Page 1
Case IH Patriot 4440, Non- Steer Ready MY 17 and Newer SmarTrax Installation Manual P/N 016-5032-043 Rev. A 12/16 E28539 Copyright 2016...
Page 2
GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the accuracy, integrity, continuity, or availability of these services and cannot guarantee the ability to use Raven systems, or products used as components of systems, which rely upon the reception of these signals or availability of these services.
• Ensure SmarTrax is disabled prior to starting any maintenance work on SmarTrax or the machine. WARNING • When starting the machine for the first time after installing SmarTrax, be sure that all persons stand clear in case a hose has not been properly tightened.
• Clamp harnesses securely to force controlled movement to occur in the desired harness section • Avoid sharp twisting or flexing of harnesses in short distances • Connectors and splices should not be located in harness sections that move Case IH Patriot 4440, Non-Steer Ready MY 17 and Newer SmarTrax Installation Manual...
Important Safety Information: Protect harnesses from: • Foreign objects such as rocks that may fall or be thrown by the unit • Buildup of dirt, mud, snow, ice, submersion in water and oil • Tree limbs, brush and debris • Damage where service personnel or operators might step or use as a grab bar •...
Page 8
• Tree limbs, brush and debris • Damage where service personnel or operators might step or use as a grab bar • Damage when passing through metal structures • High pressure wash Case IH Patriot 4440, Non-Steer Ready MY 17 and Newer SmarTrax Installation Manual...
PREPARING FOR INSTALLATION Before installing the SmarTrax system, park the machine where the ground is level, clean, and dry. Turn off the machine and leave it turned off for the duration of the installation process. Bleed pressure from the hydraulic system by loosening the hydraulic fittings slowly, where applicable.
Software and manual updates are available on the Raven Applied Technology website: http://www.ravenhelp.com At Raven Industries, we strive to make your experience with our products as rewarding as possible. One way to improve this experience is to provide us with feedback on this manual.
KIT CONTENTS This section contains a list of the components that are included in the SmarTrax kit. Before beginning the SmarTrax installation, compare the items in the kit with the components on this list. If you have questions about the kit, contact your Raven dealer.
Page 12
333-0012-104 Fitting - -6 ORFS (M) to -8 SAE O-Ring 333-0012-199 (M) Straight Adapter Fitting - -6 ORFS (M) to -10 SAE O-Ring 333-0012-233 (M) Straight Adapter Case IH Patriot 4440, Non-Steer Ready MY 17 and Newer SmarTrax Installation Manual...
Objects or materials that are able to bypass the machine’s hydraulic filtration system will reduce performance and possibly damage the SmarTrax hydraulic valve. P/N 016-5032-043 Rev. A...
INSTALL FITTINGS ON THE SMARTRAX VALVE Before mounting the SmarTrax valve (P/N 334-0003-088) on the machine, install the proper fittings in the valve. This prepares the valve for installation and simplifies the hose connection process later in the procedure.
2. Install the pressure transducers in Ports A1 and B1 of the flow switch. MOUNT THE SMARTRAX VALVE INSTALL THE SMARTRAX VALVE MOUNTING BRACKET FIGURE 3. Valve Mounting Location 1. Remove the bolts used to secure the machine’s radar bracket (beneath the cab).
1. MOUNT THE SMARTRAX VALVE 1. Mount the SmarTrax valve (P/N 334-0003-088) to the valve mounting bracket (P/N 107-0171-705) using four 5/ 16” hex bolts (P/N 311-0052-104) and four 5/16” lock washers (P/N 313-1000-019). 2. Mount the flow switch (P/N 334-0003-085) to the valve mounting bracket using two 1/4”-20 x 2” screws (P/N 311-0050-109), two 1/4”...
5. Install the 90° end of the supplied hydraulic hose (P/N 214-1000-657) on the 90° end of the installed tee fitting. 6. Connect the straight end of the installed hydraulic hose to Port P of the SmarTrax valve. INSTALL THE TANK HOSE 1.
11. Install the 90° end of the supplied hydraulic hose (P/N 214-1000-659) on the 90° end of the installed tee fitting. 12. Connect the straight end of the installed hydraulic hose to Port B of the SmarTrax valve (P/N 334-0003-088).
Tabs When choosing the location for the SmarTrax node, consider the following points: • Mount the SmarTrax node inside the machine’s cab on a flat, level surface for proper performance and cable connection. • One of the six numbered direction arrows on the node must be oriented in the direction of forward vehicle travel, one arrow pointing straight up, and two of the arrows parallel to the ground.
