Switching The Me Area In The Control Panel Av-Hs60C1/Av-Hs60C2/Av-Hs60C4 - Panasonic AV-HS6000 Series Operation Manual

If [AUX1] to [AUX4] are set to [On] in the [AUX Trans] column, select the source signal that is changed by the corresponding KEY bus crosspoint
buttons.
At this time, the MIX transition is performed at the transition time specified in [AUX1] to [AUX4] in the [Trans Time] column.
During transition, KEY crosspoint buttons denoting the transition source lights in the Preset tally color, and the KEY bus crosspoint buttons denoting the
transition target source lights in the Low tally color.
When the transition is completed, the transition source button goes off, and the transition target button lights in the Low color.
When another signal is selected during transition, the transition processing continues from that midway point.
Switching the ME area in the Control Panel AV‑HS60C1/AV‑HS60C2/AV‑HS60C4
Switch the ME1 and ME2 in the Control Panel AV-HS60C1/AV-HS60C2/AV-HS60C4.
f The following figure shows the area that can be switched.
r AV‑HS60C1/AV‑HS60C2
1 2 3 4
Black SDI SDI SDI
IN1 IN2 IN3
1 2 3 4
Black SDI SDI SDI
IN1 IN2 IN3
r AV‑HS60C4
NOTE
@
t <AUX1/2> to <AUX15/16> buttons, <VMEM F/S> button, <DISP> button, <DSK1 F/S> to <DSK4 F/S> buttons, DSK operation area, positioner area,
and Menu Panel AV-HS60C3 are not subject for switching.
t If you perform switching using the KEY bus selector buttons on the upper ME line (1st Line) while <AUX 1/2> to <AUX 15/16> buttons are selected,
the selection status of the KEY bus crosspoint buttons on the lower ME line (2nd Line) takes over the KEY bus crosspoint buttons on the upper ME
line (1st Line) before switching, and the KEY bus selector button lamps all turn off. Press the KEY bus selector buttons on the lower ME line (2nd Line)
to turn on the lamps and change the operation targets of the KEY bus crosspoint buttons to the appropriate bus.
Switching the ME area in the Menu Panel AV‑HS60C3
1
Select the <CONF> button → [OPERATE] → [MECHG] tab.
2
Select an item in [1st Line] and [2nd Line] in the [MainPanel]/[SubPanel1]/[SubPanel2] column.
[ME1]
[ME2]
f If the item set for [ME1] is switched to [ME2], the item selected for [ME2] is switched to [ME1].
Chapter 7 CONFIG Menu — Setting the operation mode
5 6 7 8 9 10 11 12 13 14 15 16 17
SDI SDI SDI SDI SDI SDI SDI SDI SDI Still Still Still Still
IN4 IN5 IN6 IN7 IN8 IN9 IN10 IN11 IN12 1V 2V 3V 4V
5 6 7 8 9 10 11 12 13 14 15 16 17
SDI SDI SDI SDI SDI SDI SDI SDI SDI Still Still Still Still
IN4 IN5 IN6 IN7 IN8 IN9 IN10 IN11 IN12 1V 2V 3V 4V
1 2 3 4 5 6 7 8
Black SDI SDI SDI SDI SDI SDI SDI
IN1 IN2 IN3 IN4 IN5 IN6 IN7
1 2 3 4 5 6 7 8
Black SDI SDI SDI SDI SDI SDI SDI
IN1 IN2 IN3 IN4 IN5 IN6 IN7
The corresponding ME area is used as ME1.
The corresponding ME area is used as ME2.
ME1 ME2 SEL
XPT DSK AUK CBGD
BUS
SHFT
SHOT000 SHOT001 SHOT002
1-1 1-2 1-3
18 19 20 21 22 23 24
Clip Clip Clip Clip CBGD ME1 ME2
SHOT003
1V 2V 3V 4V 1 PGM PGM
1-4 1-5 1-6
1-7 1-8 1-9
RECALL
PLAY
STORE
DEL
STILL1 OP
BUS
SHFT
4-1 4-2 4-3
18 19 20 21 22 23 24
Clip Clip Clip Clip CBGD ME1 ME2
1V 2V 3V 4V 1 PGM PGM
4-4 4-5 4-6
4-7 4-8 4-9
RECALL
STORE
DEL
ME1 ME2 SEL STILL1
XPT DSK AUK CBGD
SHOT000 SHOT001 SHOT002
1-1 1-2 1-3
4-1 4-2
SHOT003
1-4 1-5 1-6
4-4 4-5
1-7 1-8 1-9
4-7 4-8
RECALL RECALL
PLAY
STORE STORE
DEL DEL
BUS
SHFT
9 10 11 12 13 14 15 16
SDI SDI SDI SDI SDI Still Still Still
IN8 IN9 IN10 IN11 IN12 1V 2V 3V
BUS
SHFT
9 10 11 12 13 14 15 16
SDI SDI SDI SDI SDI Still Still Still
IN8 IN9 IN10 IN11 IN12 1V 2V 3V
– 137 –
CHR LIN LUM FULL
MIX MIX MIX WIPE
02s01f 01s00f 01s00f 01s00f
ME1
MIX
01s00f
CG5V CG6V
CHR LIN FULL FULL
WIPE MIX MIX MIX
01s00f 01s00f 01s00f 01s00f
ME2
MIX
01s00f
CG5V CG6V
OP
4-3
4-6
4-9 CG1V CG2V CG3V CG4V
LIN LUM FULL
CHR
MIX MIX MIX WIPE
02s01f 01s00f 01s00f 01s00f
ME1
MIX
01s00f
CG5V CG6V CAM1 CAM2
LIN FULL FULL
CHR
WIPE MIX MIX MIX
01s00f 01s00f 01s00f 01s00f
ME2
MIX
01s00f
CG5V CG6V CAM1 CAM2
CAM1 CAM2
CAM1 CAM2 CG1V CG2V CG3V CG4V