Appendix B: Specifications; General Spec - Yamaha 02R96 Owner's Manual

260

Appendix B: Specifications

Appendix B: Specifications

General Spec

Number of scene memories
Sampling Frequency
Signal Delay
Fader
Fader Resolution
Total Harmonic Distortion
(CH INPUT to STEREO OUT)
(Input Gain=Min.)
Frequency Response
(CH INPUT to STEREO OUT)
Dynamic Range
(maximum level to noise level)
2
Hum & Noise
(20 Hz–20 kHz)
Rs=150
Input Gain=Max.
Input Pad =0 dB
Maximum Voltage Gain
Crosstalk
(@ 1 kHz)
Input Gain=Min.
AD Input (1–16: A/B)
AD Input (17–24)
Analog Input
(2TR IN ANALOG 1, 2)
02R96—Owner's Manual
Internal
External
1
fs=48 kHz
fs=96 kHz
Phantom switch
Pad switch
Gain control
Peak indicator
Signal indicator
Insert
Insert switch
AD converter
Gain control
Peak indicator
Signal indicator
AD converter
AD converter
99
44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
Normal rate: 44.1 kHz–10% to 48 kHz+6%
Double rate: 88.2 kHz–10% to 96 kHz+6%
Less than 2.0 ms CH INPUT to STEREO OUT (fs=48 kHz)
Less than 1.1 ms CH INPUT to STEREO OUT (fs=96 kHz)
100 mm motorized with touch sense
+10 to –96, – dB (256 steps/100 mm) input faders
0 to –130, – dB (256 steps/100 mm) master faders, stereo fader
Less than 0.05% 20 Hz to 20 kHz @ +14 dB into 600
Less than 0.01% 1 kHz @ +18 dB into 600
Less than 0.05% 20 Hz to 40 kHz @ +14 dB into 600
Less than 0.01% 1 kHz @ +18 dB into 600
20 Hz–20 kHz, 0.5, –1.5 dB @ +4 dB into 600
20 Hz–40 kHz, 0.5, –1.5 dB @ +4 dB into 600
110 dB typ. DA Converter (STEREO OUT)
105 dB typ. AD+DA (to STEREO OUT) @ fs=48 kHz
105 dB typ. AD+DA (to STEREO OUT) @ fs=96 kHz
–128 dB Equivalent Input Noise
–92 dB residual output noise. STEREO OUT (STEREO OUT off)
–92 dB (96 dB S/N) STEREO OUT (STEREO fader at nominal level and
all CH INPUT faders at minimum level)
–64 dB (68 dB S/N) STEREO OUTPUT (STEREO fader at nominal level
and one CH INPUT fader at nominal level)
74 dB CH INPUT (CH1–24) to STEREO OUT/OMNI (BUS) OUT
74 dB CH INPUT (CH1–24) to OMNI (AUX) OUT (via pre input fader)
74 dB CH INPUT (CH1–24) to CONTROL ROOM MONITOR OUT (via
STEREO bus)
–80 dB adjacent input channels (CH1–24)
–80 dB input to output
+48 V DC is supplied to A (XLR-3-31 type) input
0/26 dB attenuation
44 dB (–60 to –16), detented
LED (red) turns on when post HA level reaches 3 dB below clipping
LED (green) turns on when post HA level reaches 20 dB below nomi-
nal
I/O (pre AD converter)
on/off
24-bit linear, 128-times oversampling (fs=48 kHz)
44 dB (–34 to +10), detented
LED (red) turns on when post HA level reaches 3 dB below clipping
LED (green) turns on when post HA level reaches 20 dB below nomi-
nal
24-bit linear, 128-times oversampling (fs=48 kHz)
24-bit linear, 128-times oversampling (fs=48 kHz)
25
(fs=48 kHz)
(fs=96 kHz)