" (Level 1) .......................................................................................
16.3 Changing group of parameters (Level 2) ...............................................................................................................................
16.4 Classification (Level 3) .................................................................................................................................................................
16.5 O verhead Presence Detection (OPD) Monitoring (Level 4) ...........................................................................................
16.6 Lock kick (Level 5) ..........................................................................................................................................................................
17 Reducing / Increasing the "Spring pre-tension" (SPTE) .............................................................................................
18 Guide for installation and adjustments ..........................................................................................................................
18.1 Complementary Safety Devices Swing Doors ......................................................................................................................
18.2 Swing Doors Opening and Closing Time ................................................................................................................................
18.2.1 How to find the correct opening and closing time ...........................................................................................
18.3 Diagrams for Door weight ..........................................................................................................................................................
18.3.1 Aluminium frame with glass .....................................................................................................................................
4 Issue 2021-02-24
30
30
30
31
31
32
33
33
34
35
38
41
42
44
45
46
47
49
50
51
51
52
53
54
55
56
56
56
57
58
59
61
61
63
64
64
64
66
67
67
68
69
70
70
70
71
73
74
75
76
77
77
77
77
78
78
1009728-en-9.0