Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. Switch
  5. AV-HS6000
  6. Firmware upgrade manual

Panasonic AV-HS6000 Firmware Upgrade Manual

2me live switcher
Hide thumbs Also See for AV-HS6000:
1
2
3
4
5

Advertisement

Quick Links

Download this manual See also: Operating Manual
Follow the steps below to upgrade the AV-HS6000 software version.
1. Check the software version
2. Save project files
3. Upgrade the Main Frame
4. Upgrade the Control Panel
5. Verify the software version
6. Initialize the AV-HS6000
7. Load project files
This document describes menu operations via the Menu Panel, but you can perform the same operations via a standard DVI
monitor and mouse.
 Refer to "Chapter 4 Preparations – Basic menu operations" in the Operating Guide.
A memory card is required to upgrade the AV-HS6000 software version.
p p There must be at least 200 MB of free space on the memory card.
p p SDXC memory cards are not supported.
p p Use a memory card that has been initialized on the AV-HS6000 beforehand.
 Refer to "Chapter 5 Basic Operations – Storage Initializing a memory card " in the Operating Guide.
„ Notes on network settings
„
The following settings will be initialized when upgrading from Ver. 3 or earlier of the AV-HS6000 software.
p p <SYS> button  [SYSTEM]  [Network] tab  [Network1] column setting
p p <SYS> button  [SYSTEM]  [Network] tab  [Network2] column setting
p p <SYS> button  [CTRL PANEL]  [SubPanel1] tab  [Network] column setting
p p <SYS> button  [CTRL PANEL]  [SubPanel2] tab  [Network] column setting
The above settings are not saved to project files.
Make a memo of the settings before upgrading the software, and reconfigure the settings after upgrade is complete.
„ Notes on macro data compatibility
„
Macro data which stores menu operations performed after pressing the <SYS> button or <CONF> button may not play back
properly after upgrading the software.
Delete macro register memories that contain such recorded operations after upgrading the software, and perform and
register the operations again.
In addition, when upgrading from Ver. 2 of the software to Ver. 3, macro data compatibility issues other than menu operations
performed after pressing the <SYS> button or <CONF> button may occur.
For details, see "Appendix: Notes on Upgrading from Ver. 2 to Ver. 3" on page 5.
W0614TY3066 -FJ
2ME Live Switcher AV-HS6000
Firmware Upgrade Guide

Important Notes

1
VQT5L08-3

Advertisement

loading

Related Manuals for Panasonic AV-HS6000

Summary of Contents for Panasonic AV-HS6000

  • Page 1: Important Notes

    „ Notes on network settings „ The following settings will be initialized when upgrading from Ver. 3 or earlier of the AV-HS6000 software. p p <SYS> button  [SYSTEM]  [Network] tab  [Network1] column setting p p <SYS> button  [SYSTEM]  [Network] tab  [Network2] column setting p p <SYS>...

  • Page 2: Check The Software Version

    [Status] tab in the menu screen. p p Eject the memory card p p Turn off the AV-HS6000 Main Frame or Control p p The system version of the AV-HS6000 is displayed in the Panel [System Version] field under the [System Version] column.
  • Page 3 4. Upgrade the Control Panel Press the button that is blinking red. Version upgrade of the Control Panel starts, and the When you perform the following, the version upgrade data is Control Panel enters the following state. transferred from the Main Frame to the Control Panel, and the software version of the Control Panel is upgraded.

  • Page 4: Verify The Software Version

    [Status] tab in the menu screen. Panel to light it, and select the [PROJECT]  [SD/ The system version of the AV-HS6000 is displayed in the SSD] tab in the menu screen. [System Version] field under the [System Version] column.
  • Page 5 Appendix: Notes on Upgrading from Ver. 2 to Ver. 3 When a macro register memory saved in Ver.2 of the AV-HS6000 software (Ver2.xx-xx-x.xx) is played back in Ver.3 of the software (Ver3.xx-xx-x.xx), the stored operations may not play back properly.