YASKAWA VARISPEED-616G5 Instruction Manual page 354

integral reset, V/f control with PG
integral time
flux vector control, 6 - 36, 6 - 44
low-speed gain, 6 - 36, 6 - 44
proportional gain
flux vector control, 6 - 36, 6 - 44
low-speed gain, 6 - 36, 6 - 44
responsiveness, flux vector control
,
V/f control with PG 6 - 44
speed control gain, flux vector control
,
fine adjustments 6 - 38
,
speed control integral reset 7 - 67
speed control proportional gain
,
speed feedback 7 - 5
,
speed limit function 7 - 22
,
speed search function 7 - 44
,
speed torque control change
stall prevention function settings
,
Status Monitor 4 - 12
,
stopping method 6 - 12
,
coasting 6 - 12
,
coasting with timer 6 - 13
,
DC injection braking 6 - 12
,
deceleration 6 - 12
,
flux vector control 6 - 31
,
surge absorber 3 - 14
,
SVE (zero servo fault) 9 - 4
switching, speed control and torque control
,
timer 7 - 28
T
,
temperature 2 - 6
,
terminal block 3 - 5
,
timer function 7 - 45
torque compensation function
,
torque control 1 - 4, 7 - 21
,
torque limits 7 - 4, 7 - 30
,
analog inputs 7 - 4, 7 - 30
,
torque reference 7 - 21
,
primary filter 7 - 25
Transmission Option Card DPRAM error (CPF23)
Transmission Option Card model code error (CPF22)
Transmission Option Card self diagnostic error (CPF21)
trim control increase and decrease
,
6 - 45
,
6 - 37
,
6 - 38
,
7 - 75
7 - 74
,
7 - 87
,
7 - 27
,
7 - 25, 7 - 55
,
9 - 5
,
9 - 5
,
9 - 5
,
7 - 70
Index
,
troubleshooting 9 - 1, 9 - 9
U
up and down commands
,
user constants 4 - 23
application constants
autotuning
acceleration/deceleration, 8 - 11
carrier frequency, 8 - 15
factory tuning, 8 - 16
hunting prevention, 8 - 15
motor slip compensation, 8 - 12
S-curve acceleration/deceleration, 8 - 12
speed control, 8 - 14
torque compensation, 8 - 13
autotuning constants
constants with factory settings dependent on
control method
constants with factory settings dependent on
inverter capacity
,
DC braking 8 - 6
,
droop control 8 - 9
,
dwell functions
,
factory settings 12 - 15
,
initializing 4 - 21
lists
initialize mode, 8 - 3
programming mode, 8 - 5
,
motor constants
motor 2 control method, 8 - 22
motor 2 setup, 8 - 23
motor 2 V/f pattern, 8 - 22
motor setup, 8 - 21
V/f pattern, 8 - 20
operation mode selections
operator constants
monitor selections, 8 - 43
multi-function selections, 8 - 44
,
options 8 - 24
other option setup, 8 - 26
PG option setup, 8 - 24
,
PID control 8 - 8
protection constants
fault restart, 8 - 39
hardware protection, 8 - 41
motor overload, 8 - 35
power loss ridethrough, 8 - 35
reference directions, 8 - 39
stall prevention, 8 - 37
torque detection, 8 - 40
torque limits, 8 - 40
reference constants
Index- 5
,
7 - 68
,
8 - 5
,
8 - 11
,
8 - 45
,
8 - 47
8 - 9
8 - 20
,
8 - 5
,
8 - 43
,
8 - 35
,
8 - 17