Table of Contents
Advertisement
the instructions may differ slightly from the photos. In those
instances the written instructions should be considered
as correct.
3. You must take time to build straight, true and strong.
4. You must use an R/C radio system that is in first-class
condition, and correctly sized components (batteries,
hardware, etc.) throughout the building process.
5. You must correctly install all R/C and other components so
that the model operates correctly on the ground and in the air.
6. You must check the operation of the model before every
flight to insure that all equipment is operating and that the
model has remained structurally sound. Be sure to check
clevises or other connectors often and replace them if they
show any signs of wear or fatigue.
7. If you are not an experienced pilot or have not flown this
type of model before, we recommend that you get the
assistance of an experienced pilot in your R/C club for your
first flights. If you're not a member of a club, your local hobby
shop has information about clubs in your area whose
membership includes experienced pilots.
8. WARNING: The fuselage included in this kit is made of
fiberglass, the fibers of which may cause eye, skin and
respiratory tract irritation. Never blow to remove fiberglass
dust, as the dust will blow back into your eyes. Always wear
safety goggles, a particle mask and rubber gloves when
grinding, drilling and sanding fiberglass parts. Vacuum the
parts and the work area thoroughly after working with
fiberglass parts.
We, as the kit manufacturer, provide you with a top quality,
thoroughly tested kit and instructions, but ultimately the
quality and flyability of your finished model depends on
how you build it; therefore, we cannot in any way
guarantee the performance of your completed model, and
no representations are expressed or implied as to the
performance or safety of your completed model.
Remember: Take your time and follow the instructions to
end up with a well-built model that is straight and true.
DECISIONS YOU MUST MAKE
This is a partial list of items required to finish the Fling 2M ARF
that may require planning or decision making before starting to
build. Order numbers are provided in parentheses.
Radio Equipment
If purchasing a complete system, the Futaba
stick, 3-channel transmitter with R114ZH mini receiver and
two S3003 standard servos is recommended (FUTJ52**).
Replace the "**" with the channel number you wish to order.
(For example, if you wish to order a system on channel 44,
order FUTJ5244).
The 3FR does not come with the battery needed for the
Fling 2M ARF. The Great Planes 4.8V 350mAh NiMH battery
is best suited for this plane and is recommended.
If you are purchasing your components separately, refer to
the following list for guidelines or ordering numbers.
•
Any 2-channel (or more) 72 MHz FM transmitter, such
as the Futaba 3FR (FUTJ52**)
•
Great Planes ElectriFly
crystal (GPML0044 for low band, GPML0045 for high
band) or similar lightweight micro receiver.
•
Low band receiver crystal for Great Planes mini
receivers (channels 11 to 35, FUTL62**)
•
High band receiver crystal for Great Planes mini
receivers (channels 36 to 60, FUTL63**)
•
(2) Micro servos, such as the Futaba S3101 micro
precision servos (FUTM0033)
•
(2) Standard servos, such as the Futaba S3003
servo (FUTM0031)
•
Great
battery (GPMP0950)
•
Hobbico
J-connectors (HCAM2000) (for battery to receiver connection)
Note: An on/off receiver switch is not used. When ready to
fly, the battery is simply connected to the receiver.
ADDITIONAL ITEMS REQUIRED
Adhesives and Building Supplies
This is the list of hardware and accessories required to finish the
Fling 2M ARF. Order numbers are provided in parentheses.
❏
Up-Start 2m (up to 200' launches at sites with 300' or
more launch area) (DYFP8305)
❏
Great Planes Pro
Great Planes Pro 6-minute epoxy (GPMR6042)
❏
Hobbico #1 Hobby knife (HCAR0105)
❏
Hobbico #11 Blades (5-pack, HCAR0211)
❏
Hobbico 1/4" [6 mm] R/C foam rubber – (HCAQ1000)
❏
3/32" [2.4 mm] Drill bit
❏
Great Planes stick-on segmented lead weights (GPMQ4485)
®
3FR single
3
™
4-channel mini receiver w/o
-or-
Planes
4.8V
350mAh
®
6" [153 mm] Command Extension with Futaba
™
30-minute epoxy (GPMR6047) or
NiMH
receiver
Advertisement
Table of Contents
