Champion DH6000T-VHR Installation Manual page 11

Shipping weight crated: 300 lbs.
5-3/4"
[146]
UTILITIES
1
2
3
4
15-5/16"
[389] 5
15-5/16"
68"
[389]
[1727]
3-1/16"
7-1/4"
Warning: Plumbing, electrical connections should be
[78] 68"
[184]
64-5/16"
48-7/8" made by qualified personnel who will observe all the
[1727]
[1634]
3-1/16"
[1242]
applicable plumbing, sanitary and safety codes and the
[78]
48-7/8"
National Electrical Code.
31-5/8" [1242]
[804]
Note: Optional Drain Tempering: 1/2" NPT cold water
connection required. 1/2" NPT drain connection from back flow
3-9/16"
[91]
preventer to house drain. (FIELD INSTALLED and PLUMBED).
Due to an ongoing value analysis program at Champion,
/16"
19]
specifications contained in this catalog are subject to
change without notice.
Champion Industries, Inc.,
3765 Champion Blvd., NC 27105
336/661-1556 • Fax: 336/661-1979
ChampionIndustries.com
5-3/4"
[145]
Min.
Clearance
27"
90-15/16"
[686]
26-1/8"
60"
[664]
[1524]
7-1/4"
[184]
31-5/8"
[804]
4-11/16"
[119]
18-7/16"
5-3/4"
[146] 18-7/16"
[469]
6-7/8"
[175]
25-3/8"
4-13/16"
[645]
[122]
25-3/8"
Inside Table
[645]
Flange
Inside Table
Flange
26-7/8"
Plan View
[683]
26-7/8"
[683]
Electrical Machine Connection
(See Electrical Box)
Hot Water 3/4" NPT Hot Water 110° - 140°F
20-22 PSI Flow Pressure
34-1/8"
[866]
Drain 1.5" OD Connection; 15 GPM Max
34-1/8"
[866]
Flow (Drain water tempering height 5")
Drain Water Tempering 1/2" Cold water
line with customer supplied cut-off valve
(optional)
Integrated Detergent System Detergent
bottle supply connections (optional)
64-5/16"
[1634]
3-9/16"
8-9/16"
[91]
[217]
33-5/8"
[853]
8-9/16"
11-5/16"
[288] [217]
6-1/4"
11-5/16"
[159]
19-1/2"
[288]
[496]
4-7/16"
[112]
19-1/2"
[496]
4-7/16"
[112]
5-3/4"
[146]
Side Front View
View
[2309]
5"
[128]
68-15/16"
[1752]
3-9/16"
[91]
11-5/16"
[288]
[469]
6-7/8"
[175]
4-13/16"
[122]
6-1/16"
[154]
6-1/16"
Corner Table
[154]
Configuration
Machine & Built-in Booster (Standard)
Rated Minimum Supply
Voltage Amps Circuit Ampacity
Rinse
208-240/60/1 77-68
Pressure
208-240/60/3 46-41
Rinse
Gauge
Pressure
480/60/3 20
Gauge
Machine Only
(two point electrical connection or no built-in booster)
Rated
Voltage Amps
208-240/60/1 38-34
208-240/60/3 25-23
480/60/3 11
33-5/8"
[853]
Booster Only (two point electrical connection)
6-1/4"
[159]
Rated
Voltage Amps
8-5/16"
[212]
208-240/60/1 39-34
208-240/60/3 21-18
480/60/3 9
Note: Water Hammer Arrestor (meeting ASSE-1010 standard or equivalent)
to be supplied (by others) in common water supply line at service connection.
18-7/16"
[469]
6-7/8"
[175]
4-13/16"
[122]
6-1/16"
25-3/8"
[645] [154]
Inside Table
Flange
26-7/8"
[683]
33-15/16"
[862]
8-9/16"
[217]
6-1/4"
[159]
19-1/2"
[496]
4-7/16"
[112]
6" [152]
to Inside
6" [152]
Tank Wall
to Inside
Tank Wall
8-1/8" [207]
to Rack
8-1/8" [207]
Guide
to Rack
Guide
Maximum
Overcurrent
Protective Device
100 100
Rinse Aid
60 60
Injection
Rinse Aid 30 1/8" NPT 30
Injection
1/8" NPT
Minimum Maximum
Supply Circuit Overcurrent
Ampacity Protective Device
Detergent
50 50
Injection
7/8" Dia
Detergent
30 30
Injection
Detergent
7/8" Dia 15 15
Probe
7/8" Dia
Detergent
Probe
7/8" Dia
8-5/16"
Minimum Maximum
[212]
Supply Circuit Overcurrent
Ampacity Protective Device
50 50
25 25
15 15
Specification Sheet
DH6000T
DH6000T High Temperature
Hood-type Dishwashing Machine
Dimensions shown in inches and [mm]
Side
View
Rinse Aid
Injection
1/8" NPT
Detergent
Injection
7/8" DIA
Detergent
Probe
7/8" DIA
8-5/16"
[212]
30"
[762]
7-1/4" [184]
1-1/2" [32] Roll
21-3/8"
[543]
1-1/8"
[29]
Typical Table Construction
SPECIFICATIONS
Capacities
Racks per hr. (NSF rated)
Wash tank (gal.)
Motor horsepower
Water consumption
Gal. per hr. (max. use)
Gal. per rack
Temperature °F
Wash
Rinse
Heating
Tank heat, electric 5.2 kW
Electric Booster 7.5 kW
Dish- Pot &
washer Pan
Mode Mode
Selectable cycle
1 2 4
times in minutes
Time cycles in seconds
Wash 36 94 214
Rinse 8 10 10
Sanitary Dwell 16 16 16
60 120 240 360
Total
vii
60
10
2 HP
39
0.73
150
180
6
334
10
16