Table of Contents
Advertisement
1982-91 Pontiac 6000
Radio Removal:
1. Loosen the screw securing the radio trim panel to the left side of the glove box.
2. Carefully pull the panel outward to relieve the clips retaining the left side of the panel. Remove the trim
panel.
3. Remove the four screws retaining the radio, and pull the radio out of the cavity.
4. Disconnect the antenna, speaker leads and all the electrical connections, then remove the radio.
LEFT
"A1" BRACKET USE HOLE #2
LADO IZQUIERDA
"A1" SOPORTE USA ABERTURA NO. 2
2
FRONT OF KIT
1
"C2" BRACKET USE HOLE #1
"C2" SOPORTE USA
ABERTURA NO. 1
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1991-94 Saturn SC, SL, SL1, SL2
Radio Removal:
1. Using a panel removal tool/screwdriver, carefully pry outward on the dash bezel to release the clips and
remove the bezel.
2. Extract the two screws
securing the radio to the
dash. Pull the unit out of the
dash, unplug the
connectors and remove the
radio.
FRONT OF KIT
FRENTE DE ESTUCHE
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
RIGHT
"B1" BRACKET USE HOLE #2
LADO DERECHO
"B1" SOPORTE USA ABERTURA NO. 2
2
TRIM
BRACKET
CORTA EL
SOPORTE
FRENTE DE
1
ESTUCHE
"D2" BRACKET USE HOLE #1
"D2" SOPORTE USA ABERTURA NO. 1
"C1" BRACKET
USE HOLE #2
"C1" SOPORTE
USA ABERTURA NO. 2
"B1" BRACKET
USE HOLE #2
"B1" SOPORTE
USA ABERTURA NO. 2
TOP
TOPE
32
1990-93 Chevrolet Lumina APV
Read pages
3-7 for kit
1990-93 Oldsmobile Silhouette
assembly.
1990-93 Pontiac Trans Sport
Radio Removal:
1.
Open the glove box to access the two screws on the right side that secure
the radio trim.
2.
From the driver's side remove the three screws from the belly trim piece: one at the hood release, one
above the diagnostic connector and one at the lower backside of the console trim.
3.
Release the spring clips from the top of the lower steering column trim piece and remove the trim.
4.
Extract the two screws securing
the left side of the radio trim and
remove the trim.
5.
Using a socket wrench, reach
under the radio and remove the nut
securing the bottom of the radio.
6.
Extract two screws from the top
radio bracket, pull the unit out,
disconnect connectors and remove
radio.
USE THE SUPPLIED CARRIAGE BOLTS & NUTS TO MOUNT THE KIT PANEL TO THE SUB-DASH.
Usa los pernos de portey tuercos proveidos para montar la tablera estuche al tablero-sub.
Read pages
3-7 for kit
1997-00 Chevrolet Malibu
assembly.
Radio Removal:
1.
Carefully pop out plastic collar around ignition key and remove.
2.
Carefully
"A1" BRACKET
pop out
USE HOLE #2
radio trim,
"A1" SOPORTE
USA ABERTURA NO. 2
unplug
lighter and
remove.
3.
Extract two
7mm screws
holding radio in,
unplug all
connectors and
remove radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1986-88 Chevrolet Monte Carlo
1986-87 Chevrolet El Camino
Radio Removal:
1.
Remove the two screws from the top of the radio trim panel and the two screws from the bottom edge of
the trim panel.
2.
Remove the four screws which secure the radio, slide the radio out of the dash cavity and disconnect the
wiring
connectors.
3.
Remove the
radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
"C1" BRACKET USE HOLE #2
"C1" SOPORTE USA
ABERTURA NO. 2
CARRIAGE BOLT
PERNO DE
PORTE
FLANGE
NUT
TUERCO REBORDE
BOTTOM
FONDO
LEFT SIDE
LADO
IZQUIERDA
FRONT OF KIT
FRENTE DE ESTUCHE
LEFT
RIGHT
"A1" BRACKET USE HOLE #4
LADO IZQUIERDA
LADO DERECHO
"A1" SOPORTE USA
ABERTURA
4
NO. 4
FRONT OF KIT
4
FRENTE DE
"C2" BRACKET
ESTUCHE
USE HOLE #4
"C2" SOPORTE USA ABERTURA NO. 4
21
Read pages
3-7 for kit
assembly.
WASHER
ARANDELA
CUT OFF TAB
(TWO BRACKETS)
ROMPE LENQUETE
(DOS SOPORTES)
TOP
TOPE
"D1" BRACKET
USE HOLE #2
" D1" SOPORTE USA
ABERTURA NO. 2
Read pages
3-7 for kit
assembly.
"B1" BRACKET
RIGHT SIDE
USE HOLE #2
LADO DERECHO
"B1" SOPORTE
USA ABERTURA
NO. 2
Read pages
3-7 for kit
assembly.
"B1" BRACKET USE HOLE #1
"B1" SOPORTE
USA ABERTURA
NO. 1
2
TRIM
BRACKET
CORTA EL
SOPORTE
2
"D2" BRACKET USE HOLE #1
"D2" SOPORTE USA ABERTURA NO. 1
Advertisement
Table of Contents
