Eaton MP-3000 Instruction Leaflet page 23

SUB- LINE # DISPLAY
MENU
PaGE 9, SP aUX 1 SETTINGS fOR aUX 1 RELay OUTPUT CONfIGURaTION
1 LSPU XXX
2 LSDO XXX
3 LSDL XX
4 Choose:
GF A ON
GFT ON
or
GF OFF
5 Choose:
I2T A ON
I2T T ON
or
I2T OFF
6 Choose:
JAM A ON
JAM T ON
or
JAM OFF
7 Choose:
UL A ON
UL T ON
or
UL OFF
8 Choose:
UB A ON
UB T ON
or
UB OFF
9 Choose:
WD A ON
WD T ON
or
WD OFF
10 Choose:
MB A ON
MB T ON
or
MB OFF
11 Choose:
LB A ON
LB T ON
or
LB OFF
12 Choose:
AX A ON
AX T ON
or
AX OFF
13 Choose:
SX A ON
SX T ON
or
SX OFF
14 Choose:
TBS T ON
or
TBS OFF
15 RTDF ON
or
RTDF OFF
MP-3000
Table 4.3 View Setting Mode/Program Worksheet.
HELP MESSAGE
LOAD SHED PICK-UP CURRENT AS
% OF FLA
LOAD SHED DROP-OUT CURRENT AS
% OF FLA
LOAD SHED DELAY IN SECONDS
ENABLE GROUND FAULT ALARM OR
TRIP TO ACTIVATE AUX1 RELAY
OUTPUT OR DISABLE
ENABLE I2T ALARM OR TRIP TO
ACTIVATE AUX1 RELAY OUTPUT OR
DISABLE
ENABLE JAM ALARM OR TRIP TO
ACTIVATE AUX1 RELAY OUTPUT OR
DISABLE
ENABLE UNDERLOAD ALARM OR TRIP
TO ACTIVATE AUX1 RELAY OUTPUT
OR DISABLE
ENABLE PHASE UNBALANCE ALARM
OR TRIP TO ACTIVATE AUX1 RELAY
OUTPUT OR DISABLE
ENABLE WINDING TEMP ALARM OR
TRIP TO ACTIVATE AUX1 RELAY
OUTPUT OR DISABLE
ENABLE MOTOR BEARING ALARM
OR TRIP TO ACTIVATE AUX1 RELAY
OUTPUT OR DISABLE
ENABLE LOAD BEARING ALARM OR
TRIP TO ACTIVATE AUX1 RELAY
OUTPUT OR DISABLE
ENABLE AUXILIARY RTD TEMP ALARM
OR TRIP TO ACTIVATE AUX1 RELAY
OUTPUT OR DISABLE
ENABLE STARTS PER TIME TRIP OR
ALARM TO ACTIVATE AUX1 RELAY
OUTPUT OR DISABLE
ENABLE TIME BETWEEN STARTS TRIP
TO ACTIVATE AUX1 RELAY OUTPUT OR
DISABLE
ENABLE INDIVIDUAL RTD CHANNEL
FAILURE TO ACTIVATE AUX1 RELAY
OUTPUT OR DISABLE
www.eaton.com
SETTING RANGE/VALUE
(DEfaULT SELECTION aND
VaLUE aS ShIPPED IN BOLD)
Off
50-150%, (1% increments)
NOTE: P9L1 and P9L2 are forced to be
coherent. Refer to Section 5 for details.
Off
50-LSPU Value %, (1% increments)
NOTE: P9L1 and P9L2 are forced to be
coherent. Refer to Section 5 for details..
0-5 sec. (0.1 sec. increments)
If LSPU and LSDO are both set to OFF, the
following SP AUX1 functions are available and
(1)
visible.
Toggles between GF A ON, GF T ON, and
Gf Off
I2T T ON
Toggles between I2T A ON, , and
I2T OFF
Toggles between JAM A ON, JAM T ON, and
jaM Off
Toggles between UL A ON, UL T ON, and
Off
Toggles between UB A ON, UB T ON, and
UB Off
Toggles between WD A ON, WD T ON, and
WD Off
Toggles between MB A ON, MB T ON, and
MB Off
Toggles between LB A ON, LB T ON, and
LB Off
Toggles between AX A ON, AX T ON, and
aX Off
Toggles between SX A ON, SX T ON, and
SX Off
TBS Off
Toggles between TBS T ON and
RTDf Off
Toggles between RTDF ON and
IM02602002E
VALUE SELECTED
UL
Page 4-11