Page 5
ELECTED OUNTERS MAC A ........................276 TTACHED DDRESSES ARP I ..................... 280 AVIGATING THE NSPECTION ABLE ARP I ......................280 NSPECTION ABLE OLUMNS IP S ....................282 AVIGATING THE OURCE UARD ABLE DOC ID: 10118801 PAGE 5 OSD2790SFP OPERATOR MANUAL...
OPTICAL SYSTEMS DESIGN 1 PRODUCT DESCRIPTION This manual describes how to install and setup the OSD2790SFP Managed Ethernet Switch. To get the most out of this manual, the user should have an understanding of Ethernet networking concepts. This manual is in two parts – A Quick Start Guide section and a detailed user manual format.
One IEC power inlet module for the standard AC powered version Two IEC power inlet modules for the optional redundant AC powered version Dimensions of Enclosure (mm) 443W x 300D x 44H Weight (kg) 1022790SFP02 DOC ID: 10118801 PAGE 10 OSD2790SFP OPERATOR MANUAL...
OPTICAL SYSTEMS DESIGN 3 QUICK START GUIDE OSD2790SFP FRONT AND REAR PANELS FIGURE 1: FRONT PANEL PSU1 Status LED PSU2 Status LED Status LED Mini USB Console Port 24 x 100/1000M SFP ports with 100M/1G Link/Activity/Speed LEDs 4 x 1G Trunk/Uplink SFP ports with 100M/1G Link/Activity/Speed LEDs...
CLI OVERVIEW CONNECT TO CLI The OSD2790SFP has a Mini USB console port connector located on the front of the unit that is used for Command Line Interface (CLI) from the PC to the OSD2790SFP via the PC’s USB connector.
Page 15
OPTICAL SYSTEMS DESIGN 1. Connect the Console Port on OSD2790SFP (Mini USB) to PC with USB cable. 2. Using HyperTerminal, SecureCRT, etc to set up the following parameters. • Baud Rate: 115200 • Data Bits: 8 • Parity: None •...
Some terminal emulators like SecureCRT support the “Tab” key. At the # prompt pressing the “Tab” key will also produce a list of available commands within the command level. Partially typing a command and hitting “Tab” key will autocomplete the command. DOC ID: 10118801 PAGE 16 OSD2790SFP OPERATOR MANUAL...
The CLI will then display # clear and wait for the sub command. RESET CONFIGURATION TO FACTORY DEFAULT To reset the configuration to factory defaults; # reload defaults When the promt returns, the unit has reverted to factory defaults DOC ID: 10118801 PAGE 17 OSD2790SFP OPERATOR MANUAL...
To set the OSD2790SFP host name, the unit needs to be first set to configuration mode then enter the hostname command, then a chosen hostname. After this is entered, the units requires an ‘exit’ from configuration mode.
It is necessary to save any changes to FLASH storage in the ‘startup-config’ otherwise the changes will not take effect when the unit is powered off. To save the changes the configuration needs to be copied to the startup configuration. # copy running-config startup-config DOC ID: 10118801 PAGE 19 OSD2790SFP OPERATOR MANUAL...
The Quick Start Guide section will only show a few main or important features to get the user started and running the OSD2790SFP successfully. On the top right hand of the GUI screen there are three icons available to quickly navigate or obtain help for each GUI menu item. Note: Some screen captures will not display the full port channel count for the product.
If the multiple IP addresses are required, click Add Interface to add more IP interface. Click Save to save the configuration. Use new IP address to access the switch. PS: All configuration changes must be saved otherwise all the changes will be lost after rebooting! DOC ID: 10118801 PAGE 21 OSD2790SFP OPERATOR MANUAL...
Click admin to change the current admin account setting. If multiple users are required, click Add New User PS: All configuration changes must be saved otherwise all the changes will be lost after rebooting! DOC ID: 10118801 PAGE 22 OSD2790SFP OPERATOR MANUAL...
OPTICAL SYSTEMS DESIGN SAVE CONFIGURATION TO START-UP In the treemap below, expand the Maintenance and expand Configuration, then select Save startup-config Click Save Configuration to save the configuration on start-up. DOC ID: 10118801 PAGE 23 OSD2790SFP OPERATOR MANUAL...
OPTICAL OUTPUT OPERATION WARNING: Laser Safety: Class 1 Laser Product (SFP) per IEC 60825-1:2014 standard. Class 1 The OSD2790SFP is a Class 1 laser product. PRECAUTIONS ▲ All service personnel should be provided training as to the hazards of direct viewing of laser radiation and of the precautionary measures during servicing of equipment ▲...
OPTICAL SYSTEMS DESIGN 5 GUI CONFIGURATION • Connect the OSD2790SFP to a network using Cat5 (or greater) cable to any switch port fitted with an appropriate SFP and power the unit. • Open a web browser window (Firefox, IEx, etc) Enter the IP address of the switch on the web browser - The default IP address assigned to the OSD2790SFP is 192.168.0.99.
The help “?” button is located on the right hand side of the browser. Clicking this button will open the help menu with control syntax for the selected open directory. Clicking the door symbol will bring up the “Logout” screen. DOC ID: 10118801 PAGE 27 OSD2790SFP OPERATOR MANUAL...
255, and the allowed content is the ASCII characters from 32 to 126. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 28 OSD2790SFP OPERATOR MANUAL...
Page 29
The following modes are supported: • From any DHCPv4 interfaces The first DNS server offered from a DHCPv4 lease to a DHCPv4-enabled interface will be used. • No DNS server No DNS server will be used. DOC ID: 10118801 PAGE 29 OSD2790SFP OPERATOR MANUAL...
Page 30
Enable the DHCPv4 client by checking this box. If this option is enabled, the system will configure the IPv4 address and mask of the interface using the DHCPv4 protocol. The DHCPv4 client will announce the configured System Name as hostname to provide DNS lookup. DOC ID: 10118801 PAGE 30 OSD2790SFP OPERATOR MANUAL...
Page 31
The IPv6 network mask, in number of bits (prefix length). Valid values are between 1 and 128 bits for a IPv6 address. The field may be left blank if IPv6 operation on the interface is not desired. DOC ID: 10118801 PAGE 31 OSD2790SFP OPERATOR MANUAL...
Page 32
: Click to add a new IP route. A maximum of 128 routes is supported. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 32 OSD2790SFP OPERATOR MANUAL...
Page 33
IPv4 address. For example, '::192.1.2.34'. In addition, it can also accept a domain name address. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 33 OSD2790SFP OPERATOR MANUAL...
Save to set. • Acronym - User can set the acronym of the time zone. This is a User configurable acronym to identify the time zone. ( Range : Up to 16 characters ) DOC ID: 10118801 PAGE 34 OSD2790SFP OPERATOR MANUAL...
Month - Select the starting month. Date - Select the starting date. • • Year - Select the starting year. • Hours - Select the starting hour. • Minutes - Select the starting minute. DOC ID: 10118801 PAGE 35 OSD2790SFP OPERATOR MANUAL...
Page 36
Offset - Enter the number of minutes to add during Daylight Saving Time. ( Range: 1 to 1440 ) • Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 36 OSD2790SFP OPERATOR MANUAL...
Page 37
Informational: Send the specific messages which severity code is less or equal than Informational (6). Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 37 OSD2790SFP OPERATOR MANUAL...
The temperature at which the fan will be turn on (at the lowest possible fan speed). The value accepted is within the range of -127 to 127. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 38 OSD2790SFP OPERATOR MANUAL...
The time at which the LEDs intensity shall be set to a new intensity. If no intensity is specified for the next hour, the intensity is set to default intensity. Intensity The LEDs intensity (100% = Full power, 0% = LED off). DOC ID: 10118801 PAGE 39 OSD2790SFP OPERATOR MANUAL...
By checking the "On at errors" the LEDs will be turned on at 100% in the case that errors are logged in the system log. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 40 OSD2790SFP OPERATOR MANUAL...
The devices can exchange wakeup time information using the LLDP protocol. EEE works for ports in auto-negotiation mode, where the port is negotiated to either 1G or 100 Mbit full duplex mode. DOC ID: 10118801 PAGE 41 OSD2790SFP OPERATOR MANUAL...
Queues set will activate transmission of frames as soon as data is available. Otherwise the queue will postpone transmission until a burst of frames can be transmitted. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 42 OSD2790SFP OPERATOR MANUAL...
The description of the port. It is an ASCII string no longer than 256 characters. Link The current link state is displayed graphically. Green indicates the link is up and red that it is down. Current Link Speed Provides the current link speed of the port. DOC ID: 10118801 PAGE 43 OSD2790SFP OPERATOR MANUAL...
Page 44
PFC and Flowcontrol cannot both be enabled on the same port. Maximum Frame Size Enter the maximum frame size allowed for the switch port, including FCS. The range is 1518- 10240 bytes. DOC ID: 10118801 PAGE 44 OSD2790SFP OPERATOR MANUAL...
Page 45
Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. Click to refresh the page. Any changes made locally will be undone. DOC ID: 10118801 PAGE 45 OSD2790SFP OPERATOR MANUAL...
