Additional Items Required; Adhesive And Building Supplies; Covering Tools; Optional Supplies And Tools - GREAT PLANES ULTRA SPORT 46 Instruction Manual

ADDITIONAL ITEMS REQUIRED FOR
ELECTRIC MOTOR INSTALLATION
(1) 8" Servo extension (FUTM4140) (for ESC)
OR
(1) 6" Servo extension (TACM2701) (for ESC)
ADDITIONAL ITEMS REQUIRED FOR
GLOW ENGINE INSTALLATION
(1) Heavy duty on/off switch (FUTM4385) (TACM2761)
(1) Ernst Charge Receptacle (ERNM3001)
(1) 1300mAh LiFe receiver battery (HCAM6411)

ADDITIONAL ITEMS REQUIRED

Adhesive and Building Supplies

This is the list of Adhesives and Building Supplies that are
required to fi nish the Ultra Sport .46/EP.
1/2 oz. [15g] Thin Pro CA (GPMR6001)
Pro 30-minute epoxy (GPMR6047)
Pro 6-minute epoxy (GPMR6045)
Threadlocker thread locking cement (GPMR6060)
Mixing sticks (50, GPMR8055)
Mixing cups (GPMR8056)
Epoxy brushes (6, GPMR8060)
Denatured alcohol (for epoxy clean up)
Masking tape
Drill
Drill bits: 1/16" [1.5mm], 5/64" [2mm], 3/32" [2.5mm],
11/64" (4.5mm), 3/16" [5mm]
Small metal fi le
Stick-on segmented lead weights (GPMQ4485)
#1 Hobby knife (RMXR6903)
#11 blades (5-pack, RMXR6930)
Rotary tool such as Dremel
Rotary tool reinforced cut-off wheel (GPMR8200)
Great Planes Dead Center hole locator (GPMR8130)
#64 Rubber Bands (HCAQ2020)

Covering Tools

Top Flite MonoKote Sealing Iron (TOPR2100)
Top Flite Hot Sock Iron Cover (TOPR2175)
Top Flite MonoKote Trim Seal Iron (TOPR2200)
Top Flite MonoKote Heat Gun (TOPR2000)
Coverite 21 st Century Sealing Iron (COVR2700)
st
Coverite 21 Century Cover Sock (COVR2702)
Coverite 21 st Century Trim Sealing Iron (COVR2750)

Optional Supplies and Tools

Here is a list of optional tools mentioned in the manual that
will help you build the Ultra Sport .46/EP.
2 oz. [57g] spray CA activator (GPMR6035)
CA applicator tips (HCAR3780)
CA debonder (GPMR6039)
36" metal ruler
Pliers with wire cutter (HCAR0625)
Robart Super Stand II (ROBP1402)
Servo horn drill (HCAR0698)
AccuThrow Defl ection Gauge (GPMR2405)
CG Machine™ (GPMR2400)
Precision Magnetic Prop Balancer™ (TOPQ5700)

IMPORTANT BUILDING NOTES

Anytime thin CA glue is recommended
you will see this symbol. When threading
screws into wood, we recommend that
fi rst the screw be installed. Then, remove
the screw and apply a couple of drops
of thin CA in the hole to harden the
threads. After the CA has hardened,
reinstall the screw.
Anytime threadlocker is recommended
you will see this symbol. We recommend
that anytime a threaded screw or nut is
installed, a drop of medium threadlocker
be applied to the threads. An exception:
Do not use threadlocker on screws
installed in the nylon control horns.
Anytime epoxy is recommended you will
see this symbol. 6-minute epoxy can be
used most of the time, but if a step will
require time to assemble, 30-minute
epoxy is recommended.
Anytime a hole needs to be drilled
you will see this symbol with the
recommended size drill bit.
Denatured alcohol is great for
cleaning epoxy from surfaces before
the epoxy cures.
When connecting servo extensions
to servos, we recommend that the
connection be secured with heat
shrink or tape (not included).
4