BRP I-Command Evinrude Etec Series User Manual
  1. Manuals
  2. Brands
  3. BRP Manuals
  4. Measuring Instruments
  5. I-Command Evinrude Etec Series
  6. User manual

BRP I-Command Evinrude Etec Series User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

User's Guide

Advertisement

Table of Contents
loading

Related Manuals for BRP I-Command Evinrude Etec Series

Summary of Contents for BRP I-Command Evinrude Etec Series

  • Page 1 User’s Guide...
  • Page 2 ht t p : / / w ww. b oa t - f u e l - e c o nomy . c o m/ e v i n r u de - i c o mma n d- f o r - s a l e...
  • Page 3 BRP US Inc. / Outboard Engines Division After Sales Support P.O. Box 597 Sturtevant, WI 53177 © 2008 BRP US Inc. All rights reserved. TM, ® and the BRP logo are registered trademarks of Bombardier Recreational Products Inc. or its affiliates.
  • Page 4 For questions or problems regarding the I-Command LMF-400 Version 1.5.0 Digital gauge, contact your dealer. Build AZ622 Dealers with questions should contact BRP Parts and Accessories Technical Help. M E N U WARNING For your safety and the safety of others, follow 1.

  • Page 5: Table Of Contents

    TABLE OF CONTENTS Installation Advanced Setup and Operation Description .......5 Configure Fluid Level Sensor .

  • Page 6: Installation

    Installation...

  • Page 7: Description

    Description The I-Command™ Digital Integrated Performance System uses “plug and play” networking technology based on NMEA 2000 data communications standards (National Marine Electronics Association). These standards † provide communications through a serial data network utilizing a Controller Area Network (CAN) integrated circuit (IC).

  • Page 8: Instruments

    Instruments Spacing of Instruments The minimum distances between instruments on a panel should be as follows: •3 13/16 (112 mm) center to center for 3 1/2 in. instruments •3 1/4 in. (95.5 mm) center to center for 3 1/2 in. instruments to 2 in. instruments •2 5/8 in.
  • Page 9 Gauge Dimensions 2.87 in. 2.20 in. (72.9 mm) 0.71 in. (56 mm) (18 mm) 1.95 in. (49.5 mm) 3.81 in. (96.9 mm) 3.34 in. (85 mm)
  • Page 10 Warning Horn Connect the yellow wire from the instrument to the black wire of the warning horn. Connect the blue wire from the instrument to the red wire of the warning horn. Each instrument should be installed with a warning horn. Mount each warning horn in a protected area and so horn is audible for operator.

  • Page 11: Network Devices

    Network Devices Also see the “Network Specification Diagram” on page 10. Buss Length The distance between any two points on the network must not exceed 100 meters (328 ft.). Measure the distance from the Tee-connector to the last device at each end of the network. Device cable lengths at the ends of the network must be included in the total network buss length calculation.
  • Page 12 Network Specification Diagram Open Network Connector REMOVE 100M (328 ft.) Maximum Network Terminator Buss Length Terminator Power supply & Ground connection Device cables 6M (19 ft.) 6M (19 ft.) maximum maximum NMEA x 100 ® 2000 4257 Device NMEA MEN U ®...
  • Page 13 Device Net-style Connectors I-Command and NMEA 2000 networks use DeviceNet Micro-C type connec- tors. These connectors use 12 mm threaded locking rings and are water- proof when assembled properly. All DeviceNet Micro-C connectors are compatible with the I-Command red network connectors. Connectors with slighty different appearances supplied with I-Command or NMEA 2000 devices should NOT affect network operation.
  • Page 14 Terminating Resistors Terminating resistors are required for accurate network transmissions. Net- works must be assembled with one terminator installed at each end of the I-Command network. See the “Network Specification Diagram” on page 10. Tee-Connectors and Buss Cables Tee-connectors provide each device access to the network. Single Tee-con- nectors have two buss connectors and one device connector.
  • Page 15 Mounting Connectors When mounting connectors, pay attention to connector alignment. Some connectors may have different mounting boss dimensions. If necessary, use an appropriate spacer behind the connector. Mount connectors to a flat mounting surface with screws. Tighten screws by hand. Using a power driver can over tighten screws and damage connectors.