OPTICAL SYSTEMS DESIGN DHCP SERVER DHCP Server Mode Configuration Configuration DHCP Server Mode This page configures global mode and VLAN mode to enable/disable DHCP server per system and per VLAN. DOC ID: 10118801 PAGE 46 OSD2790SFP OPERATOR MANUAL...
: Click to add a new VLAN range : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. Click to refresh the page. Any changes made locally will be undone. DOC ID: 10118801 PAGE 47 OSD2790SFP OPERATOR MANUAL...
IP or both. Buttons : Click to add a new excluded IP range. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 48 OSD2790SFP OPERATOR MANUAL...
Display lease time of the pool. Buttons : Click to add a new DHCP pool. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 49 OSD2790SFP OPERATOR MANUAL...
Page 50
Enabled: Enable DHCP snooping mode operation. When DHCP snooping mode operation is enabled, the DHCP request messages will be forwarded to trusted ports and only allow reply packets from trusted ports. Disabled: Disable DHCP snooping mode operation. DOC ID: 10118801 PAGE 50 OSD2790SFP OPERATOR MANUAL...
Page 51
Trusted: Configures the port as trusted source of the DHCP messages. Untrusted: Configures the port as untrusted source of the DHCP messages. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 51 OSD2790SFP OPERATOR MANUAL...
Page 52
DHCP server and removes it from a DHCP message when transferring to DHCP client. It only works when DHCP relay operation mode is enabled. Disabled: Disable DHCP relay information mode operation. DOC ID: 10118801 PAGE 52 OSD2790SFP OPERATOR MANUAL...
Page 53
Drop: Drop the package when a DHCP message that already contains relay information is received. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 53 OSD2790SFP OPERATOR MANUAL...
By default setting, most groups privilege level 5 has the read-only access and privilege level 10 has the read-write access. And the system maintenance (software upload, factory defaults and etc.) need user privilege level 15. DOC ID: 10118801 PAGE 54 OSD2790SFP OPERATOR MANUAL...
Page 55
Generally, the privilege level 15 can be used for an administrator account, privilege level 10 for a standard user account and privilege level 5 for a guest account. Buttons : Click to add a new user. DOC ID: 10118801 PAGE 55 OSD2790SFP OPERATOR MANUAL...
Page 57
5, the privilege configuration should be set as JSON_RPC:[5,5,5,5] and MPLS_TP:[5,10,5,10]. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 57 OSD2790SFP OPERATOR MANUAL...
Page 58
No: Authentication is disabled and login is not possible. • Local: Use the local user database on the switch for authentication. • Radius: Use remote RADIUS server(s) for authentication. • Tacacs: Use remote TACACS+ server(s) for authentication. DOC ID: 10118801 PAGE 58 OSD2790SFP OPERATOR MANUAL...
Enable accounting of all commands with a privilege level higher than or equal to this level. Valid values are in the range 0 to 15. Leave the field empty to disable command accounting. DOC ID: 10118801 PAGE 59 OSD2790SFP OPERATOR MANUAL...
Page 60
OPTICAL SYSTEMS DESIGN Exec Enable exec (login) accounting. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 60 OSD2790SFP OPERATOR MANUAL...
Page 61
Indicates the SSH mode operation. Possible modes are: Enabled: Enable SSH mode operation. Disabled: Disable SSH mode operation. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 61 OSD2790SFP OPERATOR MANUAL...
Page 62
Upload: Upload a certificate PEM file. Possible methods are: Web Browser or URL. Generate: Generate a new self-signed RSA certificate. Certificate Pass Phrase Enter the pass phrase in this field if your uploading certificate is protected by a specific passphrase. DOC ID: 10118801 PAGE 62 OSD2790SFP OPERATOR MANUAL...
Page 63
Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. Click to refresh the page. Any changes made locally will be undone. DOC ID: 10118801 PAGE 63 OSD2790SFP OPERATOR MANUAL...
Page 64
IP address range provided in the entry. TELNET/SSH Indicates that the host can access the switch from TELNET/SSH interface if the host IP address matches the IP address range provided in the entry. DOC ID: 10118801 PAGE 64 OSD2790SFP OPERATOR MANUAL...
Page 65
OPTICAL SYSTEMS DESIGN Buttons : Click to add a new access management entry. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 65 OSD2790SFP OPERATOR MANUAL...
Page 66
Disabled: Disable SNMP mode operation. Version Indicates the SNMP supported version. Possible versions are: SNMP v1: Set SNMP supported version 1. SNMP v2c: Set SNMP supported version 2c. SNMP v3: Set SNMP supported version 3. DOC ID: 10118801 PAGE 66 OSD2790SFP OPERATOR MANUAL...
Page 67
10 and 64, but all-zeros and all-'F's are not allowed. Change of the Engine ID will clear all original local users. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 67 OSD2790SFP OPERATOR MANUAL...
Disabled: Disable SNMP trap mode operation. Version Indicates the SNMP trap supported version. Possible versions are: SNMPv1: Set SNMP trap supported version 1. SNMPv2c: Set SNMP trap supported version 2c. SNMPv3: Set SNMP trap supported version 3. DOC ID: 10118801 PAGE 68 OSD2790SFP OPERATOR MANUAL...
Page 69
1~65535. Buttons : Click to add a new access management entry. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 69 OSD2790SFP OPERATOR MANUAL...
Page 70
Indicates the SNMP access source address mask. Buttons : Click to add a new access management entry. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 70 OSD2790SFP OPERATOR MANUAL...
Page 71
SHA: An optional flag to indicate that this user uses SHA authentication protocol. The value of security level cannot be modified if entry already exists. That means must first ensure that the value is set correctly. DOC ID: 10118801 PAGE 71 OSD2790SFP OPERATOR MANUAL...
Page 72
ASCII characters from 33 to 126. Buttons : Click to add a new access management entry. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 72 OSD2790SFP OPERATOR MANUAL...
Page 73
32, and the allowed content is ASCII characters from 33 to 126. Buttons : Click to add a new access management entry. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 73 OSD2790SFP OPERATOR MANUAL...
Page 74
128. The allowed string content is digital number or asterisk(*). Buttons : Click to add a new access management entry. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 74 OSD2790SFP OPERATOR MANUAL...
Page 75
The name of the MIB view defining the MIB objects for which this request may potentially set new values. The allowed string length is 1 to 32, and the allowed content is ASCII characters from 33 to 126. DOC ID: 10118801 PAGE 75 OSD2790SFP OPERATOR MANUAL...
Page 76
OPTICAL SYSTEMS DESIGN Buttons : Click to add a new access management entry. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 76 OSD2790SFP OPERATOR MANUAL...
Page 77
1000000*(switch ID-1), for example, if the port is switch 3 port 5, the value is 2000005. Buttons : Click to add a new access management entry. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 77 OSD2790SFP OPERATOR MANUAL...
Page 78
The number of data shall be saved in the RMON. Buttons : Click to add a new access management entry. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 78 OSD2790SFP OPERATOR MANUAL...
Page 79
The method of sampling the selected variable and calculating the value to be compared against the thresholds, possible sample types are: Absolute: Get the sample directly. Delta: Calculate the difference between samples (default). Value The value of the statistic during the last sampling period. DOC ID: 10118801 PAGE 79 OSD2790SFP OPERATOR MANUAL...
Page 80
Falling event index (1-65535). Buttons : Click to add a new access management entry. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 80 OSD2790SFP OPERATOR MANUAL...
Page 81
Indicates the value of sysUpTime at the time this event entry last generated an event. Buttons : Click to add a new access management entry. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 81 OSD2790SFP OPERATOR MANUAL...
Page 82
OPTICAL SYSTEMS DESIGN NETWORK CONFIGURATION Port Security Limit Control Configuration Configuration Security Network Limit Control DOC ID: 10118801 PAGE 82 OSD2790SFP OPERATOR MANUAL...
Controls whether Limit Control is enabled on this port. Both this and the Global Mode must be set to Enabled for Limit Control to be in effect. Notice that other modules may still use the underlying port security features without enabling Limit Control on a given port. DOC ID: 10118801 PAGE 83 OSD2790SFP OPERATOR MANUAL...
Page 84
Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. Click to refresh the page. Any changes made locally will be undone. DOC ID: 10118801 PAGE 84 OSD2790SFP OPERATOR MANUAL...
Page 85
These backend (RADIUS) servers are configured on the "Configuration→Security→AAA" page. The IEEE802.1X standard defines port- based operation, but non-standard variants overcome security limitations as shall be explored below. DOC ID: 10118801 PAGE 85 OSD2790SFP OPERATOR MANUAL...
Page 87
This is the value that a port's Port VLAN ID is set to if a port is moved into the Guest VLAN. It is only changeable if the Guest VLAN option is globally enabled. Valid values are in the range [1; 4095]. DOC ID: 10118801 PAGE 87 OSD2790SFP OPERATOR MANUAL...
EAP is very flexible, in that it allows for different authentication methods, like MD5-Challenge, PEAP, and TLS. The important thing is that the authenticator (the switch) doesn't need to know which authentication method the supplicant and the authentication server are DOC ID: 10118801 PAGE 88 OSD2790SFP OPERATOR MANUAL...
