Color Corrector; Setting The Color Corrector; Initializing The Color Corrector; Copying The Setting - Panasonic AV-HS6000 Series Operation Manual

Color corrector

The unit can correct the colors of video signals because its terminals <SDI IN 25> to <SDI IN 32>, and <SDI OUT 13> to <SDI OUT 16> are equipped
with the color corrector function.

Setting the color corrector

1
Select the <IN OUT> button → [C/C IN 25‑30], [C/C IN 31‑32], [C/C OUT] → the tab to be set.
f Select the tab to be set from the [SDI IN 25] tab to [SDI IN 32] tab, or the [SDI OUT 13] tab to [SDI OUT 16] tab.
2
Select an item in [Enable] in the [Operation] column.
[On]
[Off]
3
Select an item in [Limit] in the [Operation] column.
[Off]
[108]
[104]
[100]

Initializing the color corrector

1
Select the <IN OUT> button → [C/C IN 25‑30], [C/C IN 31‑32], [C/C OUT] → the tab to be set.
f Select the tab to be set from the [SDI IN 25] tab to [SDI IN 32] tab, or the [SDI OUT 13] tab to [SDI OUT 16] tab.
2
Select an item in [Init Target] in the [Setting] column.
[Process]
[Tone]
[RGB Matrix]
[All]
3
Select [Initialize] in the [Setting] column.
f The corresponding item is initialized.

Copying the setting

1
Select the <IN OUT> button → [C/C IN 25‑30], [C/C IN 31‑32], [C/C OUT] → the tab to be set.
f Select the tab to be set from the [SDI IN 25] tab to [SDI IN 32] tab, or the [SDI OUT 13] tab to [SDI OUT 16] tab.
2
Select an item in [Copy Target] in the [Setting] column.
f Select the tab for the copy source of the setting.
3
Select [Copy From] in the [Setting] column.
f The setting of the selected tab is copied. However, the setting of the [Setting] column is not copied.

Process control

1
Select the <IN OUT> button → [C/C IN 25‑30], [C/C IN 31‑32], [C/C OUT] → the tab to be set.
f Select the tab to be set from the [SDI IN 25] tab to [SDI IN 32] tab, or the [SDI OUT 13] tab to [SDI OUT 16] tab.
2
Set [Y‑Gain], [Pedestal], [C‑Gain], and [Hue] in the [Process] column.
[Y‑Gain]
[Pedestal]
[C‑Gain]
[Hue]
3
Select an item in [Colorimetry] in the [Process] column.
f Set the colorimetry conversion for SD/HD conversion.
[On]
[Off]
Chapter 5 Basic Operations — Color corrector
Enables the color corrector of the relevant channel.
Disables the color corrector.
Does not restrict the color range of input signals.
Restricts the amplitude level of the colors (R, G, and B) to 0% to 108%.
Restricts the amplitude level of the colors (R, G, and B) to 0% to 104%.
Restricts the amplitude level of the colors (R, G, and B) to 0% to 100%.
Initializes the setting value in the [Process] column.
Initializes the setting values in the [Tone1 Black]/[Tone2 Gray L]/[Tone3 Gray H]/[Tone4 White] column.
Initializes the setting values in the [Matrix R/G]/[Matrix B] column.
Initializes all.
Sets the gain value of the Y signal.
Sets the value of the pedestal level (black level).
Sets the gain value of the saturation (Sat).
Sets the amount of change of the hue (Hue).
Converts the SD format to the HD format.
f To enable this item, set the system to HD mode, and set the <IN OUT> button on the top menu → [SDI IN] → [Frame
Buffer] tab → [Mode] in the [SDI IN 1] to [SDI IN 32] columns to [Dot by Dot] or [U/C].
Does not perform conversion.
– 86 –