  • Page 16: Network Setup

    Network Setup IMPORTANT: Set “ENGINE OPTIONS” on Evinrude E-TEC outboards before power is applied to the I-Command Network. Engine Options Use Evinrude Diagnostics software to set “ENGINE OPTIONS”. Settings include: Evinrude Diagnostics software, set engine •Set multi engine identity (engine count and engine position) options •Calibrate trim sensor •Water pressure transducer (ONLY if equipped with water pressure...

  • Page 17: Basic Setup And Operation

    Basic Setup and Operation...

  • Page 18: Power Up

    Power Up The displays and settings in this digital gauge are controlled by a five-button keypad. The buttons are: •UP and DOWN — Use to scroll through and select menu items •MENU — Use to open basic menu to set up display pages •PAGES / ENTER —...

  • Page 19: Boat Setup

    Boat Setup Engine and Fuel Tank Configuration Setup Menu When the I-Command Digital gauge powers up for the first time, the screen will show the Boat Setup menu. Boat Setup Boat Setup must be complete before proceeding. 1. Press ENTER. Press the DOWN button to select the engine and tank configuration for the boat.
  • Page 20 Setting Fuel Tank Size 3. Press and hold the UP button to enter the fuel tank capacity. Use the DOWN button if necessary to make additional adjustments. 1 Eng / 1 Tank 4. Press ENTER to set the tank capacity. Repeat these steps for additional 1 Eng / 2 Tanks Setting Tank Size 2 Eng / 1 Tank...

  • Page 21: Engine Data

    Engine Data The I-Command system can monitor up to three engines. The ENGINE DATA option controls which engine is monitored. Note: This option will only display in multi-engine set-ups. 1. Press MENU. Use the UP or DOWN buttons and select SYSTEM SETUP. Press ENTER.

  • Page 22: Information Displays

    Information Displays Pages are an essential part of the I-Command Digital gauge. Press the ENTER button repeatedly to scroll through the factory default pages. There are seven factory default pages: x 100 •Tachometer - displays engine rpm 4257 •Speedometer - displays ground speed (GND:S) •Fuel Level - displays fuel level percent (FUL:L) M E N U •Engine Trim - displays engine trim percent...
  • Page 23 Engine Trim FUL:L M E N U M E N U Fuel Level Engine Trim Fuel Flow 12.78 gal / hr Eng Temp Batt Volt Ground Speed 153.2 13.6 Fuel Rem ° F M E N U M E N U MENU Fuel Flow Engine Temperature...

  • Page 24: Screen Settings

    Screen Settings Change the screen settings to improve visibility. 1. Press MENU. Use UP or DOWN buttons to select SCREEN. Press ENTER. •To change contrast, go to Step 2. •To adjust backlight go to Step 4. •To change video display go to Step 9. Change Contrast 2.
  • Page 25 Adjust Backlight 4. Use UP or DOWN buttons to select BACKLIGHT. Press ENTER. 5. Use the UP or DOWN buttons to select BLIGHT SYNC or ADJUST. Backlight Press ENTER. Contrast Rev Video For backlight synchronization go to Step 6. To adjust backlight brightness go to Step 7. M E N U Backlight Blight Sync...
  • Page 26 6. Use the UP or DOWN buttons to select OFF or ON. Turn Backlight Sync ON to synchronize the lighting of all gauges. 7. Use the UP or DOWN buttons to select ADJUST. Press ENTER. 8. Use the UP button to brighten the backlight. Use the DOWN button to dim the backlight.
  • Page 27 Reverse Video 9. Use UP or DOWN buttons to select REVERSE VIDEO. Press ENTER. 10. Press ENTER to toggle screen from dark values with light background; 11. or from light values with dark background. Press EXIT when finished. Backlight Contrast Reverse Video FUL:L FUL:L...