- to wake up any supplicants that might be on the port. The maximum number of supplicants that can be attached to a port can be limited using the Port Security Limit Control functionality. DOC ID: 10118801 PAGE 89 OSD2790SFP OPERATOR MANUAL...
VLAN ID is immediately reverted to the original VLAN ID (which may be changed by the administrator in the DOC ID: 10118801 PAGE 90 OSD2790SFP OPERATOR MANUAL...
Page 91
Guest VLAN if the "Allow Guest VLAN if EAPOL Seen" is disabled. Port State The current state of the port. It can undertake one of the following values: Globally Disabled: NAS is globally disabled. DOC ID: 10118801 PAGE 91 OSD2790SFP OPERATOR MANUAL...
Page 92
Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. Click to refresh the page. Any changes made locally will be undone. DOC ID: 10118801 PAGE 92 OSD2790SFP OPERATOR MANUAL...
Page 94
Enabled: To reopen ports by changing the volatile port configuration of the ACL user module. Disabled: To close ports by changing the volatile port configuration of the ACL user module. The default value is "Enabled". Counter Counts the number of frames that match this ACE. DOC ID: 10118801 PAGE 94 OSD2790SFP OPERATOR MANUAL...
Page 95
: Click to save changes. : Click to undo any changes made locally and revert to previously saved values. Click to refresh the page. Any changes made locally will be undone. Click to clear the counters. DOC ID: 10118801 PAGE 95 OSD2790SFP OPERATOR MANUAL...
Page 96
Specify the rate unit. The allowed values are: pps: packets per second. kbps: Kbits per second. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 96 OSD2790SFP OPERATOR MANUAL...
Page 97
Action Indicates the forwarding action of the ACE. Permit: Frames matching the ACE may be forwarded and learned. Deny: Frames matching the ACE are dropped. Filter: Frames matching the ACE are filtered. DOC ID: 10118801 PAGE 97 OSD2790SFP OPERATOR MANUAL...
Page 98
: Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page; any changes made locally will be undone. : Click to clear the counters. : Click to remove all ACEs. DOC ID: 10118801 PAGE 98 OSD2790SFP OPERATOR MANUAL...
Page 99
OPTICAL SYSTEMS DESIGN IP Source Guard Configuration Configuration Security Network IP Source Guard IP Source Guard Configuration Configuration Security Network IP Source Guard Configuration DOC ID: 10118801 PAGE 99 OSD2790SFP OPERATOR MANUAL...
Page 100
0, it means only allow the IP packets forwarding that are matched in static entries on the specific port. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 100 OSD2790SFP OPERATOR MANUAL...
Page 101
: Click to add a new entry to the Static IP Source Guard table. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 101 OSD2790SFP OPERATOR MANUAL...
Page 103
ALL: Log all entries. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. : Click to translate all dynamic entries to static entries. DOC ID: 10118801 PAGE 103 OSD2790SFP OPERATOR MANUAL...
VLAN mode configuration web page. The log type also can be configured on per VLAN setting. Possible types are: None: Log nothing. Deny: Log denied entries. Permit: Log permitted entries. ALL: Log all entries. DOC ID: 10118801 PAGE 104 OSD2790SFP OPERATOR MANUAL...
Page 105
:Click to add a new entry to the Static IP Source Guard table : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 105 OSD2790SFP OPERATOR MANUAL...
Page 106
: Click to add a new entry to the Static IP Source Guard table. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 106 OSD2790SFP OPERATOR MANUAL...
ARP INSPECTION TABLE COLUMNS Port Switch Port Number for which the entries are displayed. VLAN ID VLAN-ID in which the ARP traffic is permitted. MAC Address User MAC address of the entry. DOC ID: 10118801 PAGE 107 OSD2790SFP OPERATOR MANUAL...
Page 108
: Click to undo any changes made locally and revert to previously saved values. : Updates the table starting from the first entry in the Dynamic ARP Inspection Table. : Updates the table, starting with the entry after the last entry currently displayed. DOC ID: 10118801 PAGE 108 OSD2790SFP OPERATOR MANUAL...
Page 109
OPTICAL SYSTEMS DESIGN AAA CONFIGURATION Configuration Security RADIUS Server Configuration Configuration Security RADIUS This page allows you to configure the RADIUS servers. DOC ID: 10118801 PAGE 109 OSD2790SFP OPERATOR MANUAL...
The UDP port to use on the RADIUS server for authentication. Set to 0 to disable authentication. Acct Port The UDP port to use on the RADIUS server for accounting. Set to 0 to disable accounting. DOC ID: 10118801 PAGE 110 OSD2790SFP OPERATOR MANUAL...
The delete button can be used to undo the addition of the new server. Buttons : Click to add a new RADIUS server. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 111 OSD2790SFP OPERATOR MANUAL...
Setting the Deadtime to a value greater than 0 (zero) will enable this feature, but only if more than one server has been configured. The secret key - up to 63 characters long - shared between the TACACS+ server and the switch. DOC ID: 10118801 PAGE 112 OSD2790SFP OPERATOR MANUAL...
The delete button can be used to undo the addition of the new server Buttons : Click to add a new RADIUS server. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 113 OSD2790SFP OPERATOR MANUAL...
The Source MAC address can be used to calculate the destination port for the frame. Check to enable the use of the Source MAC address, or uncheck to disable. By default, Source MAC Address is enabled. DOC ID: 10118801 PAGE 114 OSD2790SFP OPERATOR MANUAL...
Only full duplex ports can join an aggregation and ports must be in the same speed in each group. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 115 OSD2790SFP OPERATOR MANUAL...
Page 116
Port The switch port number. LACP Enabled Controls whether LACP is enabled on this switch port. LACP will form an aggregation when 2 or more ports are connected to the same partner. DOC ID: 10118801 PAGE 116 OSD2790SFP OPERATOR MANUAL...
Page 117
Lower number means greater priority. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 117 OSD2790SFP OPERATOR MANUAL...
OAM entity is operating in Passive mode. Active devices should not respond to OAM remote loopback commands and variable requests from a Passive peer. DOC ID: 10118801 PAGE 118 OSD2790SFP OPERATOR MANUAL...
Page 119
If the Loopback support is enabled, enabling this field will start a loopback operation for the port. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 119 OSD2790SFP OPERATOR MANUAL...
Page 120
Error Window for 'Symbol Period Error Event' must be an integer value between 1-60 and its default value is '1'. Whereas Error Threshold must be between 0-4294967295 and its default value is '0'. DOC ID: 10118801 PAGE 120 OSD2790SFP OPERATOR MANUAL...
Page 121
10-900 and its default value is '60'. Whereas Error Threshold must be between 0-65535 and its default value is '1'. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 121 OSD2790SFP OPERATOR MANUAL...
OPTICAL SYSTEMS DESIGN LOOP PROTECTION Configuration Loop Protection This page allows the user to inspect the current Loop Protection configurations, and possibly change them as well. DOC ID: 10118801 PAGE 122 OSD2790SFP OPERATOR MANUAL...
Page 123
Controls whether the port is actively generating loop protection PDU's, or whether it is just passively looking for looped PDU's. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 123 OSD2790SFP OPERATOR MANUAL...
This page allows you to configure STP system settings. The settings are used by all STP Bridge instances in the Switch. Basic Settings Protocol Version The MSTP / RSTP / STP protocol version setting. Valid values are STP, RSTP and MSTP. DOC ID: 10118801 PAGE 124 OSD2790SFP OPERATOR MANUAL...
Page 125
The condition is also cleared by a system reboot. Port Error Recovery Timeout The time to pass before a port in the error-disabled state can be enabled. Valid values are between 30 and 86400 seconds (24 hours). DOC ID: 10118801 PAGE 125 OSD2790SFP OPERATOR MANUAL...
Page 126
OPTICAL SYSTEMS DESIGN Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 126 OSD2790SFP OPERATOR MANUAL...
Page 127
The name identifying the VLAN to MSTI mapping. Bridges must share the name and revision (see below), as well as the VLAN-to-MSTI mapping configuration in order to share spanning trees for MSTI's (Intra-region). The name is at most 32 characters. DOC ID: 10118801 PAGE 127 OSD2790SFP OPERATOR MANUAL...
Page 128
A VLAN can only be mapped to one MSTI. An unused MSTI should just be left empty. (I.e. not having any VLANs mapped to it.) Example: 2,5,20-40. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 128 OSD2790SFP OPERATOR MANUAL...
Page 129
MSTI instance number, concatenated with the 6-byte MAC address of the switch forms a Bridge Identifier. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 129 OSD2790SFP OPERATOR MANUAL...
Page 130
Lower path cost ports are chosen as forwarding ports in favour of higher path cost ports. Valid values are in the range 1 to 200000000. Priority Controls the port priority. This can be used to control priority of ports having identical port cost. (See above). DOC ID: 10118801 PAGE 130 OSD2790SFP OPERATOR MANUAL...
Page 131
Transition to the forwarding state is faster for point-to-point LANs than for shared media. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 131 OSD2790SFP OPERATOR MANUAL...
Page 132
Controls the port priority. This can be used to control priority of ports having identical port cost. (See above). Buttons : Click to retrieve settings for a specific MSTI. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 132 OSD2790SFP OPERATOR MANUAL...
