Raven SmarTrax Installation Manual
Case ih flx 4300 (2000 & newer)
Hide thumbs
Also See for SmarTrax:
- Calibration and operation manual (156 pages) ,
- Operation manual (73 pages) ,
- Installation manual (59 pages)
Related Manuals for Raven SmarTrax
Summary of Contents for Raven SmarTrax
- Page 1 Case IH FLX 4300 (2000 & Newer) SmarTrax™ Installation Manual P/N 016-0190-018 Rev D 09/15 Copyright 2009, 2015...
- Page 2 GPS satellites, the OmniSTAR correction service or the WAAS correction service. Raven Industries accepts no responsibility for the use of the signal for other than the stated purpose. Raven Industries shall not be responsible or liable for incidental or consequential damages or a loss of anticipated benefits or profits, work stoppage or loss or impairment of data arising out of the use, or inability to use, the SmarTrax or any of its components.
- Page 3 Manual # 016-0190-018 H A P T E R NTRODUCTION Congratulations on your purchase of the Raven SmarTrax system! This system is designed to provide cutting-edge, hands-free steering of your machine via GPS coordinates.
-
Page 4: Basic Kit
CaseIH FLX4300, 2000 & Newer SmarTrax Installation Manual Below you will see the kit contents that you should have received with this SmarTrax kit. Basic Kit Contents CaseIH FLX4300, 2000 & Newer SmarTrax Kit Contents t n a y t i... - Page 5 Caution must be exercised. Any work carried out on the hydraulic system must be performed in accordance with the machine manufacturerer’s approved maintenance instructions. Raven Industries recommends that appropri- ate protective equipment be worn when working on the hydraulic system. Ob- jects or materials that are able to bypass the machine’s hydraulic filtration system...
- Page 6 CaseIH FLX4300, 2000 & Newer SmarTrax Installation Manual We welcome your feedback about this manual. If you have any comments or Contacting suggestions for improvement, please let us know by contacting our Customer Raven Support Center by any of the following methods:...
- Page 7 Manual # 016-0190-018 H A P T E R NSTALLING THE NIVERSAL OUNTING RACKET The mounting location for the supplied mounting bracket is on the left hand side of the machine, located between the left front fender and the hydraulic oil reservoir, underneath the catwalk. Mounting location for steering control valve and bracket...
- Page 8 CaseIH FLX4300, 2000 & Newer SmarTrax Installation Manual Mount the steering manifold to the bracket using the supplied hardware. Mounting location of the hydraulic bracket Hole locations for hydraulic bracket...
- Page 9 Manual # 016-0190-018 H A P T E R YDRAULICS...
- Page 10 Attach 90° end of supplied hoses (P/N 214-1000-038) to the P, T, L, & R ports on the steering orbital then route hoses to the Smartrax valve. Connect Left Hose to A port, Right hose to B port, Pressure hose to P port, Tank hose to T port using the supplied 90°...
- Page 11 Manual # 016-0190-018 Connecting Begin by removing the load sense hose from the steering orbital. and Routing Once the hose is removed, connect the end of the hose that was just the LS-PV removed from the steering orbital to the supplied LS-PV hose (P/N 214-1000-041).
- Page 12 Once the hose is connected, route the hose back to the steering control the LS-Steer valve. Hose Connect the LS-Steer hose to the LS Steer port on the SmarTrax valve. Attach the pressure switch directly to the PS port on the SmarTrax valve.
- Page 13 Manual # 016-0190-018...
- Page 14 CaseIH FLX4300, 2000 & Newer SmarTrax Installation Manual Notes:...
- Page 15 Manual # 016-0190-018 H A P T E R & W TEERING OSITION ENSOR IRING ARNESS NSTALLATION Installing the Top figure shows the approximate mounting position of the steering position sen- sor. Attach one end of the steering position sensor to the steering tie-rod using Steering the provided band clamps, screws, and brackets.
- Page 16 CaseIH FLX4300, 2000 & Newer SmarTrax Installation Manual Cable Connect ends of the cable to the valve, pressure switch, and SPS. Connection Secure the cable away from moving parts and heat sources. and Routing...
-
Page 17: Start-Up Procedures
Manual # 016-0190-018 H A P T E R TART- ROCEDURES After installing the SmarTrax on your machine, always follow these start-up procedures. Make sure the Steering Position Sensor does not over-extend or over- compress when turning the wheels. Turn the wheels fully from side to side numerous times to remove air from the hydraulic system. - Page 18 CaseIH FLX4300, 2000 & Newer SmarTrax Installation Manual Notes:...
- Page 19 How Can I Get Service? Bring the defective part and proof of purchase to your Raven Dealer. If your Dealer agrees with the warranty claim, the Dealer will send the part and proof of purchase to their distributor or to Raven Industries for final approval.