  • Page 28: Change Units

    Change Units This example will change the water pressure gauge to read from psi, to bar. Other units can be changed in the same manner. 1. Press MENU. Use the UP or DOWN buttons and select SYSTEM SETUP. Press ENTER. 2.
  • Page 29 3. Use the UP or DOWN buttons and select PRESSURE. 4. Use the UP or DOWN buttons and select desired units. Press ENTER. 5. Gauge will now display selected units. Speed/Dist Temperature WTR:P Imperial/US Pressure GND:S SI (Metric) Depth GPS Coord Volume M E N U M E N U...
  • Page 30 Setup Notes...

  • Page 31: Customizing Displays

    Customizing Displays...

  • Page 32: Display Fuel Economy

    Display Fuel Economy 1. Press the ENTER button repeatedly to scroll to the Fuel Flow page. Fuel Flow The center data box is Ground Speed. 12.78 gal / hr Ground Speed 2. Press MENU. Use the UP or DOWN buttons to select CUSTOMIZE. Fuel Rem Press ENTER.
  • Page 33 3. Use UP or DOWN buttons to select CENTER DATA. Press ENTER. 4. Press UP or DOWN button to select FUEL ECONOMY. Press ENTER. 5. Press EXIT twice to return to fuel manager page. Fuel Economy (MPG) is now activated. Fuel Flow 12.78 gal / hr...

  • Page 34: Add New Page

    Add New Page Page displays can be presented in analog or digital format as single, dual, or quad displays. Customize In addition to analog or digital gauge displays, seven other pages can be Pages Screen added. They are: Audio Setup System Setup •Trim Tabs - requires sending unit •GPS Position - requires GPS module...
  • Page 35 3. Use the UP or DOWN buttons to select Diagnostics. Press ENTER. 4. Press ENTER again to confirm. 5. The Engine Diagnostic page will now display. Eng Diagnostics Trim Tabs Trim Tabs Adding Page GPS Position GPS Position Engine OK Press ENTER Rudder Rudder...
  • Page 36 Add Analog Page Analog page displays allow the following data combinations: •Alt Voltage •GPS Speed (speed over ground) Customize •Atmospheric Pressure •Paddle Wheel Speed (speed over water) Pages Screen •Battery Voltage •Pitot Speed Audio Setup System Setup •Engine Temp •Tachometer •Fluid Level •Temperature •Fuel Pressure...
  • Page 37 3. Press UP button to select DUAL ANALOG. Press ENTER. 4. Press ENTER again to confirm. Single Analog The Dual Analog gauge will now display. Dual Analog Quad Analog Single Digital To change the items displayed on any single, dual or quad analog gauge, Dual Digital see “Customizing Displays”...
  • Page 38 Add Digital Page Digital page displays allow the following data combinations: •Alt Voltage •Fuel Remaining •Atmospheric Pressure •GPS Speed Customize (speed over ground) Pages •Battery Voltage •Paddle Wheel Speed Screen (speed over water) Audio Setup •Depth •Pitot Speed System Setup •Engine Temperature •Tachometer •Fuel Economy...
  • Page 39 3. Use UP or DOWN buttons to select QUAD DIGITAL. Press ENTER. 4. Press ENTER again to confirm. Single Analog The Quad Digital gauge will now display. Dual Analog Quad Analog Single Digital To change the items displayed on any single, dual or quad digital gauge, see Dual Digital “Customizing Displays”...

  • Page 40: Customizing Displays

    Customizing Displays Changing Display Defaults When adding pages, each single, dual or quad page has a default display. Use the CUSTOMIZE menu to change which items are displayed on a page. 1. Press ENTER multiple times to scroll to page to customize. Press MENU.
  • Page 41 4. Use UP or DOWN buttons to select desired display item. Press ENTER. 5. Press EXIT once to return to Step 3 and change remaining items. Press EXIT multiple times to return to display. Alt Voltage Batt Voltage Display change will now appear. Engine Temp Eng Water Press Fuel Pressure...
  • Page 42 Configure Time Display 1. Press MENU. Use UP or DOWN buttons to select SYSTEM SETUP. Press ENTER. 2. Use UP or DOWN buttons to select TIME CONFIG. Press ENTER. 3. Use UP or DOWN buttons to select: HOUR FORMAT, go to Step 4. SHOW SECONDS, go to Step 5.
  • Page 43 4. Use UP or DOWN buttons to select 12 or 24 hour display option. Press ENTER. 5. Use UP or DOWN buttons to select YES or NO. Press ENTER. Hour Format 6. Use UP or DOWN buttons to select Time Zone. 24 hrs Press ENTER.