The name used for indexing the profile table. Each entry has the unique name which is composed of at maximum 16 alphabetic and numeric characters. At least one alphabet must be present. DOC ID: 10118801 PAGE 133 OSD2790SFP OPERATOR MANUAL...
Page 134
: Click to add new IPMC profile. Specify the name and configure the new entry. Click "Save". : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 134 OSD2790SFP OPERATOR MANUAL...
Page 135
Start Address The starting IPv4/IPv6 Multicast Group Address that will be used as an address range. End Address The ending IPv4/IPv6 Multicast Group Address that will be used as an address range. DOC ID: 10118801 PAGE 135 OSD2790SFP OPERATOR MANUAL...
Page 136
: Refreshes the displayed table starting from the input fields. : Updates the table starting from the first entry in the IPMC Profile Address Configuration. : Updates the table, starting with the entry after the last entry currently displayed. DOC ID: 10118801 PAGE 136 OSD2790SFP OPERATOR MANUAL...
PC sends an IGMP/MLD report message to Switch A to join the appropriate multicast group address. Uplink ports that send and receive multicast data to and from the multicast VLAN are called MVR source ports. DOC ID: 10118801 PAGE 137 OSD2790SFP OPERATOR MANUAL...
Page 138
Specify whether the traversed IGMP/MLD control frames will be sent as Untagged or Tagged with MVR VID. The default is Tagged. Priority Specify how the traversed IGMP/MLD control frames will be sent in prioritized manner. The default Priority is 0. DOC ID: 10118801 PAGE 138 OSD2790SFP OPERATOR MANUAL...
Page 139
: Click to add new MVR VLAN. Specify the VID and configure the new entry. Click "Save". : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 139 OSD2790SFP OPERATOR MANUAL...
Page 141
Enable unregistered IPMCv4 traffic flooding. The flooding control takes effect only when IGMP Snooping is enabled. When IGMP Snooping is disabled, unregistered IPMCv4 traffic flooding is always active in spite of this setting. DOC ID: 10118801 PAGE 141 OSD2790SFP OPERATOR MANUAL...
Page 142
Enable to limit the number of multicast groups to which a switch port can belong. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 142 OSD2790SFP OPERATOR MANUAL...
VLAN. When the IPv4 management address is not set, system uses the first available IPv4 management address. Otherwise, system uses a pre-defined value. By default, this value will be 192.0.2.1. DOC ID: 10118801 PAGE 143 OSD2790SFP OPERATOR MANUAL...
Page 144
Unsolicited Report Interval. The Unsolicited Report Interval is the time between repetitions of a host's initial report of membership in a group. The allowed range is 0 to 31744 seconds, default unsolicited report interval is 1 second. DOC ID: 10118801 PAGE 144 OSD2790SFP OPERATOR MANUAL...
Page 145
: Refreshes the displayed table starting from the input fields. : Updates the table starting from the first entry in the IPMC Profile Address Configuration. : Updates the table, starting with the entry after the last entry currently displayed. DOC ID: 10118801 PAGE 145 OSD2790SFP OPERATOR MANUAL...
Page 146
You can inspect the rules of the designated profile by using the following button: : List the rules associated with the designated profile. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 146 OSD2790SFP OPERATOR MANUAL...
Page 147
OPTICAL SYSTEMS DESIGN MLD SNOOPING MLD Snooping Configuration Configuration IPMC MLD Snooping Basic Configuration This page provides MLD Snooping related configuration. Snooping Enabled Enable the Global MLD Snooping. DOC ID: 10118801 PAGE 147 OSD2790SFP OPERATOR MANUAL...
Page 148
Enable to limit the number of multicast groups to which a switch port can belong. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 148 OSD2790SFP OPERATOR MANUAL...
It indicates the MLD control frame priority level generated by the system. These values can be used to prioritize different classes of traffic. The allowed range is 0 (best effort) to 7 (highest), default interface priority value is 0. DOC ID: 10118801 PAGE 149 OSD2790SFP OPERATOR MANUAL...
Page 150
: Refreshes the displayed table starting from the input fields. : Updates the table starting from the first entry in the IPMC Profile Address Configuration. : Updates the table, starting with the entry after the last entry currently displayed. DOC ID: 10118801 PAGE 150 OSD2790SFP OPERATOR MANUAL...
Page 151
You can inspect the rules of the designated profile by using the following button: : List the rules associated with the designated profile. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 151 OSD2790SFP OPERATOR MANUAL...
OPTICAL SYSTEMS DESIGN LLDP LLDP CONFIGURATION Configuration LLDP This page allows the user to inspect and configure the current LLDP interface settings. DOC ID: 10118801 PAGE 152 OSD2790SFP OPERATOR MANUAL...
CDP TLV "Address" is mapped to the LLDP "Management Address" field. The CDP address TLV can contain multiple addresses, but only the first address is shown in the LLDP neighbors table. CDP TLV "Port ID" is mapped to the LLDP "Port ID" field. DOC ID: 10118801 PAGE 153 OSD2790SFP OPERATOR MANUAL...
Page 154
Optional TLV: When checked the "management address" is included in LLDP information transmitted. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 154 OSD2790SFP OPERATOR MANUAL...
The interface name to which the configuration applies. Capabilities When checked the switch's capabilities is included in LLDP-MED information transmitted. Policies When checked the configured policies for the interface is included in LLDP-MED information transmitted. DOC ID: 10118801 PAGE 156 OSD2790SFP OPERATOR MANUAL...
NAD83/MLLW: North American Datum 1983, CRS Code 4269, Prime Meridian Name: Greenwich; The associated vertical datum is Mean Lower Low Water (MLLW). This datum pair is to be used when referencing locations on water/sea/ocean. DOC ID: 10118801 PAGE 157 OSD2790SFP OPERATOR MANUAL...
Street suffix - Example: Ave, Pl. House no. House number - Example: 21. House no. suffix House number suffix - Example: A, 7/1. Landmark Landmark or vanity address - Example: University of Sydney. DOC ID: 10118801 PAGE 158 OSD2790SFP OPERATOR MANUAL...
Emergency Call Service ELIN identifier data format is defined to carry the ELIN identifier as used during emergency call setup to a traditional CAMA or ISDN trunk-based PSAP. This format consists of a numerical digit string, corresponding to the ELIN to be used for emergency calling. DOC ID: 10118801 PAGE 159 OSD2790SFP OPERATOR MANUAL...
Check to delete the policy. It will be deleted during the next save. Policy ID ID for the policy. This is auto generated and shall be used when selecting the policies that shall be mapped to the specific interfaces. DOC ID: 10118801 PAGE 160 OSD2790SFP OPERATOR MANUAL...
Page 161
The tagged frame format also includes priority tagged frames as defined by IEEE 802.1Q-2003. VLAN ID VLAN identifier (VID) for the interface as defined in IEEE 802.1Q-2003. DOC ID: 10118801 PAGE 161 OSD2790SFP OPERATOR MANUAL...
Buttons : Click to add new Policy : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 162 OSD2790SFP OPERATOR MANUAL...
Configure aging time by entering a value here in seconds; for example, Age time seconds. The allowed range is 10 to 1000000 seconds. Disable the automatic aging of dynamic entries by checking Disable automatic aging. DOC ID: 10118801 PAGE 163 OSD2790SFP OPERATOR MANUAL...
Adding a New Static Entry Click to add a new entry to the static MAC table. Specify the VLAN ID, MAC address, and port members for the new entry. Click "Save". DOC ID: 10118801 PAGE 164 OSD2790SFP OPERATOR MANUAL...
Page 165
: Click to add a new entry to the static MAC table. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. : Refreshes the displayed table starting from the input fields. DOC ID: 10118801 PAGE 165 OSD2790SFP OPERATOR MANUAL...
Spaces are allowed in between the delimiters. Ethertype for Custom S-ports This field specifies the ethertype/TPID (specified in hexadecimal) used for Custom S-ports. The setting is in force for all ports whose Port Type is set to S-Custom-Port. DOC ID: 10118801 PAGE 166 OSD2790SFP OPERATOR MANUAL...
Can be configured to be VLAN tag unaware, C-tag aware, S-tag aware, or S-custom-tag aware • Ingress filtering can be controlled • Ingress acceptance of frames and configuration of egress tagging can be configured independently DOC ID: 10118801 PAGE 167 OSD2790SFP OPERATOR MANUAL...
Page 168
VLAN ID embedded in the tag. Priority-tagged frames are classified to the Port VLAN. If the port is configured to accept Tagged Only frames (see Ingress Acceptance below), frames without this TPID are dropped. DOC ID: 10118801 PAGE 168 OSD2790SFP OPERATOR MANUAL...
Page 169
Hybrid port will become member of all VLANs, and is therefore set to 1-4095. The field may be left empty, which means that the port will not become member of any VLANs. DOC ID: 10118801 PAGE 169 OSD2790SFP OPERATOR MANUAL...
Page 170
By default, the field is left blank, which means that the port may become a member of all possible VLANs. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 170 OSD2790SFP OPERATOR MANUAL...
