Measurement; Performing Measurement - Konica Minolta CA-410 Instruction Manual

Measurement

Before starting measurement, perform the following.
Connection (P. 58)
Measurement
(P. 65)
Preparation
Settings (P. 106)

1. Performing Measurement

Operating Procedure
1
Press the [CAL CH] key to select a probe
and a calibration channel. (Not required
in flicker mode)
(1) Press the [CAL CH] key.
(2) Press the [UP]/[DOWN] key to select
a probe (01 to 10) and then press the
[ENTER] key.
(3) Press the [UP]/[DOWN] key to select
a calibration channel (CH00 to 99),
and then press the [ENTER] key.
The calibration coefficient for the selected
calibration channel is applied.
2
Place the probe flat against the display
and perform measurement.
The measurement results will be displayed in the
selected data display area.
Connect the power cable and turn ON the power.
Perform preparations (instrument setting, zero calibration) that are required prior to
measurement.
Set up the instrument according to the setting method.
This is not necessary if the instrument has already been set up or if measurement will
be performed using Konica Minolta's calibration standard.
m RGB+W matrix calibration
101
Select User Calb CH
Select Probe
C H 0 0 1 6 0 . 0 0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
01
C H 0 1 1 6 0 . 0 0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
02
C H 0 2 1 6 0 . 0 0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
03
C H 0 3 1 6 0 . 0 0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
04
C H 0 4 1 6 0 . 0 0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
05
C H 0 5 1 6 0 . 0 0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
06
C H 0 6 1 6 0 . 0 0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
07
C H 0 7 1 6 0 . 0 0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
08
C H 0 8 1 6 0 . 0 0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
09
C H 0 9 1 6 0 . 0 0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
10
Select User Calb CH
Select Probe > Select CH
01 ◉ C H 0 0 1 6 0 . 0 0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
○ C H 0 1 1 6 0 . 0 0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
○ C H 0 2 1 6 0 . 0 0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
○ C H 0 3 1 6 0 . 0 0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
○ C H 0 4 1 6 0 . 0 0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
○ C H 0 5 1 6 0 . 0 0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
○ C H 0 6 1 6 0 . 0 0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
○ C H 0 7 1 6 0 . 0 0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
○ C H 0 8 1 6 0 . 0 0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
○ C H 0 9 1 6 0 . 0 0 . 3 1 0 0 0 . 3 1 2 9 a b c d e f g f
f KM factory calibration value
User calibration
c
(with set correction coefficients)
s Single-point calibration
Calibration Value
"----"
"----"
Single-point
calibration value
White calibration value