  • Page 44: Lock Pages

    Lock Pages Viewing Pass Code This feature prevents unauthorized users from changing select gauge settings. If you have the PASS CODE, skip to step 4. 1. Press MENU. Use UP or DOWN buttons to select SYSTEM SETUP. Press ENTER. 2. Select NMEA INFO and press ENTER. 3.
  • Page 45 Lock Pages 4. Use the UP or DOWN buttons to select LOCK PAGES. Press ENTER. 5. Use the UP or DOWN buttons to change the active digit. Use the MENU button to select the next digit. Press ENTER to submit PASS CODE. 6.

  • Page 46: Accessing A Locked Page

    Accessing a Locked Page Locking pages prevents an unauthorized user from changing select gauge settings. 1. Press MENU. Use UP or DOWN buttons to select SYSTEM SETUP. 2. Select desired page and press ENTER. 3. Enter the gauge PASS CODE. Use the UP or DOWN buttons to change the active digit.
  • Page 47 4. An incorrect entry will result in an INVALID PASS CODE message. Press ENTER to start over. 5. Correct entry of pass code allows access to pages. Use UP or DOWN buttons to select desired items and make changes. 6. When finished, press ENTER to return to gauge display. Fuel Setup Refill Tank Partial Fill...

  • Page 48: Removing Pages

    Removing Pages 1. Press the ENTER button repeatedly to scroll to the page to be removed. Press MENU. Volts Volts 2. Use UP or DOWN buttons to select PAGES. BATT:V ALR:V Press ENTER. WTR: T WTR:P °F M E N U Customize Pages Screen...
  • Page 49 3. Use UP or DOWN buttons to select REMOVE PAGE. Press ENTER. 4. A confirmation message will appear. Press ENTER to remove page. Add Page Remove Page The display will return to the next page. Page Scrolling Popups Setup M E N U Removing Page Press ENTER to Remove...

  • Page 50: Page Scrolling

    Page Scrolling Pages can be viewed by manual or automatic scrolling. Manual Customize To scroll through pages manually, use the ENTER and EXIT buttons to view Pages Screen pages. Audio Setup System Setup Automatic To scroll through pages automatically, a viewing interval must be selected. 1.
  • Page 51 3. Use the UP or DOWN buttons to select SET TIME. Press ENTER. 4. Use the UP or DOWN buttons to set time. Page Scrolling Select an interval between one and sixty seconds. Press ENTER to set automatic scrolling interval. Set Time Note: To turn off automatic page scrolling, repeat the first two steps.

  • Page 52: Pop-Ups

    Pop-Ups The Pop-Up feature alerts users when changes occur in a monitored cate- gory (RPM, Engine Trim, Trim Tabs or Rudder). Pop-ups appear when a user-specified incremental measurement is met. When an increment Customize Pages changes, the main page for the category will pop up on the main display for Screen a preset duration.
  • Page 53 3. Use the UP or DOWN button to select RPM. Press ENTER. 4. Use the UP or DOWN button to select OFF to turn off the RPM pop-up, or select SET THRESHOLD. Press ENTER. 5. The threshold for RPM ranges from 50 to 3,000 RPM. Set the desired RPM value that activates the pop-up by using the UP or DOWN buttons.

  • Page 54: Stay-On Time

    Stay-on Time 1. Press MENU. Use UP or DOWN buttons to select PAGES. Press ENTER. Customize Pages Screen 2. Use the UP or DOWN button to select POPUPS SETUP. Audio Setup Press ENTER. System Setup M E N U Add Page Remove Page Page Scrolling Popups Setup...
  • Page 55 3. Use the UP or DOWN buttons to select STAY-ON TIME. Press ENTER. 4. The stay-on time ranges between two and fifteen seconds. Set the desired stay-on time using the UP or DOWN buttons. Engine Trim Press ENTER when finished. Trim Tabs Rudder Stay On Time...