Mapping Group. This will enable all VLAN Translation mappings of that group (if any) on the selected switch port. The displayed settings are: Port The Port column shows the list of ports for which you can configure the VLAN Translation Mapping Group. DOC ID: 10118801 PAGE 171 OSD2790SFP OPERATOR MANUAL...
Page 172
Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to save changes. : Refreshes the displayed table starting from the input fields. DOC ID: 10118801 PAGE 172 OSD2790SFP OPERATOR MANUAL...
Page 173
: Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Refreshes the displayed table starting from the input fields. : Click to remove all VLAN Translation mappings. DOC ID: 10118801 PAGE 173 OSD2790SFP OPERATOR MANUAL...
Private VLAN, check the box. To remove or exclude the port from the Private VLAN, make sure the box is unchecked. By default, no ports are members, and all boxes are unchecked. DOC ID: 10118801 PAGE 174 OSD2790SFP OPERATOR MANUAL...
Page 175
: Click to add a new entry to the static MAC table. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. : Refreshes the displayed table starting from the input fields. DOC ID: 10118801 PAGE 175 OSD2790SFP OPERATOR MANUAL...
3 seconds. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. : Refreshes the displayed table starting from the input fields. DOC ID: 10118801 PAGE 176 OSD2790SFP OPERATOR MANUAL...
To remove or exclude the port from the mapping, make sure the box is unchecked. By default, no ports are members, and all boxes are unchecked. DOC ID: 10118801 PAGE 177 OSD2790SFP OPERATOR MANUAL...
Page 178
3 seconds. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. : Refreshes the displayed table starting from the input fields. DOC ID: 10118801 PAGE 178 OSD2790SFP OPERATOR MANUAL...
Page 179
Valid values for etype range between 0x0600 and 0xffff LLC: Valid value in this case is comprised of two different sub-values. a. DSAP: 1-byte long string (0x00-0xff) b. SSAP: 1-byte long string (0x00-0xff) DOC ID: 10118801 PAGE 179 OSD2790SFP OPERATOR MANUAL...
Page 180
3 seconds. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. : Refreshes the displayed table starting from the input fields. DOC ID: 10118801 PAGE 180 OSD2790SFP OPERATOR MANUAL...
Page 181
Group Name, VLAN ID and port members can be configured as needed. Legal values for a VLAN ID are 1 through 4095. button can be used to undo the addition of new entry. The maximum possible Group to VLAN mappings are limited to 256. DOC ID: 10118801 PAGE 181 OSD2790SFP OPERATOR MANUAL...
Page 182
3 seconds. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. : Refreshes the displayed table starting from the input fields. DOC ID: 10118801 PAGE 182 OSD2790SFP OPERATOR MANUAL...
Page 183
The IP subnet to VLAN ID mapping entry is enabled when you click on "Save". The button can be used to undo the addition of new mappings. The maximum possible IP subnet to VLAN ID mappings are limited to 128. DOC ID: 10118801 PAGE 183 OSD2790SFP OPERATOR MANUAL...
Page 184
3 seconds. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. : Refreshes the displayed table starting from the input fields. DOC ID: 10118801 PAGE 184 OSD2790SFP OPERATOR MANUAL...
Page 186
"Both". Changing the discovery protocol to "OUI" or "LLDP" will restart auto detect process. Possible discovery protocols are: OUI: Detect telephony device by OUI address. LLDP: Detect telephony device by LLDP. Both: Both OUI and LLDP. DOC ID: 10118801 PAGE 186 OSD2790SFP OPERATOR MANUAL...
Page 187
OPTICAL SYSTEMS DESIGN Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 187 OSD2790SFP OPERATOR MANUAL...
Page 188
The allowed string length is 0 to 32. Buttons : Click to add a new access management entry. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 188 OSD2790SFP OPERATOR MANUAL...
OPTICAL SYSTEMS DESIGN QOS INGRESS PORT CLASSIFICATION Configuration Port Classification This page allows you to configure the basic QoS Ingress Classification settings for all switch ports. DOC ID: 10118801 PAGE 189 OSD2790SFP OPERATOR MANUAL...
Page 190
If the port is VLAN aware and the frame is tagged, then the frame is classified to the DEI value in the tag. Otherwise the frame is classified to the default DEI value. DOC ID: 10118801 PAGE 190 OSD2790SFP OPERATOR MANUAL...
Page 191
Click to Enable DSCP Based QoS Ingress Port Classification. WRED Group Controls the WRED group membership. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 191 OSD2790SFP OPERATOR MANUAL...
Page 192
Controls the unit of measure for the port policer rate as kbps, Mbps, fps or kfps. Flow Control If flow control is enabled and the port is in flow control mode, then pause frames are sent instead of discarding frames. DOC ID: 10118801 PAGE 192 OSD2790SFP OPERATOR MANUAL...
Page 193
OPTICAL SYSTEMS DESIGN Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 193 OSD2790SFP OPERATOR MANUAL...
Page 194
This field is only shown if at least one of the queue policers are enabled. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 194 OSD2790SFP OPERATOR MANUAL...
Page 195
The logical port for the settings contained in the same row. Click on the port number in order to configure the schedulers. Mode Shows the scheduling mode for this port. Shows the weight for this queue and port. DOC ID: 10118801 PAGE 195 OSD2790SFP OPERATOR MANUAL...
Page 196
OPTICAL SYSTEMS DESIGN Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 196 OSD2790SFP OPERATOR MANUAL...
Page 197
Click on the port number in order to configure the shapers. Shows "-" for disabled or actual queue shaper rate - e.g. "800 Mbps". Port Shows "-" for disabled or actual port shaper rate - e.g. "800 Mbps". DOC ID: 10118801 PAGE 197 OSD2790SFP OPERATOR MANUAL...
Page 198
Click on the port number in order to configure tag remarking. Mode Shows the tag remarking mode for this port. Classified: Use classified PCP/DEI values. Default: Use default PCP/DEI values. Mapped: Use mapped versions of QoS class and DP level. DOC ID: 10118801 PAGE 198 OSD2790SFP OPERATOR MANUAL...
Page 199
In Ingress settings you can change ingress translation and classification settings for individual ports. There are two configuration parameters available in Ingress: 1. Translate 2. Classify 1. Translate To Enable the Ingress Translation click the checkbox. DOC ID: 10118801 PAGE 199 OSD2790SFP OPERATOR MANUAL...
Page 200
Remap DP Unaware: DSCP from analyzer is remapped and frame is remarked with remapped DSCP value. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 200 OSD2790SFP OPERATOR MANUAL...
Page 202
QoS class value can be any of (0-7) Drop Precedence Level (0-1) Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 202 OSD2790SFP OPERATOR MANUAL...
Page 204
Select the DSCP value from select menu to which you want to remap. DSCP value ranges form 0 to 63. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 204 OSD2790SFP OPERATOR MANUAL...
Page 205
DSCP DP3 Select the classified DSCP value (0-63) for Drop Precedence Level 3. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 205 OSD2790SFP OPERATOR MANUAL...
Page 206
Indicates (VLAN ID), either a specific VID or range of VIDs. VID can be in the range 1-4095 or 'Any' Priority Code Point: Valid values of PCP are specific (0, 1, 2, 3, 4, 5, 6, 7) or range (0-1, 2-3, 4-5, 6-7, 0-3, 4-7) or 'Any'. DOC ID: 10118801 PAGE 206 OSD2790SFP OPERATOR MANUAL...
Page 207
: Moves the QCE up the list. : Moves the QCE down the list. : Deletes the QCE. : The lowest plus sign adds a new entry at the bottom of the QCE listings. DOC ID: 10118801 PAGE 207 OSD2790SFP OPERATOR MANUAL...
Page 208
OPTICAL SYSTEMS DESIGN GLOBAL STORM POILCER CONFIGURATION Configuration Storm Policing DOC ID: 10118801 PAGE 208 OSD2790SFP OPERATOR MANUAL...
Controls the unit of measure for the port storm policer rate as fps, kfps, kbps or Mbps. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 209 OSD2790SFP OPERATOR MANUAL...
Page 210
OPTICAL SYSTEMS DESIGN WRED – WEIGHTED RANDOM EARLY DETECTION HELP Configuration WRED DOC ID: 10118801 PAGE 210 OSD2790SFP OPERATOR MANUAL...
Drop Probability: Max controls the drop probability just below 100% fill level. Fill Level: Max controls the fill level where drop probability reaches 100%. RED DROP PROBABILITY FUNCTION The following illustration shows the drop probability versus fill level function with associated parameters. DOC ID: 10118801 PAGE 211 OSD2790SFP OPERATOR MANUAL...
Page 212
The drop probability for frames increases linearly from zero (at Min average queue filling level) to Max Drop Probability or Fill Level. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 212 OSD2790SFP OPERATOR MANUAL...
30 seconds. Valid values are in the range 100 to 86400. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 213 OSD2790SFP OPERATOR MANUAL...
3. Oscillator: Select an oscillator independent of SyncE for frequency control, if supported by the 4. LTC phase: Select Local Time Counter (LTC) phase control (assumes that the frequency is locked by means of SyncE) DOC ID: 10118801 PAGE 214 OSD2790SFP OPERATOR MANUAL...
