1986-94 S-10 Blazer; 1986-93 S-10 Pickup; 1988-95 Van, Full Size; 1986-94 S-15 Jimmy - Scosche GM1503 Nstallation Instructions

1992-1995 Pontiac Grand Am
Radio Removal:
1. Extract the screw from the underside of the radio trim bezel.
2. Extract the five screws from the upper glove box securing the glove box assembly and remove the glove
box.
3. Open up the lower glove box and extract the three screws securing the radio trim bezel near the pin
switch.
4. Extract the three screws from below the steering column that
secure the top of the driver's side lower dash.
5. Extract the five screws securing the lower section of the driver's
side lower dash panel and remove the panel.
6. Extract the screw securing the radio trim bezel behind the
driver's side lower dash panel.
7. Using a panel removal tool/screwdriver, carefully pry the radio
trim bezel outward to release and remove it.
8. Remove the two nuts from below the radio cavity securing the
radio to the dash, pull the radio from the cavity, unplug the
leads and remove the radio.
SECURE THE KIT PANEL TO THE SUB-DASH USING THE SUPPLIED CARRIAGE NUTS AND BOLTS.
Asegura el panel estuche al tablero-sub usando los tuercos y pernos de porte.
1985-91 Pontiac Grand Am
Radio Removal:
1. Unsnap the front edge of the gearshift trim piece from the center console.
2. Gently pull on the radio trim panel to release the snaps and remove the trim.
3. Remove the two screws which secure the radio
and slide the radio out of the cavity.
4. Disconnect the antenna, speaker leads and all the
electrical connections, then remove the radio.
USE THE FACTORY BRACKET ON TOP OR USE THE "F" BRACKET ON THE TOP RIGHT AND THE "G" BRACKET ON THE TOP LEFT.
Usa el soporte fabrica de arriba o usa el soporte "F" arriba y a la derecha y el soporte 'G" arriba y a la izquierda.
1997-99 Pontiac Grand Prix
Radio Removal:
1. Extract two panel fasteners from driver's (left) side underdash cover.
2. Extract two 7mm hex screws from bottom edge of driver's (left) side lower dash panel and carefully pull
out on the upper panel to release two panel clips. Unplug and remove the dash piece.
3. Carefully pull out on the complete dash/radio/instrument bezel, unsnap, and unplug before removing.
4. Extract two 7mm screws holding the factory radio, unplug connectors and antenna to remove radio.
"A1" BRACKET USE HOLE #2
"A1" SOPORTE USA ABERTURA NO. 2
LEFT SIDE
LADO IZQUIERDA
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
FLANGE NUT
TUERCO REBORDE
TOP
TOPE
CARRIAGE BOLT
PERNO DE PORTE
"G" BRACKET
SOPORTE "G"
"F" BRACKET
SOPORTE "F"
TOP
TOPE
"B1" BRACKET USE HOLE #2
"B1" SOPORTE USA ABERTURA NO. 2
RIGHT SIDE
FRONT OF KIT
LADO DERECHO
FRENTE DE ESTUCHE
30
1986-94 Chevrolet S-10 Blazer
Read pages
3-7 for kit
1986-93 Chevrolet S-10 Pickup
assembly.
1986-94 GMC S-15 Jimmy
1986-93 GMC S-15 Pickup
1991-94 Oldsmobile Bravada
Radio Removal:
1. Open the glove box door and remove the
two screws from the radio trim panel.
2. Remove the ashtray and remove one
screw from the upper inside corner of the
recess and one from the lower
inside corner. Remove the trim
panel.
3. Remove the two screws which
secure the radio to the dash,
disconnect the wiring, and
remove the radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1982-85 Chevrolet S-10 Blazer, Pickup
Read pages
3-7 for kit
1982-85 GMC S-15 Jimmy, Pickup
assembly.
Radio Removal:
1. Remove the four screws from the radio trim panel.
2. Remove the single screw from the lower right corner of the instrument cluster trim panel.
3. Remove the radio trim panel.
4. Remove the four screws retaining the radio/dummy panel. Pull the radio out of the cavity, disconnect the
antenna,
speaker leads,
and all the
electrical
connections,
then remove the
radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1988-95 Chevrolet Van, Full Size
Read pages
3-7 for kit
1988-95 GMC Van, Full Size
assembly.
Radio Removal:
1. Remove the two screws from the top inside of the ashtray area.
2. Remove the two screws from the bottom front of the engine hump cover, pull the cover off and remove
the electrical harnesses. Then remove the engine hump cover/shell.
3. Remove the single screw from the right side of the chassis securing the rear support bracket to the
firewall. (A 10mm socket wrench will be needed).
4. Carefully snap off the radio
trim piece.
5. Remove the two screws
(10mm ) securing the radio
to the dash, one at each
side of the chassis.
6. Pull the radio out of the
cavity, remove the antenna
lead, disconnect the wire
harnesses and remove the
radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
LEFT SIDE
LADO IZQUIERDA
FRONT OF KIT
FRENTE DE
"C2" BRACKET
USE HOLE #3
ESTUCHE
"C2" SOPORTE USA ABERTURA NO. 3
LEFT SIDE RIGHT SIDE
"C1" BRACKET USE HOLE #3
LADO IZQUIERDA LADO DERECHO
"C1" SOPORTE
USA
6
ABERTURA
NO. 3
6
FRONT OF KIT
"C2" BRACKET
FRENTE DE
USE HOLE #3
ESTUCHE
"C2" SOPORTE USA ABERTURA NO. 3
"C1" BRACKET USE HOLE #3
"C1" SOPORTE USA ABERTURA NO. 3
3
FRONT OF KIT
LEFT SIDE
FRENTE DE
LADO IZQUIERDA
ESTUCHE
23
Read pages
3-7 for kit
assembly.
RIGHT SIDE
LADO DERECHO
"B1" BRACKET
USE HOLE #4
"B1" SOPORTE USA
ABERTURA NO. 4
Read pages
3-7 for kit
assembly.
"B1" BRACKET USE HOLE #4
"B1" SOPORTE USA
ABERTURA NO. 4
7
7
"B2" BRACKET
USE HOLE #4
"B2" SOPORTE USA ABERTURA NO. 4
Read pages
3-7 for kit
assembly.
"B1" BRACKET USE HOLE #3
"B1" SOPORTE USA ABERTURA NO. 3
3
RIGHT SIDE
LADO DERECHO