FujiFilm SP-3000 Service Manual page 157

3.2 Messages and Actions
No. Message
E-4592 An error occurred during accessing of
the CTB circuit board external
memory.
Restart the system. If problems
persist, consult your technical
representative.
E-4595 Detecting of the shutter home
position failed.
Restart the system. If problems
persist, consult your technical
representative.
E-4596 Detecting of the shutter home
position failed.
Restart the system. If problems
persist, consult your technical
representative.
E-4597 The shutter control is abnormal.
Restart the system. If problems
persist, consult your technical
representative.
E-4598 The shutter control is abnormal.
Restart the system. If problems
persist, consult your technical
representative.
E-4599 The shutter control is abnormal.
Restart the system. If problems
persist, consult your technical
representative.
E-4600 The shutter control is abnormal.
Restart the system. If problems
persist, consult your technical
representative.
E-4601 The control for the CLE circuit board
is abnormal.
Restart the system. If problems
persist, consult your technical
representative.
E-4602 The control for the CLE circuit board
is abnormal.
Restart the system. If problems
persist, consult your technical
representative.
NOTE 1: The refreshing backup can be restored
Distributed by minilablaser.com
Factor
SKCTB-EEPROM writing abnormal
(Causes of the error message)
1. Faulty system software
2. Faulty CTB23 circuit board (CPU
or EEPROM)
SKCTB-shutter home position
operation abnormal 3
(Causes of the error message)
1. Faulty shutter home position
sensor (D203) harness
2. Faulty shutter drive motor (M203)
harness
SKCTB-shutter home position
operation abnormal 3
(Causes of the error message)
1. Faulty shutter home position
sensor (D203) harness
2. Faulty shutter drive motor (M203)
harness
SKCTB-shutter opening abnormal
(Causes of the error message)
1. Faulty shutter home position
sensor (D203) harness
2. Faulty shutter drive motor (M203)
harness
SKCTB-shatter opening timeout error
(Causes of the error message)
1. Faulty shutter home position
sensor (D203) harness
2. Faulty shutter drive motor (M203)
harness
SKCTB-shutter closing abnormal
(Causes of the error message)
1. Faulty shutter home position
sensor (D203) harness
2. Faulty shutter drive motor (M203)
harness
SKCTB-shutter closing timeout error
(Causes of the error message)
1. Faulty shutter home position
sensor (D203) harness
2. Faulty shutter drive motor (M203)
harness
SKCLE-message delivery module
initialization error 1
(Causes of the error message)
1. Faulty system software
2. Faulty CLE23 circuit board (CPU)
SKCLE-message delivery module
initialization error 2
(Causes of the error message)
1. Faulty system software
2. Faulty CLE23 circuit board (CPU)
(See Section 3.4).
3-96
Actions
1. Restart the system software. If the
error occurs again, reinstall the
system software. (NOTE 1)
2. Replace the circuit board.
1. Reconnect or replace the harness.
2. Reconnect or replace the harness.
1. Reconnect or replace the harness.
2. Reconnect or replace the harness.
1. Reconnect or replace the harness.
2. Reconnect or replace the harness.
1. Reconnect or replace the harness.
2. Reconnect or replace the harness.
1. Reconnect or replace the harness.
2. Reconnect or replace the harness.
1. Reconnect or replace the harness.
2. Reconnect or replace the harness.
1. Restart the system software. If the
error occurs again, reinstall the
system software. (NOTE 1)
2. Replace the circuit board.
1. Restart the system software. If the
error occurs again, reinstall the
system software. (NOTE 1)
2. Replace the circuit board.