If true, one-way measurements are used. This parameter applies only to a slave. In one-way mode no delay measurements are performed, i.e. this is applicable only if frequency synchronization is needed. The master always responds to delay requests. DOC ID: 10118801 PAGE 215 OSD2790SFP OPERATOR MANUAL...
Page 216
Priority Code Point value used for PTP frames. Buttons : Click to create a new clock instance. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 216 OSD2790SFP OPERATOR MANUAL...
When GVRP is enabled, a maximum number of VLANs supported by GVRP is specified. By default this number is 20. This number can only be changed when GVRP is turned off. Buttons : Click to save changes. DOC ID: 10118801 PAGE 217 OSD2790SFP OPERATOR MANUAL...
Page 218
Mode can be either 'Disabled' or 'GVRP enabled'. These values turn the GVRP feature off or on respectively for the port in question. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values DOC ID: 10118801 PAGE 218 OSD2790SFP OPERATOR MANUAL...
The maximum number of data bytes that can be sent in a single sample datagram. This should be set to a value that avoids fragmentation of the sFlow datagrams. Valid range is 200 to 1468 bytes with default being 1400 bytes. DOC ID: 10118801 PAGE 220 OSD2790SFP OPERATOR MANUAL...
: Click to refresh the page. Note that unsaved changes will be lost. : Click to save changes. Note that sFlow configuration is not persisted to non- volatile memory. : Click to undo any changes made locally and revert to previously saved values. DOC ID: 10118801 PAGE 221 OSD2790SFP OPERATOR MANUAL...
In disabled mode, UDLD functionality doesn't exists on port. • Normal In normal mode, if the link state of the port was determined to be unidirectional, it will not affect the port state. DOC ID: 10118801 PAGE 222 OSD2790SFP OPERATOR MANUAL...
Page 223
(Default value is 7 seconds) (Currently default time interval is supported, due to lack of detailed information in RFC 5171). Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values DOC ID: 10118801 PAGE 223 OSD2790SFP OPERATOR MANUAL...
If the temperature goes above the specified temperature the alarm will be triggered. Temperature value saved only when the temperature alarm is enabled. Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values DOC ID: 10118801 PAGE 225 OSD2790SFP OPERATOR MANUAL...
The system name configured in Configuration | System | Information | System Name. Location The system location configured in Configuration | System | Information | System Location. MAC Address The MAC Address of this switch. Chip ID The Chip ID of this switch. DOC ID: 10118801 PAGE 226 OSD2790SFP OPERATOR MANUAL...
Page 227
The date when the switch software was produced. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately DOC ID: 10118801 PAGE 227 OSD2790SFP OPERATOR MANUAL...
Page 228
SVG Wiki for more information on browser support. Specifically, at the time of writing, Microsoft Internet Explorer will need to have a plugin installed to support SVG. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. DOC ID: 10118801 PAGE 228 OSD2790SFP OPERATOR MANUAL...
Page 229
The address type of the entry. This may be LINK or IPv4. Address The current address of the interface (of the given type). Status The status flags of the interface (and/or address). DOC ID: 10118801 PAGE 229 OSD2790SFP OPERATOR MANUAL...
Page 230
The Link (MAC) address for which a binding to the IP address given exist. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately DOC ID: 10118801 PAGE 230 OSD2790SFP OPERATOR MANUAL...
The level of the system log entry. Info: The system log entry is belonged information level. Warning: The system log entry is belonged warning level. Error: The system log entry is belonged error level. DOC ID: 10118801 PAGE 231 OSD2790SFP OPERATOR MANUAL...
Page 232
: Updates the table entries, ending at the last entry currently displayed. : Updates the table entries, starting from the last entry currently displayed. : Updates the table entries, ending at the last available entry. DOC ID: 10118801 PAGE 232 OSD2790SFP OPERATOR MANUAL...
Page 233
: Updates the system log entry to the previous available entry ID. : Updates the system log entry to the next available entry ID. : Updates the system log entry to the last available entry ID. DOC ID: 10118801 PAGE 233 OSD2790SFP OPERATOR MANUAL...
This page provides the current status for EEE. Local Port This is the logical port number for this row. Link Shows if the link is up for the port (green = link up, red = link down). DOC ID: 10118801 PAGE 234 OSD2790SFP OPERATOR MANUAL...
Page 235
Shows if the system is currently saving power due to PerfectReach. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately. DOC ID: 10118801 PAGE 235 OSD2790SFP OPERATOR MANUAL...
Shows the temperature of the temperature sensor(s) in Celsius degrees. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately. DOC ID: 10118801 PAGE 236 OSD2790SFP OPERATOR MANUAL...
This page provides an overview of the current switch port states. The port states are illustrated as follows: Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately. DOC ID: 10118801 PAGE 237 OSD2790SFP OPERATOR MANUAL...
Page 238
The number of received frames filtered by the forwarding process. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Clears the counters for all ports. : Click to refresh the page immediately. DOC ID: 10118801 PAGE 238 OSD2790SFP OPERATOR MANUAL...
Page 239
The number of received and transmitted packets per queue. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Clears the counters for all ports. : Click to refresh the page immediately. DOC ID: 10118801 PAGE 239 OSD2790SFP OPERATOR MANUAL...
Page 240
QCE may not be available, in that case it shows conflict status as 'Yes', otherwise it is always 'No'. Please note that conflict can be resolved by releasing the H/W resources required to add QCL entry on pressing 'Resolve Conflict' button. DOC ID: 10118801 PAGE 240 OSD2790SFP OPERATOR MANUAL...
Page 241
: Click to release the resources required to add QCL entry, in case the conflict status for any QCL entry is 'yes'. : Clears the counters for all ports. : Click to refresh the page immediately. DOC ID: 10118801 PAGE 241 OSD2790SFP OPERATOR MANUAL...
The number of received and transmitted (good and bad) broadcast packets. Rx and Tx Pause A count of the MAC Control frames received or transmitted on this port that have an opcode indicating a PAUSE operation. DOC ID: 10118801 PAGE 242 OSD2790SFP OPERATOR MANUAL...
Long frames are frames that are longer than the configured maximum frame length for this port. TRANSMIT ERROR COUNTERS Tx Drops The number of frames dropped due to output buffer congestion. Tx Late/Exc. Coll. The number of frames dropped due to excessive or late collisions. DOC ID: 10118801 PAGE 243 OSD2790SFP OPERATOR MANUAL...
Page 244
The port select box determines which port is affected by clicking the buttons. Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Clears the counters for the selected port. : Click to refresh the page immediately. DOC ID: 10118801 PAGE 244 OSD2790SFP OPERATOR MANUAL...
A duplicate Event Notification OAMPDU is indicated as an Event Notification OAMPDU with a Sequence Number field that is identical to the previously transmitted Event Notification OAMPDU Sequence Number. DOC ID: 10118801 PAGE 245 OSD2790SFP OPERATOR MANUAL...
Page 246
The port select box determines which port is affected by clicking the buttons. Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Clears the counters for the selected port. : Click to refresh the page immediately. DOC ID: 10118801 PAGE 246 OSD2790SFP OPERATOR MANUAL...
When in forwarding state, Device is forwarding non-OAMPDUs to higher sublayer. When in loopback, Device is looping back non-OAMPDUs to the lower sublayer. When in discarding state, Device is discarding non-OAMPDUs. Organizational Unique Identification 24-bit Organizationally Unique Identifier of the vendor. DOC ID: 10118801 PAGE 247 OSD2790SFP OPERATOR MANUAL...
Page 248
The port select box determines which port is affected by clicking the buttons. Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately. DOC ID: 10118801 PAGE 248 OSD2790SFP OPERATOR MANUAL...
Page 249
1) The default value is one frame error. 2) The lower bound is zero frame errors. 3) The upper bound is unspecified. Frame errors This four-octet field indicates the number of detected errored frames in the period. DOC ID: 10118801 PAGE 249 OSD2790SFP OPERATOR MANUAL...
Page 250
OAM sublayer was reset. Event Seconds Summary Time Stamp This two-octet field indicates the time reference when the event was generated, in terms of 100 ms intervals, encoded as a 16-bit unsigned integer. DOC ID: 10118801 PAGE 250 OSD2790SFP OPERATOR MANUAL...
Page 251
The port select box determines which port is affected by clicking the buttons. Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to clear the data. : Click to refresh the page immediately. DOC ID: 10118801 PAGE 251 OSD2790SFP OPERATOR MANUAL...
OPTICAL SYSTEMS DESIGN DHCP DHCP SERVER DHCP Server Statistics Monitor DHCP Server Statistics This page displays the database counters and the number of DHCP messages sent and received by DHCP server. DOC ID: 10118801 PAGE 252 OSD2790SFP OPERATOR MANUAL...
Number of DHCP DISCOVER messages received. REQUEST Number of DHCP REQUEST messages received. DECLINE Number of DHCP DECLINE messages received. RELEASE Number of DHCP RELEASE messages received. INFORM Number of DHCP INFORM messages received. DOC ID: 10118801 PAGE 253 OSD2790SFP OPERATOR MANUAL...
: Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to clear HHCP Message Received Counters and DHCP Message Sent Counters. : Click to refresh the page immediately. DOC ID: 10118801 PAGE 254 OSD2790SFP OPERATOR MANUAL...
Type of binding. Possible types are Automatic, Manual, Expired. State State of binding. Possible states are Committed, Allocated, Expired. Pool Name The pool that generates the binding. Server ID Server IP address to service the binding. DOC ID: 10118801 PAGE 255 OSD2790SFP OPERATOR MANUAL...
Page 256
: Click to clear all Automatic bindings and Change them to Expired bindings. : Click to clear all Manual bindings and Change them to Expired bindings. : Click to clear all Expired bindings and free them. DOC ID: 10118801 PAGE 256 OSD2790SFP OPERATOR MANUAL...
Display IP addresses declined by DHCP clients. Declined IP List of IP addresses declined. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately. DOC ID: 10118801 PAGE 257 OSD2790SFP OPERATOR MANUAL...
Switch Port Number for which the entries are displayed. IP Address User IP address of the entry. IP Subnet Mask User IP subnet mask of the entry. DHCP Server Address DHCP Server address of the entry. DOC ID: 10118801 PAGE 258 OSD2790SFP OPERATOR MANUAL...
Page 259
: Click to refresh the page immediately. : Updates the table tarting from the first entry in the Dynamic DHCP snooping Table. : Updates the table entries, starting from the last entry currently displayed. DOC ID: 10118801 PAGE 259 OSD2790SFP OPERATOR MANUAL...
The number of packets whose Remote ID option did not match known Remote ID. SERVER STATISTICS Transmit To Client The number of relayed packets from server to client. Transmit Error The number of packets that resulted in error while being sent to servers. DOC ID: 10118801 PAGE 260 OSD2790SFP OPERATOR MANUAL...
Page 261
The number of packets that were dropped which were received with relay agent information Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately : Clear all statistics DOC ID: 10118801 PAGE 261 OSD2790SFP OPERATOR MANUAL...
Rx and Tx Release The number of release (option 53 with value 7) packets received and transmitted Rx and Tx Inform The number of inform (option 53 with value 8) packets received and transmitted. DOC ID: 10118801 PAGE 262 OSD2790SFP OPERATOR MANUAL...
Page 263
The port select box determines which port is affected by clicking the buttons. Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately : Clear all statistics DOC ID: 10118801 PAGE 263 OSD2790SFP OPERATOR MANUAL...
Number of discarded packets from the interface when access management mode is enabled. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately : Clear all statistics DOC ID: 10118801 PAGE 264 OSD2790SFP OPERATOR MANUAL...
Page 265
OPTICAL SYSTEMS DESIGN NETWORK Port Security Port Security Switch Status Monitor Security Network Port Security Switch DOC ID: 10118801 PAGE 265 OSD2790SFP OPERATOR MANUAL...
Shutdown: The Port Security service is enabled by at least the Limit Control user module, and that module has indicated that the limit is exceeded. No MAC addresses can be learned on the port until it is administratively re-opened on the Limit Control configuration Web-page. DOC ID: 10118801 PAGE 266 OSD2790SFP OPERATOR MANUAL...
Page 267
If the Limit Control user module is not enabled on the port, the Limit column will show a dash (-). Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately DOC ID: 10118801 PAGE 267 OSD2790SFP OPERATOR MANUAL...
Page 268
MAC address will be removed from the MAC table. Otherwise a new age period will begin. If aging is disabled or a user module has decided to hold the MAC address indefinitely, a dash (-) will be shown. DOC ID: 10118801 PAGE 268 OSD2790SFP OPERATOR MANUAL...
Page 269
Use the port select box to select which port to show status for. Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately DOC ID: 10118801 PAGE 269 OSD2790SFP OPERATOR MANUAL...
Page 270
The current state of the port. Refer to NAS Port State for a description of the individual states. Last Source The source MAC address carried in the most recently received EAPOL frame for EAPOL-based authentication, and the most recently received frame from a new client for MAC-based authentication. DOC ID: 10118801 PAGE 270 OSD2790SFP OPERATOR MANUAL...
Page 271
If the port is moved to the Guest VLAN, "(Guest)" is appended to the VLAN ID. Read more about Guest VLANs Configuration Security Network NAS. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately DOC ID: 10118801 PAGE 271 OSD2790SFP OPERATOR MANUAL...
Guest VLANs Configuration Security Network NAS. PORT COUNTERS EAPOL Counters These supplicant frame counters are available for the following administrative states: • Force Authorized • Force Unauthorized • Port-based 802.1X • Single 802.1X • Multi 802.1X DOC ID: 10118801 PAGE 272 OSD2790SFP OPERATOR MANUAL...
Page 273
Backend Server Counters These backend (RADIUS) frame counters are available for the following administrative states: • Port-based 802.1X • Single 802.1X • Multi 802.1X • MAC-based Auth. DOC ID: 10118801 PAGE 273 OSD2790SFP OPERATOR MANUAL...
Page 274
Counts the number of times that the switch attempts to send a supplicant's first Responses dot1xAuthBackendResponses response packet to the backend server. Indicates the switch attempted communication with the backend server. Possible DOC ID: 10118801 PAGE 274 OSD2790SFP OPERATOR MANUAL...
The table is identical to and is placed next to the Port Counters table, and will be empty if no MAC address is currently selected. To populate the table, select one of the attached MAC Addresses from the table below. DOC ID: 10118801 PAGE 275 OSD2790SFP OPERATOR MANUAL...
: Click to refresh the page immediately : This button is available in the following modes: • Force Authorized • Force Unauthorized • Port-based 802.1X • Single 802.1X Click to clear the counters for the selected port. DOC ID: 10118801 PAGE 276 OSD2790SFP OPERATOR MANUAL...
Page 277
Click to clear both the port counters and all of the attached client's counters. The "Last Client" will not be cleared, however. : This button is available in the following modes: • Multi 802.1X • MAC-based Auth.X Click to clear only the currently selected client's counters. DOC ID: 10118801 PAGE 277 OSD2790SFP OPERATOR MANUAL...
Page 278
Indicates the rate limiter number of the ACE. The allowed range is 1 to 16. When Disabled is displayed, the rate limiter operation is disabled. Forward packet that matched the specific ACE to CPU. DOC ID: 10118801 PAGE 278 OSD2790SFP OPERATOR MANUAL...
Page 279
: The select box determines which ACL user is affected by clicking the buttons. Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately DOC ID: 10118801 PAGE 279 OSD2790SFP OPERATOR MANUAL...
Switch Port Number for which the entries are displayed. VLAN ID VLAN-ID in which the ARP traffic is permitted. MAC Address User MAC address of the entry. IP Address User IP address of the entry. DOC ID: 10118801 PAGE 280 OSD2790SFP OPERATOR MANUAL...
Page 281
: Flushes all dynamic entries : Updates the table starting from the first entry in the Dynamic ARP Inspection Table : Updates the table, starting with the entry after the last entry currently displayed DOC ID: 10118801 PAGE 281 OSD2790SFP OPERATOR MANUAL...
Switch Port Number for which the entries are displayed. VLAN ID VLAN-ID in which the IP traffic is permitted. IP Address User IP address of the entry. MAC Address Source MAC address. DOC ID: 10118801 PAGE 282 OSD2790SFP OPERATOR MANUAL...
Page 283
: Flushes all dynamic entries : Updates the table starting from the first entry in the Dynamic ARP Inspection Table : Updates the table, starting with the entry after the last entry currently displayed DOC ID: 10118801 PAGE 283 OSD2790SFP OPERATOR MANUAL...
The number of seconds left before this occurs is displayed in parentheses. This state is only reachable when more than one server is enabled. Accounting Port UDP port number for accounting. DOC ID: 10118801 PAGE 284 OSD2790SFP OPERATOR MANUAL...
Page 285
This state is only reachable when more than one server is enabled. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately DOC ID: 10118801 PAGE 285 OSD2790SFP OPERATOR MANUAL...
The statistics map closely to those specified in RFC4668 - RADIUS Authentication Client MIB. Use the server select box to switch between the backend servers to show details for. Packet Counters RADIUS authentication server packet counter. There are seven receive and four transmit counters. DOC ID: 10118801 PAGE 286 OSD2790SFP OPERATOR MANUAL...
Page 287
The number of RADIUS Access-Request packets Access radiusAuthClientExtAccessRequests sent to the server. This Requests does not include retransmissions. The number of RADIUS Access Access-Request packets radiusAuthClientExtAccessRetransmissions Retransmissions retransmitted to the RADIUS authentication DOC ID: 10118801 PAGE 287 OSD2790SFP OPERATOR MANUAL...
Page 288
This state is only reachable when more than one server is enabled. Round- The time interval (measured in milliseconds) between the Trip radiusAuthClientExtRoundTripTime most recent Access-Reply/Access-Challenge and the Time Access-Request that matched it from the RADIUS DOC ID: 10118801 PAGE 288 OSD2790SFP OPERATOR MANUAL...
