ADT FOCUS 200 PLUS Installation And Setup Manual page 199

477967 Battery, 12-Volt, 7.0AH Sealed Lead-Acid
A 12V, 7.0AH rechargeable battery with male tab terminals. Connects to control or power supply via a
separately ordered 248222 Battery Wire Lead. Two to four batteries may be connected in parallel to
make up a 12V, 14, 21, or 28AH battery. Battery weighs 6.17 pounds (28kg). One 248222 Battery Wire
Lead is required to connect each battery. Refer to the installation section of control unit bulletin for
instruction in calculating battery standby requirements.
248222 Battery Wire Leads
Consists of a set of two wire leads, one red and one black. Used for connection to a FOCUS 200 PLUS
control board or Remote Power Supply. Two sets of the battery wire leads are needed for installing two
batteries in parallel to provide a 12V, 14AH battery configuration. Each wire lead is 13-1/2" long; wire
size is 18 AWG.
471715 Printer Interface Unit
Used to interface a FOCUS Type printer into the system. Consists of a printed wiring board that is
housed in a separately ordered 472352 Housing Unit (PID box). Board has screw terminals for making
connections to the RS-485 bus and for connecting 12VAC power, and a header for making connections
to a 471958 (7187-058) Printer Kit or a 472369 Secure Printer Kit. A jumper plug serves to connect a
user bus-terminating resistor where required. A 443241 Transformer must be ordered separately. A
separately ordered 248116 Tamper Kit is available.
472381 Power Unit and Power Housing
A cabinet for housing the components needed to provide additional power for the FOCUS 200 PLUS
System. Cabinet comes with a key lock and two keys. Power can be introduced directly to the RS-485
Bus (via the red and black wires) or it can be introduced via a SIM or PID gateway. Cabinet comes with
hardware for mounting internal components, assembly instructions, and basic battery leads. Facilities
are provided for housing the following items, all of which must be ordered separately, as needed:
1. 472372 Power Supply Module (for providing 12VDC power). Module comes with terminals for
connecting an input transformer, making battery connections, connecting the 12V output power,
and for connecting a SIM or PID to supervise the application of AC power. Power supply output
rating is 1.5A if using a 50VA input transformer, and 2.5A if using an 82VA input transformer.
One required.
2. 443216 or N8167 Transformer (50VA), 472404 Transformer (72VA), or 443219 Transformer (50VA,
hardwire), as required. One required.
3. 477967 Battery (up to 4), as required. One set of 248222 Battery Leads with slip-on terminals are
provided. Order another set of leads for each additional battery.
4. 472366 SIM or 471941 Micro PID (for supervision of AC power). One required. If using a Micro
PID, also order the 472352 PID Housing for mounting the Micro PID.
If housing is also to accommodate a gateway, order the following SIM or PID gateway components, as
required, in place of the ones mentioned in Item (4) above:
For a SIM Gateway
(1) 472368 SIM Gateway
(1) 472366 SIM (for supervision)
(1) 472352 PID Housing (for SIM gateway)
866682 Power Unit
This power unit comes with a built-in supervisory circuit.
443241 Transformer
A 120/12V, 20VA, Class II transformer for supplying primary power to the 471715 Printer Interface
Unit.
For a PID Gateway
(1) 248239 PID Gateway
(1) 472352 PID Housing (for PD gateway)
(1) 471941 Micro PD (for supervision)
(1) 471943 Micro PD Housing (for Micro PD)
Section 22 – Equipment
AI=SI=0mA
22-3