  • Page 56: Sleep Mode

    Sleep Mode Sleep mode allows the I-Command gauge to enter a power-save status to keep from overdrawing the boat power source. Customize 1. Press MENU. Pages Use Up or DOWN buttons to select SYSTEM SETUP. Screen Audio Setup Press ENTER. System Setup 2.
  • Page 57 3. Use the UP or DOWN buttons to select ON or OFF. Press ENTER. Guage will return to last display. Sleep Mode M E N U M E N U...
  • Page 58 Customizing Notes...

  • Page 59: Advanced Setup And Operation

    Advanced Setup and Operation...

  • Page 60: Configure Fluid Level Sensor

    Configure Fluid Level Sensor This example illustrates Fluid Level Sensor Configuration for the second of two fuel tanks. Fluid level sensors for other fluid tanks will configure similarly. 1. Press MENU. Use the UP or DOWN buttons and select SYSTEM SETUP. Press ENTER.
  • Page 61 4. Use the UP or DOWN buttons and select UNCFG F LEV. Press ENTER. 5. Press ENTER to configure Fluid Level Sensor. 6. Use the UP or DOWN buttons to select FUEL. Press ENTER. Water Temp Water Temp Configuring Fuel Tank 1 Fuel Tank 1 Black Water UnCfg F Lev...
  • Page 62 7. Use the UP or DOWN buttons and select the tank. Press ENTER. 8. The gauge will change the tank setting and return to the BUS DEVICES list. Select Tank Proceed to “Fuel and Fluid Level Sensor Calibration” on page 61. Tank 1 Tank 2 M E N U...

  • Page 63: Fuel And Fluid Level Sensor Calibration

    Fuel and Fluid Level Sensor Calibration Fluid level sensors use the tank sending unit to calculate remaining fuel, oil, Customize water etc. Calculation is based on sending unit accuracy, capacity entered Pages Screen during setup, and liquid level in the tank. Use the FIVE POINT calibration to Audio Setup System Setup achieve best accuracy.
  • Page 64 3. The gauge will search for devices. 4. Use the UP or DOWN buttons to select the device to be calibrated. Press ENTER. 5. Use the UP or DOWN buttons and select CALIBRATE. Eng Warnings Message Change Units Press ENTER. Bus Devices Searching Sleep Mode...
  • Page 65 7. Select EMPTY LEVEL. Press ENTER. 8. Be sure the tank is EMPTY. Press ENTER. 9. Select FULL LEVEL. Empty Level Full Level Press ENTER. 10. Fill the tank. Press ENTER. M E N U Calibrating Calibrating Empty Level Empty Level Set Tank to Empty Level Set Tank to...

  • Page 66: Fuel Management

    Fuel Management Select Fuel Remaining Source Perform the following procedure on each gauge. The default setting is FLUID LEV SNSR. 1. Press MENU. Use the UP or DOWN buttons and select SYSTEM SETUP. Press ENTER. 2. Use the UP or DOWN buttons and select FUEL SETUP. Press ENTER.
  • Page 67 Use the UP or DOWN buttons to make selection. Review the following to determine which choice will work best in your application. FLUID LEV SNSR (Fluid Level Sensor) - 4. Fluid level sensor requires installation of a fuel tank level converter which Eng/Fflow uses the fuel tank sending unit to calculate remaining fuel.
  • Page 68 Fuel Management Options Use the following steps to access fuel management options. 1.Press MENU. Use UP or DOWN buttons to Select SYSTEM SETUP. Press ENTER. 2. Use UP or DOWN buttons to select FUEL SETUP. Press ENTER. 3. Use the UP or DOWN buttons to select REFILL TANK or PARTIAL FILL. Press ENTER.
  • Page 69 Refill Tank 1. Choose the Refill Tank option to recalibrate the fuel tank level after it has been filled to full capacity. Refill Tank Press the ENTER button after fuel tank has been filled. Refill Tank Partial Fill Eco Speed Src Press ENTER Note: Only supported when the memory module is used as the fuel remain- Fuel Rem Src...
  • Page 70 Economy Speed Source 1. The Economy Speed Source option allows selection of the speed mea- surement source. Eco Speed Src Notes: Water Speed Pitot Speed •Water Speed (Paddle Wheel) is best suited for low speeds. Ground Speed •Pitot Speed will work best at high speeds. •Ground Speed (GPS) works well at both high and low speeds.
  • Page 71 Reset Trip Fuel 1. The Reset Trip Fuel option resets a trip fuel usage total. Press ENTER to reset the seasonal fuel total to zero. Refill Tank Rst Trip Fuel Partial Fill Reset Seasonal Fuel Eco Speed Src Press ENTER Fuel Rem Src to reset 2.

