Konica Minolta CA-410 Instruction Manual page 48

Display Screen
(2) Settings area
Contains shortcut key icons for saving and setting measurement data.
Shortcut keys in the setting area are not displayed on screens other than the measurement screen (such as the menu
screen).
The setting area is enabled only in hold mode. (Single-probe measurement screen and multi-probe measurement screen)
Measuring
Measuring
160.00
01
Lv
02
cd/ ㎡
03
0.3127
04
x
05
06
0.3293
07
08
y
09
10
Save Meas Speed: LTD.AUTO Sync: MANU. (100. 0ms)
Use the [LEFT/RIGHT] keys to select a shortcut key icon.
Use the [UP/DOWN] key to move selection targets, including the data display area.
Press the [ENTER] key to apply the setting.
Measurement speed:
Sync Mode:
Data Save:
How to Save Data
1
Press the [ENTER] key to display the
screen for selecting where to save data.
Select the destination using the [UP/
DOWN] keys, and then press the [ENTER]
key.
The screen is not displayed when Save Destination is
set to AUTO. In this case, go to step 2.
2
During saving, a pop-up screen is
displayed indicating that data is being
saved.
If data already exists, a confirmation message
appears first asking whether it is OK to overwrite.
Select "Yes" using the [LEFT/RIGHT] key and press
the [ENTER] key.
* Data will be saved as absolute values even when the difference display is selected when saving is performed.
Trigger mode 0-cal AUTO
y
1.0
0.8
0.6
0.4
0.2
0.0 0.2 0.4 0.6 0.8 1.0 x
Φ10 Mini Normal
CH-01 f:Factory
ID: abcdefghij
Displays the measurement speed setting. Select this using the [UP/DOWN] and [LEFT/
RIGHT] keys, and then press the [ENTER] key to display the measurement speed menu.
(The menu for selecting AUTO/LTD.AUTO/FAST/SLOW is displayed)
Displays the synchronization mode setting. Select this using the [UP/DOWN] and [LEFT/
RIGHT] keys, and then press the [ENTER] key to display the synchronization mode menu.
(The menu for selecting NTSC/PAL/UNIV./INT[***.*Hz]/ EXT/MANU.[****.*msec] is
displayed. *** is the currently set value).
However, the mode is switched to UNIV. if the external trigger mode is turned ON in EXT
mode.
Select this using the [UP/DOWN] and [LEFT/RIGHT] keys, and then press the [ENTER] key to
save the displayed measurement results.
Hold
Enabled in
hold mode
46
Hold
160.00
01
Lv
02
cd/ ㎡
03
0.3127
04
x
05
06
0.3293
07
08
y
09
10
Save Meas Speed: LTD.AUTO Sync: MANU. (100. 0ms)
Select Save CH
D ATA 0 0 1 2 0 1 7 / 0 1 / 0 1 0 0： 0 0： 0 0
D ATA 0 0 2 2 0 1 7 / 0 1 / 0 1 0 0： 0 0： 0 0
D ATA 0 0 3 2 0 1 7 / 0 1 / 0 1 0 0： 0 0： 0 0
D ATA 0 0 4 2 0 1 7 / 0 1 / 0 1 0 0： 0 0： 0 0
D ATA 0 0 5 2 0 1 7 / 0 1 / 0 1 0 0： 0 0： 0 0
D ATA 0 0 6 2 0 1 7 / 0 1 / 0 1 0 0： 0 0： 0 0
D ATA 0 0 7 2 0 1 7 / 0 1 / 0 1 0 0： 0 0： 0 0
D ATA 0 0 8 2 0 1 7 / 0 1 / 0 1 0 0： 0 0： 0 0
D ATA 0 0 9 2 0 1 7 / 0 1 / 0 1 0 0： 0 0： 0 0
D ATA 0 1 0 2 0 1 7 / 0 1 / 0 1 0 0： 0 0： 0 0
Select Save CH
Data Save
D ATA 0 0 1 2 0 1 7 / 0 1 / 0 1 0 0： 0 0： 0 0
D ATA 0 0 2 2 0 1 7 / 0 1 / 0 1 0 0： 0 0： 0 0
D ATA 0 0 3 2 0 1 7 / 0 1 / 0 1 0 0： 0 0： 0 0
D ATA 0 0 4 2 0 1 7 / 0 1 / 0 1 0 0： 0 0： 0 0
Saving Data
D ATA 0 0 5 2 0 1 7 / 0 1 / 0 1 0 0： 0 0： 0 0
D ATA 0 0 6 2 0 1 7 / 0 1 / 0 1 0 0： 0 0： 0 0
D ATA 0 0 7 2 0 1 7 / 0 1 / 0 1 0 0： 0 0： 0 0
D ATA 0 0 8 2 0 1 7 / 0 1 / 0 1 0 0： 0 0： 0 0
D ATA 0 0 9 2 0 1 7 / 0 1 / 0 1 0 0： 0 0： 0 0
D ATA 0 1 0 2 0 1 7 / 0 1 / 0 1 0 0： 0 0： 0 0
Trigger mode 0-cal AUTO
y
1.0
0.8
0.6
0.4
0.2
0.0 0.2 0.4 0.6 0.8 1.0 x
Φ10 Mini Normal
CH-01 f:Factory
ID: abcdefghij