1997-99 Venture; Oldsmobile Achieva; 1985-91 Cutlass Calais; Silhouette - Scosche GM1503 Nstallation Instructions

1997-99 Chevrolet Venture
1997-99 Oldsmobile Silhouette
1997-99 Pontiac Trans Sport
Radio Removal:
1. Open ashtray and extract one from lower right side of dash bezel.
2. Open 12V socket cover and extract one from lower left dash bezel.
3. Lift bottom of dash
"A1" BRACKET USE HOLE #2
bezel out to allow
"A1" SOPORTE USA
ABERTURA NO. 2
top edge to unhook
from under air
vents, unplug
lighter, switches
and remove dash.
4. Extract two 7mm
hex head screws
holding radio in,
unplug connectors
LEFT SIDE
and remove radio.
LADO IZQUIERDA
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.

1992-95 Oldsmobile Achieva

Radio Removal:
1. Extract the two screws from the bottom of the dash bezel, below the radio and above the console pocket,
securing it to the dash.
2. Extract the two screws above the instrument cluster.
3. Remove the two screws above the AC vent located in the
center of the dash.
4. Pull the dash bezel out away from the dash and using a
panel removal tool/screwdriver, carefully disconnect the
fastening clips securing the dash vents (the one in the
center and the one on the driver's side) to the bezel.
5. Disconnect all the connectors and slide the dash bezel
away from the dash towards the passenger side.
6. Extract the two 10mm bolts securing the radio to the
dash, pull the radio from the cavity, unplug all the
connectors, and remove the radio.
SECURE THE KIT PANEL TO THE DASH USING THE SUPPLIED CARRIAGE BOLTS AND NUTS.
Asegure el panel estuche al tablero usando los pernos de porte y tuercos proveidos.
1985-91 Oldsmobile Cutlass Calais
Radio Removal:
1. Open armrest and extract (2) Phillips
head screws from bottom of pocket.
2. Remove pocket and extract (2) 10mm
bolts from underneath. Lift and slide
armrest towards rear of car.
3. Extract (2) 7mm/t-15 bolts from rear edge
of gear select lever trim panel. Remove
ashtray (on center console) and extract
(1) 7mm/t-15 bolt from underneath.
4. Put car in low gear. Lift and slide center
console towards rear of car
5. Gently unsnap and remove radio trim
bezel.
6. Extract (2) 7mm/T-15 Torx screws
securing radio to the dash, unplug wiring,
antenna, and remove radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
"B1" BRACKET USE HOLE #2
"B1" SOPORTE USA
ABERTURA NO. 2
RIGHT SIDE
FRONT OF KIT
LADO DERECHO
FRENTE DE ESTUCHE
CARRIAGE BOLT
PERNO DE PORTE
BOTTOM
FONDO
FLANGE NUT
TUERCO REBORDE
BREAK OFF TAB
ROMPE LA LENGUETA
BOTTOM
FONDO
"C1" BRACKET
USE HOLE #5
"C1" SOPORTE
USA ABERTURA NO. 5
"D1" BRACKET USE HOLE #1
"D1" SOPORTE USA ABERTURA NO. 1
24
Read pages 1993-02 Pontiac Firebird
3-7 for kit
assembly. Radio Removal:
1. Using a panel removal tool/screwdriver, carefully release the fastening clips from around the perimeter of
the radio trim bezel and remove the bezel.
2. Extract the four screws securing the radio to the dash, pull the radio from the cavity, unplug all the
connectors, and remove the radio.
"A1" BRACKET USE HOLE #1
"A1" SOPORTE
USA ABERTURA NO. 1
"C2" BRACKET
USE HOLE #1
"C2" SOPORTE USA ABERTURA NO. 1
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1985-92 Pontiac Firebird
Read pages
3-7 for kit
assembly.
Radio Removal:
1. Carefully pull on the edges of the radio trim panel to release the panel clips and remove the panel.
2. Remove the four screws which secure the radio to the console.
3. Disconnect the antenna, speaker leads and all the electrical connections, then remove the radio.
"A1" BRACKET USE HOLE #1
"A1" SOPORTE
USA ABERTURA NO. 1
"C2" BRACKET
USE HOLE #1
"C2" SOPORTE
USA ABERTURA NO. 1
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1996-98 Pontiac Grand Am
Read pages
3-7 for kit
assembly.
Radio Removal:
1. Extract two screws from the dash bezel above instrument/gauges.
2. Extract two screws from back of deep storage pocket below the radio.
3. Carefully pull out on the instrument/radio panel to release snap clips, unplug switches and remove bezel.
4. Extract three 7mm screws securing radio, unplug connectors, antenna lead, and remove radio.
"C2" BRACKET
USE HOLE #5
"C2" SOPORTE
USA ABERTURA NO. 5
TRIM BRACKET
CORTA EL SOPORTE
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
LEFT SIDE RIGHT SIDE
LADO IZQUIERDA LADO DERECHO
1
1
1
FRONT OF KIT
FRENTE DE ESTUCHE
"B2" SOPORTE USA ABERTURA NO. 1
RIGHT
LEFT
LADO IZQUIERDA LADO DERECHO
1
1
FRONT OF KIT
1
1
FRENTE DE
ESTUCHE
RIGHT SIDE
LEFT SIDE
LADO DERECHO
LADO IZQUIERDA
1
FRONT OF KIT
2
FRENTE DE
ESTUCHE
29
Read pages
3-7 for kit
assembly.
"B1" BRACKET USE HOLE #1
"B1" SOPORTE
USA ABERTURA NO. 1
1
"B2" BRACKET
USE HOLE #1
Read pages
3-7 for kit
assembly.
"B1" BRACKET USE HOLE #1
"B1" SOPORTE
USA ABERTURA NO. 1
TRIM BRACKET
CORTA EL
SOPORTE
"D2" BRACKET USE HOLE #1
"D2" SOPORTE USA ABERTURA NO. 1
Read pages
3-7 for kit
assembly.
"B1" BRACKET USE HOLE #1
"B1" SOPORTE USA
ABERTURA NO. 1