  • Page 72: Configure Sensors

    Configure Sensors Temperature Sensor 1. Press MENU. Use the UP or DOWN buttons and select SYSTEM SETUP. Press ENTER. 2. Use the UP or DOWN buttons and select BUS DEVICES. Press ENTER. 3. The gauge will search for devices. Eng Warnings Customize Eng Warnings Change Units...
  • Page 73 4. Use the UP or DOWN buttons and select UNCFG TEMP. Press ENTER. 5. Press ENTER to configure Temperature Sensor. 6. Use the UP or DOWN buttons to make selection. Water Temp Fuel Tank 1 Press ENTER. UnCfg Temp Water Press 7.
  • Page 74 Configure Pressure Sensor 1. Press MENU. Use the UP or DOWN buttons and select SYSTEM SETUP. Press ENTER. 2. Use the UP or DOWN buttons and select BUS DEVICES. Press ENTER. 3. The gauge will search for devices. Eng Warnings Customize Eng Warnings Change Units...
  • Page 75 4. Use the UP or DOWN buttons and select UNCFG PRESS. Press ENTER. 5. Press ENTER to configure Pressure Sensor. Water Temp 6. Use the UP or DOWN buttons to make selection. Fuel Tank 1 Press ENTER. UnCfg Press Water Press Oil Tank 7.

  • Page 76: Change Ranges

    Change Ranges This example will change the water pressure gauge to read from 0 – 60 psi, to 0 – 30 psi. Speed ranges and other pressure ranges can be changed in the same manner. 1. Press the ENTER button repeatedly to scroll to the page to be chnaged. 2.
  • Page 77 4. Use the UP or DOWN buttons and select ENG WATER PRESS. Press ENTER. 5. Use the UP or DOWN buttons and select desired pressure range. Press ENTER. 6. Gauge will now display selected range. Eng Water Press 0-15 psi Eng Oil Press 0-30 psi WTR:P...

  • Page 78: Winterize

    Winterize I-Command digital gauges (with software version 1.4.0 or higher) provide a winterize feature for 2008 or newer V4 and V6 models only. Engine must be running to use this option. Refer to Outboard Operator's Guide for complete procedure and Safety Precautions.
  • Page 79 4. Use the UP or DOWN buttons and select engine to winterize. Press ENTER. 5. The gauge will display WINTERIZE menu. Press ENTER. 6. Press ENTER again. Water Temp Winterization Fuel Tank 1 Press ENTER Winterize Evinrude Port Winterize to Start Evinrude Center the Process Evinrude Stbd...
  • Page 80 7. The gauge will display WINTERIZATION message. 8. When prompted, engage NEUTRAL only button on throttle and advance THROTTLE ONLY to at least 50%. 9. Gauge will display WINTERIZATION IN PROGRESS message. Winterization Receiving Data Winterize to Start 10. Gauge will display WINTERIZATION IS COMPLETE message. the Process Press EXIT to return to BUS DEVICES menu.

  • Page 81: Audio Settings

    Audio Settings The I-Command Digital gauge will emit audible sounds during operation. The key sounds can be turned OFF or ON. 1. Press MENU. Use the UP or DOWN buttons to select AUDIO SETUP. Press ENTER. 2. Use the UP or DOWN buttons to select KEY SOUNDS. Press ENTER.

