YASKAWA A1000 Series Quick Start Manual page 152

4.6 Basic Drive Setup Adjustments
No.
E2-01
<1> Display is in the following units:
2A0004 to 2A0040, 4A0002 to 4A0023, and 5A0007 to 5A0017: 0.01 A units.
2A0056 to 2A0415, 4A0031 to 4A0675, and 5A0022 to 5A0242: 0.1 A units.
4A0930 and 4A1200: 1 A units.
Note: An oPE02 error will occur if E2-01 ≤ E2-03. Set E2-03 correctly to prevent this error.
n H1-01 to H1-08: Functions for Terminals S1 to S8
These parameters assign functions to the multi-function digital inputs. The various functions and settings are listed in
4.26.
No.
H1-01 Multi-Function Digital Input Terminal S1 Function Selection
H1-02 Multi-Function Digital Input Terminal S2 Function Selection
H1-03 Multi-Function Digital Input Terminal S3 Function Selection
H1-04 Multi-Function Digital Input Terminal S4 Function Selection
H1-05 Multi-Function Digital Input Terminal S5 Function Selection
H1-06 Multi-Function Digital Input Terminal S6 Function Selection
H1-07 Multi-Function Digital Input Terminal S7 Function Selection
H1-08 Multi-Function Digital Input Terminal S8 Function Selection
<1> Number appearing in parenthesis is the default value after performing a 3-Wire initialization (A1-03 = 3330).
Setting
0 3-Wire Sequence
1 LOCAL/REMOTE Selection
2 External Reference 1/2 Selection
3 Multi-Step Speed Reference 1
4 Multi-Step Speed Reference 2
5 Multi-Step Speed Reference 3
6 Jog reference Selection
7 Accel/Decel Time Selection 1
8 Baseblock Command (N.O.)
9 Baseblock Command (N.C.)
A Accel/Decel Ramp Hold
B Drive Overheat Alarm (oH2)
C Analog Terminal Input Selection
D PG Encoder Disable
E ASR integral reset
F Through Mode
10 Up Command
11 Down Command
12 Forward Jog
13 Reverse Jog
14 Fault Reset
15 Fast Stop (N.O.)
16 Motor 2 Selection
17 Fast Stop (N.C.)
18 Timer Function Input
19 PID Disable
152
Parameter Name
Motor Rated Current
Parameter Name
Table 4.26 Multi-Function Digital Input Terminal Settings
Function
Setting
Range
1 to 9F
40 (F)
1 to 9F
41 (F)
0 to 9F 24: External Fault
0 to 9F 14: Fault Reset
<1>
0 to 9F
3 (0)
<1>
0 to 9F
4 (3)
<1>
0 to 9F
6 (4)
0 to 9F 8: External Baseblock Command
Page Setting
153 1A Accel/Decel Time Selection 2
– 1B Program Lockout
– 1E Reference Sample Hold
20 to 2F External Fault
– 30 PID Integral Reset
31 PID Integral Hold
– 32 Multi-Step Speed Reference 4
– 34 PID Soft Starter Cancel
35 PID Input Level Selection
–
40 Forward Run Command (2-Wire sequence)
– 41 Reverse Run Command (2-Wire sequence)
– 42 Run Command (2-Wire sequence 2)
– 43 FWD/REV Command (2-Wire sequence 2)
– 44 Offset Frequency 1
– 45 Offset Frequency 2
– 46 Offset Frequency 3
47 Node Setup
–
60 DC Injection Braking Command
61 External Speed Search Command 1
–
62 External Speed Search Command 2
– 63 Field Weakening
– 65 KEB Ride-Thru 1 (N.C.)
– 66 KEB Ride-Thru 1 (N.O.)
– 67 Communications Test Mode
– 68 High Slip Braking (HSB)
– 6A Drive Enabled
YASKAWA ELECTRIC TOEP C710616 41G YASKAWA AC Drive - A1000 Quick Start Guide
Setting Range
10% to 200% of the drive
<1>
rated current
Default
<1>
: Forward Run Command (2-Wire sequence)
<1>
: Reverse Run Command (2-Wire sequence)
: Multi-Step Speed Reference 1
: Multi-Step Speed Reference 2
: Jog Reference Selection
Function
Default
Determined by
C6-01 and o2-04
Table
Page
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–