Raven SmarTrax Installation Manual
Macdon m150, m155, m200, and m205 series windrower
Hide thumbs
Also See for SmarTrax:
- Calibration and operation manual (156 pages) ,
- Operation manual (73 pages) ,
- Installation manual (59 pages)
Related Manuals for Raven SmarTrax
Summary of Contents for Raven SmarTrax
- Page 1 MacDon M150, M155, M200, and M205 Series Windrower SmarTrax™ Installation Manual P/N 016-5030-009 Rev B 09/15 E20834 Copyright 2012, 2013, 2015...
- Page 2 GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the accuracy, integrity, continuity, or availability of these services and cannot guarantee the ability to use Raven systems, or products used as components of systems, which rely upon the reception of these signals or availability of these services.
-
Page 3: Table Of Contents
Point of Reference ....................... 4 Updates ............................. 4 Kit Contents ..........................5 Chapter 3 Cab Component Installation ..........7 Install the SmarTrax Node ......................7 Mount the SmarTrax Node ....................7 Node Mounting Locations ....................8 Install the Node Harness ......................9 Install the Valve Harness ...................... - Page 4 Table of Contents MacDon M150, M155, M200, and M205 Series Windrower SmarTrax™ Installation Manual...
-
Page 5: Important Safety Information
Ensure SmarTrax is disabled prior to starting any maintenance work on SmarTrax or the machine. WARNING • When starting the machine for the first time after installing SmarTrax, be sure that all persons stand clear in case a hose has not been properly tightened. •... -
Page 6: Hydraulic Safety
CAUTION Hydraulic Safety • Raven Industries recommends that appropriate protective equipment be worn at all times when working on the hydraulic system. • Never attempt to open or work on a hydraulic system with the equipment running. Care should always be taken when opening a system that has been previously pressurized. -
Page 7: Introduction
SmarTrax system. Contact your local MacDon dealer for ordering information. Before installing the SmarTrax system, park the machine where the ground is level, clean, and dry. Turn off the machine and leave it turned off for the duration of the installation process. -
Page 8: Recommendations
Recommendations Raven Industries recommends the following best practices when installing or operating the SmarTrax system for the first time, at the start of the season, or when moving the SmarTrax system to another machine: • Install the GPS antenna in the recommended location. Refer to the following table for the machine-specific antenna mounting location. -
Page 9: Kit Contents
This section contains a list of the components that are included in the SmarTrax kit. Before beginning the SmarTrax installation, compare the items in the kit with the components on this list. If you have questions about the kit, contact your Raven dealer. - Page 10 TABLE 1. Picture Item Description Part Number Qty. Cable - Node Harness 115-4001-166 Cable - Valve Harness 115-4001-167 Tape - 3.5” Double-Sided 332-0000-019 Nut - 3/8”-16 Zinc Flanged Lock 312-1001-164 MacDon M150, M155, M200, and M205 Series Windrower SmarTrax™ Installation Manual...
-
Page 11: Cab Component Installation
(P/N 063-0173-484) face the right window of the cab when installed. Mount the SmarTrax node to the node mounting bracket using three 3/8”-16 zinc flanged lock nuts (P/N 312-1001-164). -
Page 12: Node Mounting Locations
Mounting Tabs When choosing the location for the SmarTrax node, consider the following points: • Mount the SmarTrax node inside the machine’s cab on a flat, level surface for proper performance and cable connection. • One of the six numbered direction arrows on the node must be oriented in the direction of forward vehicle travel, one arrow pointing straight up, and two of the arrows parallel to the ground. -
Page 13: Install The Node Harness
Cab Component Installation Install the Node Harness Node Harness Installed on the Node FIGURE 3. Install the two large, rectangular connectors of the node harness (P/N 115-4001-166) into the correct ports of the node, tightening the bolts on the harness connectors to secure the connections. Note: The connections should be pointing toward the right window. - Page 14 Reinstall the engage switch cable connector and pins, ensuring the pins are reinstalled into the correct cavity. Node Harness Connected to Engage Switch Harness FIGURE 7. Locate the ENABLE connector on the node harness and connect it to the engage switch harness. MacDon M150, M155, M200, and M205 Series Windrower SmarTrax™ Installation Manual...
-
Page 15: Install The Valve Harness
Cab Component Installation Install the Valve Harness Valve Harness Connected to the Node Harness FIGURE 8. Connect the green 12-pin connector of the valve harness (P/N 115-4001-167) into the mating 12-pin connector of the node harness (P/N 115-4001-166). Valve Harness Routed Outside the Cab FIGURE 9. - Page 16 Connect the PSI connector to the transducer installed in the MacDon steering valve. Connect the DOUBLE BLOCKER connector to the connector on the solenoid of the MacDon valve. WAS Connection FIGURE 12. MacDon M150, M155, M200, and M205 Series Windrower SmarTrax™ Installation Manual...
-
Page 17: Install The Chassis Cable
The chassis cable is sold separately. Contact your local Raven dealer for ordering information. Locate the SmarTrax chassis cable (P/N 115-4001-085). Connect the TO SMARTRAX NODE connector from the chassis cable to the round 16-pin connector on the node harness (P/N 115-4001-166). -
Page 18: System Diagram
Chapter 3 System Diagram MacDon M150, M155, M200, and M205 Series Windrower SmarTrax™ Installation Manual... - Page 19 Index Cab Component Installation Calibrating the SmarTrax System 13 Installing the Chassis Cable 13 Installing the Node Harness 9 Installing the SmarTrax Node 7 Mounting the SmarTrax Node 7 Node Mounting Locations 8 Installing the Valve Harness 11 System Diagram 14...
- Page 20 Index MacDon M150, M155, M200, and M205 Series Windrower SmarTrax™ Installation Manual...
- Page 21 Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval. The freight cost to Raven Industries will be the customer’s responsibility. The Return...
- Page 22 How Can I Get Service? Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval.
Need help?
Do you have a question about the SmarTrax and is the answer not in the manual?
Questions and answers