Additional Items Required; Required Hardware And Accessories For Gas Engine Installation; Adhesives And Building Supplies; Optional Supplies And Tools - GREAT PLANES GIANT BIG STIK XL 55-61cc/EP ARF Instruction Manual

❍ (1) 1300mAh LiFe Ignition Battery (HCAM6411)
❍ (1) 3200mAh LiFe Receiver Battery (HCAM6446)
The following are additional items required if using the
recommended Futaba S9452 servos from the Basic Set-up
(non S.Bus servos).
❍ (6) Futaba S9452 Digital Servos (FUTM0662)
❍ (1) S.Bus Hub w/Cable 12" (300mm) (FUTM4195)
❍ (3) S.Bus Decoder (400mm) (FUTM4193)
❍ (1) S.Bus Channel Changer (FUTM4190) Required if
your transmitter does not have an S.Bus Connector
(check your transmitter instruction manual).

ADDITIONAL ITEMS REQUIRED

Required Hardware and Accessories
for Gas Engine Installation
(2) Dubro #813 1/8" Fuel Line Barb (DUBQ0670)
(1) Dubro #800 Large Tygon Fuel Line (DUBQ0493)
(1) Propeller Drill Guide (DLEQ0551)
Propeller and spare propellers suitable for your engine.

Adhesives and Building Supplies

This is the list of Adhesives and Building Supplies that are
required to fi nish the 55cc Big Stik ARF.
❍ 1 oz. [28 g] Thin CA (GPMR6002)
❍ 2 oz. [57g] Spray CA Activator (GPMR6035)
❍ Pro 30-Minute epoxy (GPMR6043)
❍ Pro 6-Minute Epoxy (GPMR6042)
❍ Threadlocker thread-locking compound (GPMR6060)
❍ Mixing Sticks (GPMR8055)
❍ Mixing Cups (GPMR8056)
❍ Epoxy Brushes (GPMR8060)
❍ Denatured Alcohol (for epoxy clean up)
❍ #64 Rubber Bands
❍ Masking Tape
❍ Paper Towels
❍ Drill
❍ Drill Bits: 1/16" [1.5mm], 3/32" [2.5mm], 7/64" [2.8mm],
1/8" [3mm], 3/16" [4.5mm], 13/64" [5mm], 5/16" [8mm]
❍ Small Metal File
❍ Stick-On Segmented Lead Weights (GPMQ4485)
❍ Silver Solder w/Flux (STAR2000)
❍ Hobbico 60-Watt Soldering Iron (HCAR0776)
❍ #1 Hobby knife (RMXR6903)
❍ #11 Blades (5-pack, RMXR6930)
❍ Rotary Tool such as Dremel
❍ Rotary Tool Reinforced Cut-Off Wheel (GPMR8200)
❍ R/C Foam Rubber (1/4" [6mm] (HCAQ1000) or ½"
[13mm] (HCAQ1050)
Covering Tools
❍ Top Flite MonoKote Sealing Iron (TOPR2100)
❍ Top Flite Hot Sock Iron Cover (TOPR2175)
❍ Top Flite MonoKote Trim Seal Iron (TOPR2200)
❍ Top Flite MonoKote Heat Gun (TOPR2000)
❍ Coverite 21
st
Century Sealing Iron (COVR2700)
❍ Coverite 21
st
Century Cover Sock (COVR2702)
❍ Coverite 21
st Century Trim Sealing Iron (COVR2750)

Optional Supplies and Tools

Here is a list of optional tools mentioned in the manual that
will help you build the 55cc Big Stik ARF
❍ CA applicator tips (HCAR3780)
❍ CA debonder (GPMR6039)
❍ 36" metal ruler
❍ Pliers with wire cutter
❍ Robart Super Stand II (ROBP1402)
❍ Servo horn drill (HCAR0698)
❍ AccuThrow Defl ection Gauge (GPMR2405)
❍ CG Machine™ (GPMR2400)

IMPORTANT BUILDING NOTES

You will see this symbol anytime a threaded screw
or nut is installed. We recommend that a drop
of threadlocker be applied to the threads. An
exception, do not use threadlocker on the screws
installed in the nylon control horns.
You will see this symbol anytime
epoxy is recommend. A paper
towel dampened with denatured
alcohol is great for cleaning epoxy
from surfaces before the epoxy
cures.
Anytime a hole needs to be drilled you will see
this symbol with the recommended size drill bit.
Replacement MonoKote Colors
Jet White (TOPQ0204)
Black (TOPQ0208)
True Red (TOPQ0227)
6
6 Minute Epoxy 30 Minute Epoxy