2. Remove any contents from under the instructional seat. FIGURE 3. Floor Mat Removed from Cab 3. Lift the floor mat from the floor in front of the seat. Case IH Patriot 4440, Non-Steer Ready MY 17 and Newer SmarTrax Installation Manual...
Page 25
4. Remove the plastic molding under the instructional seat by removing the nuts and bolts securing it. FIGURE 5. Node Mounted to Mounting Plate 5. Mount the SmarTrax node (P/N 063-0173-228) to the node mounting bracket (P/N 107-0172-084) using three 3/8”-16 zinc flanged lock nuts (P/N 312-1001-164).
Page 26
FIGURE 7. DGPS OUT Connector Routed Under Operator’s Seat 12. Route the DGPS OUT connector out the right corner of the operator’s seat base and under the right arm rest. Case IH Patriot 4440, Non-Steer Ready MY 17 and Newer SmarTrax Installation Manual...
Page 27
Cab Component Installation: FIGURE 8. Convenience Tray Removed 13. Remove the convenience tray from the right-rear corner of the cab. 14. Locate the POWER GND PORT on the machine’s harness in the convenience tray compartment. 15. Connect the machine’s POWER GND PORT connector to the mating 6-pin POWER connector on the node harness.
3. Align the hole in the node mounting bracket (P/N 107-0171-954) with the hole in the machine’s bracket. 4. Using the node mounting bracket as a template, drill a second hole in the machine’s bracket. Case IH Patriot 4440, Non-Steer Ready MY 17 and Newer SmarTrax Installation Manual...
Page 29
Cab Component Installation: FIGURE 12. Node Mounting Bracket Installed 5. Reinstall the machine’s spacer between the traction control pedal and the machine’s bracket. 6. Secure the node mounting bracket to the machine’s bracket using two 1/4”-20 x 1-1/4” hex bolts (P/N 311-0050- 106), two 1/4”...
Page 30
FIGURE 15. Node Support Bracket Secured to Cab Floor 11. Secure the node support bracket to the cab floor using one #10 x 3/4” self-tapping slotted hex head screw (P/ N 311-0001-321). Case IH Patriot 4440, Non-Steer Ready MY 17 and Newer SmarTrax Installation Manual...
Page 31
Cab Component Installation: FIGURE 16. Node Harness Installed on Node 1. Install the two large, rectangular connectors of the node harness (P/N 115-4001-191) into the correct ports of the node, tightening the bolts on the harness connectors to secure the connections. FIGURE 17.
1. Select a suitable location for the foot switch (P/N 063-0172-470) to be installed. NOTE: The foot switch should be installed in a location where the operator has easy access to it and is able to fully press the pedal. Case IH Patriot 4440, Non-Steer Ready MY 17 and Newer SmarTrax Installation Manual...
Cab Component Installation: 2. Using the holes in the foot switch as a template, drill holes in the floor of the cab. 3. Secure the foot switch to the floor by installing the supplied screws in each of the mounting holes. 4.
Page 34
NOTE: These connections can be plugged into either transducer. 4. Plug the VALVE connector from the valve cable into the open port at the end of the SmarTrax valve (P/N 334- 0003-088). Case IH Patriot 4440, Non-Steer Ready MY 17 and Newer SmarTrax Installation Manual...
5. Access the System Diagnostic screen by selecting the MACHINE TEST option on the Machine Type screen and turn the wheels using the Raven field computer. The machine may need to be rolling forward to allow the wheels to turn left or right.
HAPTER CALIBRATE THE SMARTRAX SYSTEM Refer to the SmarTrax Calibration & Operation Manual (P/N 016-0171-277) for instructions on calibrating the SmarTrax system, adjusting system settings, and system operation. Case IH Patriot 4440, Non-Steer Ready MY 17 and Newer SmarTrax Installation Manual...
Page 39
Mounting the SmarTrax Valve 14 Installing the Tank Hose Mounting the SmarTrax Valve Installing SmarTrax Valve Mounting Bracket 13 Installing the SmarTrax Valve Mounting Plate 13 Introduction Kit Contents Preparing for Installation Point of Reference 6 Recommendations 5 Updates Kit Contents...
Page 40
Index Case IH Patriot 4440, Non-Steer Ready MY 17 and Newer SmarTrax Installation Manual...
Page 41
Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval. The freight cost to Raven Industries will be the customer’s responsibility. The Return...
Page 42
How Can I Get Service? Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval.