1994-96 Caprice Classic; 1995-99 Cavalier; Chevrolet ( Cont'd) 1994-96 Impala Ss - Scosche GM1503 Nstallation Instructions

1994-96 Chevrolet Caprice Classic
1994-96 Chevrolet Impala SS
Radio Removal:
1. Remove the fuse panel on the left side of the dash.
2. Extract one 9 / inch screw behind the fuse panel.
32
3. Extract the two 9 / inch screws from the under the dash panel on the driver's side (not the black wiring
32
access panel).
4. Extract the two 9 / inch screws from below the ash tray.
32
9
5. Extract the two / inch screws from the top of the instrument panel bezel.
32
6. Make sure the parking brake is on, then insert the key and turn to the "on" position.
7. Put the vehicle into first or low gear, and tilt the steering column adjustment all the way down and pull
outward on the instrument panel bezel. There are two spring clips on the bottom, release and remove the
spring clips.
8. Extract the four 9 / inch screws holding the ash tray, remove the ash tray , unplug the connector for the
32
light.
9. Open the glove box.
10. Starting from the left side of the dash, working below the steering column, pull gently outward to start
releasing the spring clips.
11. Work all the way across the dash piece, there are about eight spring clips total. The last one will pop out
near the glove box.
"A1" BRACKET
Remove the dash.
USE HOLE #2
LEFT SIDE
12. Extract the two 9 / "A1" SOPORTE
LADO
32
USA ABERTURA
IZQUIERDA
inch screws holding
NO. 2
the radio, slide the
radio out.
13. Unplug all the
connectors and the
antenna and remove
the radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1995-99 Chevrolet Cavalier
Radio Removal:
1. Extract one screw from the front center defroster vent on top of the dashboard.
2. Using a panel removal tool carefully snap out the vent and remove it.
3. Extract one 7mm hex head screw from under defrost vent.
4. Using a panel removal tool remove the left dash side panel surrounding the fuse block opening and
remove one 7mm screw from that location.
5. Using a panel removal tool release the panel at the right side of the dash and remove one 7mm screw
behind.
6. Open glove box, extract three screws holding the front edge of the dash panel.
7. Extract two brass 7mm screws from access hole in the roof of glove box securing metal bracket.
8. Carefully release fastening clips securing the top of the dash panel above the instrument cluster, lift the
panel up and away to remove.
CAUTION!: Passenger airbag cover is attached to the dash panel and will come off with the panel. USE
EXTREME CARE WHEN WORKING AROUND THE INNER AIRBAG SKIN!
9. Extract three 7mm screws from the radio trim bezel and use a panel removal tool to release the snap
clips
"C1" BRACKET
around the
LEFT SIDE
USE HOLE #2
LADO IZQUIERDA
radio and "C1" SOPORTE USA
ABERTURA
steering
NO. 2
column.
2
10. Unplug
bezel and
remove.
11. Extract two
screws holding
radio in, unplug and
remove radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
"B1" BRACKET
RIGHT SIDE
USE HOLE #2
LADO DERECHO
"B1" SOPORTE
USA ABERTURA
FRONT OF KIT
FRENTE DE ESTUCHE
"D1" BRACKET USE HOLE #2
RIGHT SIDE
"D1" SOPORTE USA
LADO DERECHO
NO. 2
2
FRONT OF KIT
FRENTE DE ESTUCHE
17
Read pages
3-7 for kit
assembly.
NO. 2
Read pages
3-7 for kit
assembly.
ABERTURA