AT&T Lucent Technologies PARTNER Plus Installation And Use Manual page 44

System Programming Reference (cont'd)
LINES
DIAL MODE
Identifies information lines as touch-tone or
rotary. You may also need to adjust the
Rotary Dialing Timeout (#108).
DIAL #201
DIAL a line number
DIAL 1=Touch-Tone
2=Rotary
PRESS [Next Item] to program another line
HOLD DISCONNECT TIME
Selects the signal that the system uses to
detect when a caller on hold hangs up.
Change the setting to "long" if the system
disconnects callers on hold before they
hang up, or to "short" if user gets a dial tone
when trying to retrieve calls on hold.
DIAL #203
DIAL a line number
DIAL 1=Long (450 msec)
2= Short (50msec)
PRESS [Next Item] to program another line
Factory Setting
=
LINE ASSIGNMENT
Assigns the outside lines that are available
at an extension, in consecutive order. The
order of line assignment is from left to
right, starting with the bottom row of line
buttons on a system phone. To put the
lines in a different order, first use this
procedure to unassign all lines; then
assign lines in the desired order (as you
assign each line, it goes onto the first
available button).
DIAL #301
DIAL an extension number
DIAL a line number (1 to 8)
DIAL 1=Assigned
2=Not Assigned
2 lines per 200 or 206 module
PRESS [Next Item] to assign another line to
this extension
To program another extension:
PRESS [Next Procedure] [Prev Procedure], enter a
new extension number, and repeat
above steps
LINE ACCESS RESTRICTION
RESTRICTS CALLING ON INDIVIDUAL LINES
Assigned to an Extension.
DIAL #302
DIAL an extension number
DIAL a line number
DIAL 1=No Restriction
2=Outgoing Only
3=Incoming Only
4=No Access (line appears on
button to see line status, but
can use line only to join a call
or to pick up a transferred or
held call)
PRESS [Next Item] to program another line
To program another extension:
PRESS [Next Procedure] [Prev Procedure], enter a
new extension number, and repeat
above steps
DISPLAY LANGUAGE
Identifies the language used in display
messages on an MLS-12D or MLS-34D
phone at the extension.
DIAL #303
DIAL an extension number
DIAL 1=English
2=Spanish
3=French
PRESS [Next Item] to program another
extension
AUTOMATIC EXTENSION PRIVACY
Prevents other extensions from joining a
call on a specified extension. For example,
use this procedure to prevent users from
interrupting calls on a extension with a
fax machine or modem.
DIAL #304
DIAL an extension number
DIAL 1=Assigned
2= Not Assigned
PRESS [Next Item] to program another
extension
EXTENSIONS
ABBREVIATED RINGING
Determines whether a call rings repeat-
edly at an extension when the extension is
busy on another call. If Abbreviated
Ringing is on and you are busy on a call,
the call rings once; the green button for
the line continues to flash until you answer
the call or the caller hangs up.
DIAL #305
DIAL an extension number
DIAL 1=Active (On—1 ring)
2=Not Active (Off—repeated
ringing)
PRESS [Next Item] to program another
extension
TRANSFER RETURN EXTENSION
Identifies where transfered calls should
go if the extension receiving the transfer
does not answer. (Useful for extensions
with auto attendants, so the caller only
hears the device's greetings once.)
DIAL #306
DIAL an extension number
DIAL number of the extension to which
call should return if not answered
Extension transfering the call
PRESS [Next Item] to program another
extension
COPY SETTINGS
Copies the following settings from one
extension to another:
#301 Line Assignment
#302
Line Access Restriction
#303
Display Language
#304 Automatic Privacy
#305
Abbreviated Ringing
#306 Transfer Return Extension
#401
Outgoing Call Restriction
#405 Disallowed List Assignment
#408
Allowed List Assignment
#501
Pickup Group Extensions
#502
Calling Group Extensions
#504
Night Service Group
#601
Fax Machine Extensions
#607
Auto Attendant/VMS Extensions
Automatic Line Selection
Line Ringing
DIAL #399
DIAL a source extension number
DIAL a target extension number
Factory Setting
=
Programming 3-15