  • Page 82: Reset Values

    Reset Values RESET VALUES will not clear Engine/Tank configuration or the sensor set- tings that were previously calibrated or configured. Customize 1. Press MENU. Pages Screen Use UP or DOWN buttons to select SYSTEM SETUP. Audio Setup System Setup Press ENTER. 2.
  • Page 83 3. Use UP or DOWN buttons to select PAGES, SETTINGS or ALL. Press ENTER. Select PAGES to reset the seven factory default pages. Sel Option Select SETTINGS to reset Fuel Remaining Source, Fuel Economy Speed Pages Source, Keypad Sounds, Sleep Mode, Fluid Level Warnings and Sonar Settings Alarms.

  • Page 84: Sonar Alarms

    Sonar Alarms Sonar alarms are available to aid in avoiding underwater objects or shallow operating conditions. A transducer or triducer is required for sonar alarm functionality. Customize Pages Screen This example will set the shallow sonar alarm. Audio Setup System Setup 1.
  • Page 85 3. Use UP or DOWN buttons to select SHALLOW (or DEEP) alarm. Press ENTER. 4. Use UP or DOWN buttons to select SET DEPTH (or OFF). 5. Use UP button to set depth. Use UP or DOWN buttons to make adjustments. Press ENTER to save selection.
  • Page 86 Advanced Setup Notes...

  • Page 87: Troubleshooting

    Troubleshooting...

  • Page 88: Gauge Flashes Four Dashes

    Gauge Flashes Four Dashes 1. If the I-Command digital display flashes four dashes (– – – –) it indicates the gauge is not receiving signal from one or more devices. 2. A Network Test Kit, P/N 765023 is available to assist in troubleshooting Volts Volts network problems.

  • Page 89: Engine Warnings

    Engine Warnings The I-Command gauges monitor engine conditions and display warnings in the event of a malfunction. Refer to the outboard Operator’s Guide if any engine warnings are displayed. WARNING MESSAGE POSSIBLE CAUSE / PROCEDURE DISPLAYED A “Check Engine” condition may be activated when a critical engine con- dition occurs, or when a service is required: ·...

  • Page 90: Evinrude E-Tec Engine Warnings

    Evinrude E-TEC Engine Warnings The I-Command gauges monitor engine conditions and display warnings in the event of a malfunction. The following table lists warnings that are specific to Evinrude E-TEC models. Refer to the outboard Operator’s Guide if any engine warnings are displayed. WARNING MESSAGE DISPLAYED POSSIBLE CAUSE / PROCEDURE Throttle position sensor fault detected...
  • Page 91 WARNING MESSAGE DISPLAYED POSSIBLE CAUSE / PROCEDURE No Oil RPM reductn see dealer Oil pressure pulses in manifold not detected No Oil RPM reductn see dealer Oil system prime failure Engine temperature sensor, Air temperature sensor, Oil Sensor malfunction service soon pressure circuit or Water pressure circuit fault detected Overheat RPM reductn chk water and manual Engine temperature above range Injector malfunction see dealer...

  • Page 92: Network Troubleshooting Chart

    Network Troubleshooting Chart DESCRIPTION POSSIBLE CAUSE / PROCEDURE Vessel: Requires input from the device which supplies the data. Check that the device is present and connected to the network. Verify the device within the Bus Devices menu. See “Gauge Flashes Four Dashes” on page 86. Four dashes “----”...
  • Page 93 DESCRIPTION POSSIBLE CAUSE / PROCEDURE Water depth does not display Requires input from NMEA 2000 depth transducer. Sea water temperature does not Requires input from NMEA 2000 temperature transducer. display Requires fuel level sensor. See “Configure Fluid Level Sensor” Fuel tank level does not display on page 58 and “Fuel and Fluid Level Sensor Calibration”...
  • Page 94 Troubleshooting Notes...

  • Page 95: Updating Gauge Software

    Updating Gauge Software...

