Dsk Transition; Dsk Output; Adjusting The Luminance Key/Linear Key - Panasonic AV-HS6000 Series Operation Manual

DSK transition

Operating in the DSK operation area
r Operating the <DSK1 TRNS> to <DSK4 TRNS> buttons
Press the <DSK1 TRNS> to <DSK4 TRNS> buttons in the transition area to execute a transition automatically with the transition time of respective keys
set on the menu.
The <DSK1 TRNS> to <DSK4 TRNS> buttons flicker during key in, and light when the transition is complete. If the <DSK1 TRNS> to <DSK4 TRNS>
buttons are pressed while key in is complete, transition of the key image (key out) is executed.
The <DSK1 TRNS> to <DSK4 TRNS> buttons light during key out, and go off when the transition is complete. If the <DSK1 TRNS> to <DSK4 TRNS>
buttons are pressed during the transition, the transition direction is reversed.
r Operating the <DSK1 ON> to <DSK4 ON> buttons
Press the <DSK1 ON> to <DSK4 ON> buttons to turn on/off respective DSK with the cut transition.
Setting the DSK transition mode
Transition mode and transition time can be set separately for key in and key out.
1
Select the <DSK MISC> button → [DSK1] to [DSK4] → [Transition] tab.
2
Select an item in [Transition] in the [In Type]/[Out Type] column.
f The transition mode available is only [MIX].
[Off]
[On]
3
Set [Time] in the [In Type]/[Out Type] column.
f Set the transition time.
4
Select an item in [In=Out] in the [Out Type] column.
[Off]
[On]

DSK output

The DSK block outputs the following signals.
For details, refer to "System Menu" (page 140).
f DSKPGM1, DSKPGM2: Outputs program signals of DSK compositions.
Select the <SYS> button on the top menu → [MAIN FRAME] → [DSK] tab → [Config] column → [DSK1] to [DSK4] and set them to either [DSKPGM1]
or [DSKPGM2] to assign the signal to one of the outputs.
f DSKPVW1, DSKPVW2: Outputs DSK preview signals.
Follow the setting of the <SYS> button on the top menu → [MAIN FRAME] → [DSK] tab → [Config] column → [DSK1] to [DSK4], and assign the signal
to either DSKPVW1 or DSKPVW2 line.
Keyers set to [Off] using the <SYS> button on the top menu → [MAIN FRAME] → [DSK] tab → [DSK PVW] column are not combined.
f DSK1CLN, DSK2CLN, DSK3CLN, DSK4CLN: Outputs clean signal before adding key effects from each keyer. It can also be switched to preview
image of each DSK.
f SEL KEYPVW: Outputs the preview for the key for pressed <KEY1> to <KEY4> buttons in the KEY operation area of each ME, and <DSK1> to
<DSK4> buttons. The image combined with the key where the <SYS> button on the top menu → [MAIN FRAME] → [Sel KeyPVW] tab → [ME1]/
[ME2]/[DSK] column is set to [On] is output. If the button for the key set to [Off] is selected, the image is output without the key combined.

Adjusting the luminance key/linear key

Adjust the luminance key and linear key definition.
1
Select the <DSK MISC> button → [DSK1] to [DSK4] → [Setting] tab.
2
Set [Clip], [Gain], and [Density] in the [DSK Adjust] column.
[Clip]
[Gain]
[Density]
3
Select an item in [Invert] in the [DSK Adjust] column.
[Off]
[On]
Chapter 5 Basic Operations — DSK (Downstream key)
Disables the transition mode of key in or key out.
Enables the transition mode of key in or key out.
Sets the [In Type] column and the [Out Type] column separately.
The [In Type] column setting becomes the same as the [Out Type] column setting.
Sets the reference level for creating key signals.
Sets the key amplitude.
Sets the key density.
Does not invert the key signals generated internally.
Inverts the key signals generated internally.
– 77 –