Extron electronics FOX II T DP 4K User Manual page 32

Command and Response Table for Receiver SIS Commands (continued)
Command
Audio mute
Mute the audio
Example:
Unmute the audio
Show audio mute status
Video Bit Depth
Set video bit depth to auto
Set video bit depth to 8-bit
View video bit depth
Receiver name
Assign a name to the device
Reset device name to default
View the device name
Status requests
View Rx link (Tx-to-Rx) status
View input video status
View audio input status
View HDCP status
View temperature
Information requests
Information request
Show firmware version
Example:
Request HDCP Output
Status
Request part number
Request SFP status
Resets
Reset audio
System reset
KEY: X% = Video bit depth
X1) = Audio mute
X1@
= Receiver name
X1# = Link and input status
X1$ = Audio output
X1%
= Sink and output HDCP signal
X1^
= Internal temperature
X1(
= Firmware version
X2)
= Optical module manufacturer
X2!
= Tx or Rx power
X2@
= Operating temp of module
X2#
= HDCP Output Status
SIS Command Response
(host to unit) (unit to host)
X1) X1)
*1Z Amt
1*1Z Amt1*1
X1) X1)
*0Z Amt
X1$ Z X$]
E }
V0BITD BitdV0
E }
V1BITD BitdV1
E } X%]
VBITD
EX1@ }
CN Ipn•
E }
•CN Ipn•FOX-II-R-DP-4K
E CN } X1@]
X1#]
2S
X1#]
4S
5S X1#]
6S X1%]
20S X1^ F•
I 1Lnk
X1(]
Q
Q 1.23
E }
OHDCP HdcpO
N
60– nnnn
40S X2) • X2!
E } ]
ZA Zpa
E } ]
ZXXX Zpx
0 = auto mode (default)
0 = mute all (output DisplayPort and analog)
1 = mute DisplayPort only
Up to 24 alphanumeric characters and hyphen (–) No spaces are allowed, and there is no
distinction between upper and lower case.
0 = link or input not detected
1 = digital
0 = no source detected
1 = source detected with HDCP
2 = source detected but no HDCP present
nnnF•nnC
v.vv
Up to 16 alphanumeric characters
xx.x dBm
nnn.n
0 = no sink
FOX II T/R DP 4K Transmitter and Receiver • Remote Control
Additional description
] Silence the receiver DisplayPort audio.
*1
] Silence the DisplayPort audio.
] The transmitter outputs DisplayPort audio, analog
*0
audio, or both.
Mute status of
] Follow the input bit depth.
] Force 8-bit depth.
X1@]
Name the receiver
]
Report the status of the HDCP encoding on the
output.
X1^ C ] Show temperature in degrees Fahrenheit and
Celsius.
X1# X1# X1# X1#
•SigI •HdcpO •AudO
The unit responds with the current status (light
detected) of optical link 1, the digital input (signal
detected), the HDCP status of the output, and the
output audio; and the device type (Rx).
] The factory-installed firmware version is 1.23
(sample value only).
X2#] Show HDCP detected on the receiver output.
] See the Extron website, www.extron.com, for
– nn
part numbers.
Tx • X2! Rx • X2@]
Reset the return audio gain and attenuation to 0 dB.
Reset all settings to factory defaults.
1 = 8-bit
1 = HDCP sink
X1$ audio is X$ .
X1@
.
]
•RX
2 = mute analog only
1 = link or input detected
2 = analog
2 = non-HDCP sink
24