  • Page 96: Software Updates

    Software Updates Software for I-Command gauges can be updated with GPS Head Unit Kit, P/N 764592, or any Lowrance unit using an SD card. Update files are available from www.evinrude.com. Transfer files to an SD memory card, using a card reader and PC. When transfer is complete, insert the SD card into the card slot of the head unit. Check Device Data 1.
  • Page 97 4. A list of all NMEA 2000 device on the network will display. Use the arrow keys to select the device to check. Press ENT button. 5. The device information will display. Use the software number to determine if an update is needed. 6.
  • Page 98 Update Software 1. Press MENU button twice. Use the arrow keys to select BROWSE FILES. 2. Press the ENT button. The list of update files on the SD memory card will appear. Press the ENT button. Use the arrow keys to select the correct update file. Press the ENT button.
  • Page 99 4. Use the arrow keys to select YES. Press the ENT button. 5. A status bar will display the update progress. 6. When the update has finished loading, a REPROGRAM SUCCESSFUL message will display. Confirm the software update by repeating the steps in “Check Device Data” on page 94. Browse Files Files Software Update...
  • Page 100 Troubleshooting Failed Updates 1. If a gauge “times out” or does not successfully update, it will display a blank or white screen. 2. An error message will display if a device times out. If either of these conditions occur, turn OFF power to the network. Disconnect the all the gauges from the net- work at their tee connectors.
  • Page 101 4. When a blank software update screen appears, connect one gauge to the network. 5. This restores the gauge operation. If more than one gauge was blank, repeat this process for each gauge. When finished, reconnect any remain- ing gauges to the network. Software Update Software Update Updating LMF-400...
  • Page 102 Software Notes...

  • Page 103: Reference Information

    Reference Information...

  • Page 104: Abbreviation Tables

    Abbreviation Tables Use the abbreviation tables to interpret information from the I-Command gauge. Abbreviation Function Abbreviation Function AIR:T Air Temperature FRW:L:3 Fresh Water Tank 3 ALR:V Alternator voltage FUL:CP Fuel Capacity ATM:P Atmospheric Pressure FUL:E Fuel Economy BAT:C Battery current FUL:W:E Water Fuel Economy BAT:T...
  • Page 105 Abbreviation Function Abbreviation Function FRW:L:1 Fresh Water Tank 1 FUL:L:C Fuel Tank Center FRW:L:2 Fresh Water Tank 2 FUL:L:P Fuel Tank Port FUL:L:S Fuel Tank Starboard OUT:T Outside Temperature FUL:U Fuel Used PWD:S Paddlewheel speed FUL:U:C Fuel Used Center PTT:S Pitot speed FUL:U:P Fuel Used Port...

  • Page 106: Abbreviations Key

    Abbreviations Key The I-Command gauge displays data from network connected NMEA 2000 devices as follows: Display Category : Category Type : Modifier : Location /Instance An example might be: FUL : RM : P, is fuel remaining, port tank. Display category and an instance/location should always appear. Depending on the device one or both cate- gory type or modifier may or may not appear.
  • Page 107 Category Type / Location / Display Category Abbreviation Abbreviation Abbreviation Modifier Instance Fuel Remaining Fuel Used Seasonal Speed Inside Temperature Intake Torque Live Well Total Manifold Trim Trip Outside Used Paddlewheel Voltage Pitot Water Range Rated Tachometer Transmission Trim Tab Waste Water...

  • Page 108: System Information

    System Information Use the following steps to view the I-Command gauge software information. Press MENU. 1. Use the UP or DOWN buttons to select SYSTEM SETUP. Press ENTER. 2. Use the UP or DOWN buttons to select SYSTEM INFO. Press ENTER. 3.

  • Page 109: Product Warranty

    Operator's Guide; removal of parts, improper repairs, ser- vice, maintenance, or modification; use of parts or accessories not manufactured or approved by BRP that are either incompatible with Product or adversely affect its operation, performance, or durability; repairs done by anyone, including Purchaser, other than an autho- rized Dealer;...
  • Page 110 No distributor, Dealer or any other person is authorized to make any affirmation, representation or warranty regarding Product other than those contained in this limited warranty and, if made, shall not be enforceable against BRP. BRP reserves the right to modify this warranty at any time, being understood that such modification will not alter the warranty conditions applicable to the Products sold while this warranty is in effect.
  • Page 111 For assistance, please contact BRP US Inc. Consumer Support, P.O. Box 597, 10101 Science Drive, Sturtevant, WI 53177, 1-847-689-7090, or the affiliate of BRP Inc. where the Product was sold to the retail Purchaser.
  • Page 112 Owner’s Notes...
  • Page 113 *354598*...

Table of Contents