Table of Contents
Advertisement
1992-99 Pontiac Bonneville
Radio Removal:
1. Using a panel removal tool/screwdriver, carefully release the fastening clips from around the perimeter of
the radio trim bezel and remove the panel.
2.
Extract the three screws securing the radio to the dash, pull the radio from the cavity, unplug all the
connectors and remove the radio.
LEFT SIDE
"A1" BRACKET USE HOLE #4
LADO IZQUIERDA
"A1" SOPORTE USA
ABERTURA NO. 4
"A2" BRACKET USE HOLE #2
"A2" SOPORTE USA ABERTURA NO. 2
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1987-91 Pontiac Bonneville
Radio Removal:
1.
Place the gear selector in low gear to gain clearance.
2.
Gently pull on the edges of the radio panel to release the panel clips and remove the panel.
3.
Remove the two screws from the bracket above the radio.
4.
Remove one screw from the
rear support bracket (access
"D2" BRACKET
through the ashtray cavity).
USE HOLE #2
"D2" SOPORTE
5.
Insert a thin blade screwdriver
USA ABERTURA NO. 2
into the two slots below the
radio and pry the metal
retaining tabs upward to release
them.
6.
Slide the radio out of the cavity,
disconnect all the electrical
connections, then remove the radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1984-88 Pontiac Fiero
Radio Removal:
1. Remove the four screws from the radio trim panel.
2. Pull the panel up and outward toward the right.
3. Remove the four screws from the radio brackets and pull the radio out of the cavity.
4. Disconnect the antenna, speaker leads and all the electrical connections, then remove the radio.
LEFT SIDE
"A1" BRACKET USE HOLE #3
LADO IZQUIERDA
"A1" SOPORTE USA
ABERTURA NO. 3
3
3
"C2" BRACKET USE HOLE #3
"C2" SOPORTE USA ABERTURA NO. 3
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
RIGHT SIDE
"B1" BRACKET USE HOLE #2
LADO DERECHO
"B1" SOPORTE
USA ABERTURA NO. 2
FRONT OF KIT
FRENTE DE ESTUCHE
SPACER
ESPACIADOR
CUT OFF PINS (TWO SPACERS)
CORTA LAS CLAVIJAS
(DOS ESPACIADORES)
TOP
TOPE
CUT OFF TABS
(TWO BRACKETS)
ROMPE LAS LENGUETAS
(DOS SOPORTES)
RIGHT SIDE
"B1" BRACKET USE HOLE #4
LADO DERECHO
"B1" SOPORTE
USA ABERTURA
NO. 4
4
TRIM
BRACKET
FRONT OF KIT
4
CORTA EL
SOPORTE
FRENTE DE
ESTUCHE
"D2" BRACKET
USE HOLE #4
"D2" SOPORTE USA ABERTURA NO. 4
28
Read pages
1982-96 Oldsmobile Cutlass Ciera
3-7 for kit
assembly.
Radio Removal:
1.
Remove the ashtray from the mounting bracket.
2.
Extract the two screws from the padded portion of the dash in the ashtray location.
3.
Remove the single screw from the trim ring below the steering column and remove the trim.
4.
Remove the two screws from the top of the trim above the steering column and remove the trim.
5.
Carefully pry out each A/C vent, one on each side of the steering column.
6.
Remove the two screws from the left A/C vent location and one screw from the right A/C vent location.
7.
Carefully pry out the padded portion of the dash trim.
8.
Remove the four screws from inside the top edge of the instrument cluster trim and the four screws from
the bottom edge and remove the trim.
9.
Remove the four screws from the radio bracket/dummy panel; pull the radio out of the cavity, disconnect
the antenna, speaker leads and all the electrical connections. Then remove the radio.
"C2" BRACKET
USE HOLE #5
"C2" SOPORTE
Read pages
USA ABERTURA
3-7 for kit
NO. 5
assembly.
SPACER
ESPACIADOR
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
"B 2 " BRACKET
USE HOLE #2
"B 2 " SOPORTE
USA
ABERTURA
1984-88 Oldsmobile Cutlass
NO. 2
Radio Removal:
1.
Carefully pry outward on each corner of the radio trim panel to release the spring clips.
2.
Unscrew the cigarette lighter housing and remove the panel.
3.
Remove the four screws from the radio mounting bracket and pull the unit out of the cavity. Disconnect
the antenna, speaker leads and all the electrical connections, then remove the radio.
Read pages
3-7 for kit
"A1" BRACKET USE HOLE #3
assembly.
"A1" SOPORTE USA ABERTURA NO. 3
"A2" BRACKET
USE HOLE #3
"A2" SOPORTE
USA ABERTURA NO. 3
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
(FOUR BRACKETS) CUT OFF TABS
(4 SOPORTES) ROMPE EL LENGUENTE
TOP
TOPE
BOTTOM
"D2" BRACKET USE HOLE #1
FONDO
"D2" SOPORTE USA ABERTURA NO. 1
Supreme Classic
RIGHT SIDE
LEFT SIDE
LADO DERECHO
LADO IZQUIERDA
3
3
FRONT OF KIT
FRENTE DE ESTUCHE
25
Read pages
3-7 for kit
assembly.
"D1" BRACKET USE HOLE #2
"D1" SOPORTE USA ABERTURA NO. 2
"C1" BRACKET
USE HOLE #2
"C1" SOPORTE
USA
ABERTURA
NO. 2
Read pages
3-7 for kit
assembly.
"C2" BRACKET USE HOLE #3
"C2" SOPORTE USA
ABERTURA NO. 3
3
3
"B2" BRACKET
USE HOLE #3
"B2" SOPORTE
USA ABERTURA NO. 3
Advertisement
Table of Contents
