Champion DH6000T-VHR Installation Manual page 15

Shipping weight crated: 300 lbs.
5-3/4"
[145]
Min
Clearance
7-1/4"
[184]
4-11/16"
5-3/4"
5-3/4"
[146]
[146]
Inside Table
UTILITIES
1 Electrical Machine Connection
(See Electrical Box)
2 Hot Water 3/4" NPT Hot Water 110° - 140°F
20-22 PSI Flow Pressure
3 Drain 1.5" OD Connection; 15 GPM Max
Flow (Drain water tempering height 5")
4 Drain Water Tempering 1/2" Cold water
line with customer supplied cut-off valve
(optional)
5 Integrated Detergent System Detergent
bottle supply connections (optional)
68"
64-5/16"
[1727]
[1634]
Warning: Plumbing, electrical connections should be
48-7/8"
made by qualified personnel who will observe all the
72"
[1242]
applicable plumbing, sanitary and safety codes and the
[1829]
66-1/16"
National Electrical Code.
[1678]
3-9/16"
Note: Optional Drain Tempering: 1/2" NPT cold water [91]
connection required. 1/2" NPT drain connection from back flow
11-5/16"
preventer to house drain. (FIELD INSTALLED and PLUMBED). [288]
Due to an ongoing value analysis program at 3-9/16"
[91]
Champion, specifications contained in this catalog
are subject to change without notice.
11-5/16"
[288]
Champion Industries, Inc.,
3765 Champion Blvd., NC 27105
19-1/2"
336/661-1556 • Fax: 336/661-1979
ChampionIndustries.com
17-3/16"
[437]
72"
[1829]
4-3/8"
[110]
50-7/8"
[1293]
31-5/8"
[804]
Side View
[119]
18-7/16"
18-7/16"
[469] [469]
6-7/8"
6-7/8"
[175]
[175]
4-13/16"
4-13/16"
[122]
25-3/8"
[122] 6-1/16"
[645] [154]
6-1/16"
25-3/8"
Inside Table
[645] [154]
Flange
Flange
26-7/8"
Plan View
[683]
26-7/8"
[683]
Machine & Built-in Booster (Standard)
34-1/8"
[866]
208-240/60/1 77-68
34"
[863]
208-240/60/3 46-41
Machine Only
(two point electrical connection or no built-in booster)
208-240/60/1 38-34
208-240/60/3 25-23
33-5/8"
[853]
8-9/16"
[217]
Booster Only (two point electrical connection)
6-1/4"
[159]
33-5/8"
[853]
19-1/2"
8-9/16"
[496]
[217]
208-240/60/1 39-34
4-7/16"
[112]
6-1/4"
208-240/60/3 21-18
[159]
[496] Note: Water Hammer Arrestor (meeting ASSE-1010 standard or equivalent)
4-7/16"
to be supplied (by others) in common water supply line at service connection.
[112]
25-3/8"
[645]
Inside Table
Flange
26-7/8"
[683]
34"
[863]
66-1/16"
[1678]
3-9/16"
[91]
11-5/16"
[288]
19-1/2"
Front View [496]
Corner Table
Configuration
Rated Minimum Supply
Voltage Amps Circuit Ampacity
Rinse
100
Pressure
Rinse Aid
60
Gauge
Rinse Injection
Pressure
480/60/3 20 30 1/8" NPT
Rinse Aid
Gauge
Injection
1/8" NPT
Minimum
Rated Supply Circuit
Voltage Amps Ampacity
Detergent
50
Injection
7/8" Dia
30
Detergent
Injection
Detergent
480/60/3 11 15
Probe
7/8" Dia
7/8" Dia
8-5/16"
Minimum
[212]
Rated Supply Circuit
Voltage Amps Ampacity
Detergent
50
Probe
7/8" Dia
25
480/60/3 9 15
an Ali Group Company
6-7/8"
[175]
4-13/16"
[122]
DH6000
6-1/16"
[154]
Hood-type Dishwashing Machine
Dimensions shown in inches and [mm]
33-5/8"
[853]
8-9/16"
[217]
6-1/4"
[159]
4-7/16"
[112]
6" [152]
to Inside
Tank Wall
1-1/8"
8-1/8" [207]
to Rack
Guide
Typical Table Construction
SPECIFICATIONS
Maximum
Overcurrent Capacities
Protective Device
Racks per hr. (NSF rated)
100
Wash tank (gal.)
60
Motor horsepower
Water consumption
30
Gal. per hr. (max. use)
Gal. per rack
Temperature °F
Maximum
Wash
Overcurrent
Rinse
Protective Device
Heating
50
Tank heat, electric
30
Electric Booster
15
Selectable cycle
Maximum
Overcurrent
times in minutes
Protective Device
Time cycles in seconds
50
Wash
25
Rinse
15
Sanitary Dwell
Total
Specification Sheet
High Temperature
Rinse
Pressure
Rinse Aid
Gauge
Injection
1/8" NPT
Detergent
Injection
7/8" Dia
Detergent
Probe
7/8" Dia
Side View
30"
[762]
7-1/4" [184]
1-1/2" [32] Roll
21-3/8"
[543]
[29]
60
10
2 HP
39
0.73
150
180
5.2 kW
7.5 kW
Dish- Pot &
washer Pan
Mode Mode
1 2 4 6
36 94 214 334
8 10 10 10
16 16 16 16
60 120 240 360
xi