Champion DH6000T-VHR Installation Manual page 13

DH6000-VHR
with Ventless Heat-Recovery and Condensate
Removal
Shipping weight crated: 350 lbs.
VENTLESS/HEAT RECOVERY/CONDENSATE REMOVAL
5-3/4"
[145]
Min
Clearance
31-5/8"
[804]
4-11/16"
Side View
[119]
30"
[762]
1-1/2" [32] Roll
21-3/8"
[543]
1-1/8"
[29]
Typical Table Construction
UTILITIES
1 Electrical Machine Connection
(See Electrical Box)
2 Cold Water 3/4" NPT Cold Water 50° - 75°F
45 PSI Min Incoming (20-22 PSI flow)
3 Drain 1.5" OD Connection; 15 GPM Max
Flow (Drain water tempering height 5")
4 Drain Water Tempering 1/2" Cold water
line with customer supplied cut-off valve
(optional)
5-3/4"
[145]
Min
5 Integrated Detergent System Detergent
5-3/4"
Clearance
[145]
bottle supply connections (optional)
Min
Clearance
17-13/16"
Warning: Plumbing, electrical connections should be
[437]
7-1/4"
made by qualified personnel who will observe all the
[184]
applicable plumbing, sanitary and safety codes and the
4-3/8"
National Electrical Code.
[111]
50-7/8"
31-5/8"
Note: Optional Drain Tempering: 1/2" NPT cold water
[804]
connection required. 1/2" NPT drain connection from back flow
preventer to house drain. (FIELD INSTALLED and PLUMBED).
31-5/8"
[804]
Due to an ongoing value analysis program at
Champion, specifications contained in this catalog
4-11/16"
[119]
are subject to change without notice.
Champion Industries, Inc., 4-11/16"
[119]
3765 Champion Blvd., NC 27105
336/661-1556 • Fax: 336/661-1979
ChampionIndustries.com
78-13/16"
17-13/16"
[2003]
[437]
72"
[1829]
4-3/8"
[111]
50-7/8"
[1293]
Front View
5-3/4"
[146]
7-1/4" [184]
Machine & Built-in Booster (Standard)
Voltage
208-240/60/1 77-68
208-240/60/3 46-41
480/60/3
Machine Only
(two point electrical
15-5/16"
[389]
Voltage
78-13/16"
68"
64-5/16"
[2003]
[1727] 208-240/60/1 38-34
[1634]
3-1/16"
[78]
72" 70"
208-240/60/3 25-23
48-7/8"
[1778]
[1829]
[1242]
480/60/3
3-9/16"
[1293]
Booster Only (two point electrical connection)
3-9-16"
[91]
Voltage
11-5/16"
208-240/60/1 39-34
[288]
208-240/60/3 21-18
480/60/3
Note: Water Hammer Arrestor (meeting ASSE-1010 standard or equivalent)
to be supplied (by others) in common water supply line at service connection.
5-3/4"
[146]
25-3/8"
[645]
Inside Table
Flange
26-7/8"
[683]
34"
[863]
70"
[1778]
3-9-16"
[91]
11-5/16"
[288]
77-1/4" 19-1/2"
[1963] [496]
Hood
Up
41-3/8"
[1052]
18-7/16"
5-3/4"
[469]
18-1/8"
[146]
18-7/16"
[549]
[469]
6-7/8"
[175]
8-3/4"
6-7/8" [221]
[175]
4-13/16"
[122]
25-3/8"
[645] 4-13/16"
Inside Table [122]
6-1/16"
25-3/8"
Flange
[645]
Inside Table
26-7/8"
Plan View
Flange
[683]
26-7/8"
[683]
Rated Minimum Supply Overcurrent
Amps Circuit Ampacity Protective Device
100
34"
34-1/8"
[863]
[866]
60
20 30
connection)
Minimum
Rated Supply Circuit Overcurrent
Amps Ampacity Protective Device
50
30
11 15
8-9/16"
[91]
[217]
6-1/4"
Minimum
11-5/16"
[159]
8-9-16"
[288]
Rated Supply Circuit Overcurrent
[217]
Amps Ampacity Protective Device
6-1/4"
19-1/2"
[159]
[496] 50
4-7/16"
[112]
25
19-1/2"
[496]
9 15
4-7/16"
[112]
an Ali Group Company
18-7/16"
[469]
6-7/8"
[175]
4-13/16"
[122]
6-1/16"
[154]
Dimensions shown in inches and [mm]
8-9-16"
[217]
6-1/4"
[159]
3-7/8"
[97]
Side View
4-7/16"
[112]
8"
[203]
33-3/4"
[857]
4-3/4"
[122]
17"
6"
[432]
[152]
Corner Table
6-1/16"
[154]
Configuration
31"
[787]
[154]
34-1/8"
[867]
SPECIFICATIONS
Capacities
Maximum
Racks per hr. (NSF rated)
Wash tank (gal.)
100
Motor horsepower
Rinse
60
Water consumption
Pressure
Gauge
30
Gal. per hr.
Gal. per rack
Temperature °F
Wash
Maximum
Rinse
Heating
Tank heat, electric
50
Electric Booster
30
15
33-5/8"
[853]
Selectable cycle
Maximum times in minutes
Time cycles in seconds
Wash
50
Rinse
25
Sanitary Dwell
15
Vent Fan
Total
Specification Sheet
3/8"
8-3/8"
[9]
[214]
From Wall
30"
[764]
Table
20-1/8"
Typ
[511]
Rinse Aid
Injection
1/8" NPT
INSIDE TRACKS
Detergent
Injection
7/8" DIA
Detergent
Probe
7/8" DIA
69-3/4"
[1770]
4-3/8"
[112]
37-7/8"
[963]
14-1/8"
[359]
6" [152]
to Inside
Tank Wall
8-7/8"
[225]
19-5/8"
[500]
8-1/8" [207]
to Rack
Guide
40
10
2 HP
Rinse Aid
Rinse Aid
Injection 29
Injection
1/8" NPT
1/8" NPT 0.73
150
180
5.2 kW
Detergent
7.5 kW
Injection
7/8" Dia
Dish- Detergent Pot &
Injection
Detergent
washer Pan
7/8" DIA
Probe
Mode Mode
7/8" Dia
Detergent
1 2 4 6
Probe
8-5/16"
7/8" DIA
[212]
36 94 214 334
8 10 10 10
16 16 16 16
30 30 30 30
90 150 270 390
ix
20-1/8"
[511]
29-1/2"
[749]
26-1/8"
[663]