Pending response. This variable is radiusAccClientExtPendingRequests Requests incremented when a Request is sent and decremented due to receipt of a Response, timeout, or retransmission. Timeouts radiusAccClientExtTimeouts The number of accounting DOC ID: 10118801 PAGE 289 OSD2790SFP OPERATOR MANUAL...
Page 290
: Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately : Clears the counters for the selected server. The “Pending Requests” counter will not be cleared by this operation DOC ID: 10118801 PAGE 290 OSD2790SFP OPERATOR MANUAL...
Page 291
Indicates the index of Statistics entry. Data Source(ifIndex) The port ID which wants to be monitored. Drop The total number of events in which packets were dropped by the probe due to lack of resources. DOC ID: 10118801 PAGE 291 OSD2790SFP OPERATOR MANUAL...
Page 292
The total number of packets (including bad packets) received that were between 256 to 511 octets in length. 512~1023 The total number of packets (including bad packets) received that were between 512 to 1023 octets in length. DOC ID: 10118801 PAGE 292 OSD2790SFP OPERATOR MANUAL...
Page 293
: Updates the table starting from the first entry in the Statistics Table, i.e. the entry with the lowest ID : Updates the table, starting with the entry after the last entry currently displayed DOC ID: 10118801 PAGE 293 OSD2790SFP OPERATOR MANUAL...
Page 294
The total number of octets of data (including those in bad packets) received on the network. Pkts The total number of packets (including bad packets, broadcast packets, and multicast packets) received. Broadcast The total number of good packets received that were directed to the broadcast address. DOC ID: 10118801 PAGE 294 OSD2790SFP OPERATOR MANUAL...
Page 295
: Updates the table starting from the first entry in the Statistics Table, i.e. the entry with the lowest ID : Updates the table, starting with the entry after the last entry currently displayed DOC ID: 10118801 PAGE 295 OSD2790SFP OPERATOR MANUAL...
Page 296
The method of sampling the selected variable and calculating the value to be compared against the thresholds. Value The value of the statistic during the last sampling period. Startup Alarm The alarm that may be sent when this entry is first set to valid. DOC ID: 10118801 PAGE 296 OSD2790SFP OPERATOR MANUAL...
Page 297
: Updates the table starting from the first entry in the Alarm Table, i.e. the entry with the lowest ID : Updates the table, starting with the entry after the last entry currently displayed DOC ID: 10118801 PAGE 297 OSD2790SFP OPERATOR MANUAL...
Page 298
The displayed fields are: Event Index Indicates the index of the event entry. Log Index Indicates the index of the log entry. LogTime Indicates Event log time LogDescription Indicates the Event description. DOC ID: 10118801 PAGE 298 OSD2790SFP OPERATOR MANUAL...
Page 299
: Updates the table starting from the first entry in the Event Table, i.e. the entry with the lowest ID : Updates the table, starting with the entry after the last entry currently displayed DOC ID: 10118801 PAGE 299 OSD2790SFP OPERATOR MANUAL...
Aggregated ports Aggregated member ports of the Aggregation group. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately DOC ID: 10118801 PAGE 300 OSD2790SFP OPERATOR MANUAL...
Page 301
Shows which ports are a part of this aggregation for this switch. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately DOC ID: 10118801 PAGE 301 OSD2790SFP OPERATOR MANUAL...
Page 302
The Aggregation ID assigned to this aggregation group. Partner System ID The partner's System ID (MAC address). Partner Port The partner's port number connected to this port. Partner Prio The partner's port priority. DOC ID: 10118801 PAGE 302 OSD2790SFP OPERATOR MANUAL...
Page 303
OPTICAL SYSTEMS DESIGN Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately DOC ID: 10118801 PAGE 303 OSD2790SFP OPERATOR MANUAL...
Page 304
: Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately : Clears the counters for the selected server. The “Pending Requests” counter will not be cleared by this operation DOC ID: 10118801 PAGE 304 OSD2790SFP OPERATOR MANUAL...
The time of the last loop event detected. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately DOC ID: 10118801 PAGE 305 OSD2790SFP OPERATOR MANUAL...
Topology Change Last The time since last Topology Change occurred. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately DOC ID: 10118801 PAGE 306 OSD2790SFP OPERATOR MANUAL...
Page 307
The time since the bridge port was last initialized. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately DOC ID: 10118801 PAGE 307 OSD2790SFP OPERATOR MANUAL...
Page 308
The number of illegal Spanning Tree BPDU's received (and discarded) on the port. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately DOC ID: 10118801 PAGE 308 OSD2790SFP OPERATOR MANUAL...
The number of Received IGMPv2 Leave's and MLDv1 Done's, respectively. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately : Clears all Ststistics counters DOC ID: 10118801 PAGE 309 OSD2790SFP OPERATOR MANUAL...
"No more entries" is shown in the displayed table. Use the button to start over. MVR CHANNELS (GROUPS) INFORMATION TABLE COLUMNS VLAN ID VLAN ID of the group. Groups Group ID of the group displayed. Port Members Ports under this group. DOC ID: 10118801 PAGE 310 OSD2790SFP OPERATOR MANUAL...
Page 311
: Refreshes the displayed table starting from the input fields : Updates the table starting from the first entry in the MVR Channels (Groups) Information Table : Updates the table, starting with the entry after the last entry currently displayed DOC ID: 10118801 PAGE 311 OSD2790SFP OPERATOR MANUAL...
Group Group address of the group displayed. Port Switch port number. Mode Indicates the filtering mode maintained per (VLAN ID, port number, Group Address) basis. It can be either Include or Exclude. DOC ID: 10118801 PAGE 312 OSD2790SFP OPERATOR MANUAL...
Page 313
: Refreshes the displayed table starting from the input fields : Updates the table starting from the first entry in the MVR Channels (Groups) Information Table : Updates the table, starting with the entry after the last entry currently displayed DOC ID: 10118801 PAGE 313 OSD2790SFP OPERATOR MANUAL...
OPTICAL SYSTEMS DESIGN IPMC IGMP SNOOPING IGMP Snooping Status Monitor IPMC IGMP Snooping Status This page provides IGMP Snooping status. VLAN ID The VLAN ID of the entry. Querier Version Working Querier Version currently. DOC ID: 10118801 PAGE 314 OSD2790SFP OPERATOR MANUAL...
Page 315
Indicate whether specific port is a router port or not. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately : Clears all Statistics counters DOC ID: 10118801 PAGE 315 OSD2790SFP OPERATOR MANUAL...
"No more entries" is shown in the displayed table. Use the button to start over. IGMP GROUP TABLE COLUMNS VLAN ID VLAN ID of the group. Groups Group address of the group displayed. Port Members Ports under this group. DOC ID: 10118801 PAGE 316 OSD2790SFP OPERATOR MANUAL...
Page 317
: Refreshes the displayed table starting from the input fields : Updates the table starting from the first entry in the MVR Channels (Groups) Information Table : Updates the table, starting with the entry after the last entry currently displayed DOC ID: 10118801 PAGE 317 OSD2790SFP OPERATOR MANUAL...
Group Group address of the group displayed. Port Switch port number. Mode Indicates the filtering mode maintained per (VLAN ID, port number, Group Address) basis. It can be either Include or Exclude. DOC ID: 10118801 PAGE 318 OSD2790SFP OPERATOR MANUAL...
Page 319
: Refreshes the displayed table starting from the input fields : Updates the table starting from the first entry in the IGMP SFM Information Table : Updates the table, starting with the entry after the last entry currently displayed DOC ID: 10118801 PAGE 319 OSD2790SFP OPERATOR MANUAL...
Page 320
Querier Status Shows the Querier status is "ACTIVE" or "IDLE". "DISABLE" denotes the specific interface is administratively disabled. Queries Transmitted The number of Transmitted Queries. Queries Received The number of Received Queries. DOC ID: 10118801 PAGE 320 OSD2790SFP OPERATOR MANUAL...
Page 321
Indicate whether specific port is a router port or not. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately : Clears all Statistics counters DOC ID: 10118801 PAGE 321 OSD2790SFP OPERATOR MANUAL...
: Refreshes the displayed table starting from the input fields : Updates the table starting from the first entry in the MLD Group Table : Updates the table, starting with the entry after the last entry currently displayed DOC ID: 10118801 PAGE 322 OSD2790SFP OPERATOR MANUAL...
Group Group address of the group displayed. Port Switch port number. Mode Indicates the filtering mode maintained per (VLAN ID, port number, Group Address) basis. It can be either Include or Exclude. DOC ID: 10118801 PAGE 323 OSD2790SFP OPERATOR MANUAL...
Page 324
: Refreshes the displayed table starting from the input fields : Updates the table starting from the first entry in the MLD SFM Table : Updates the table, starting with the entry after the last entry currently displayed DOC ID: 10118801 PAGE 324 OSD2790SFP OPERATOR MANUAL...
System Name The name advertised by the neighbor unit. System Capabilities Describes the neighbour unit's capabilities. The possible capabilities are: 1. Other 2. Repeater 3. Bridge 4. WLAN Access Point 5. Router DOC ID: 10118801 PAGE 325 OSD2790SFP OPERATOR MANUAL...
Page 326
This could for instance hold the neighbor's IP address. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh this page DOC ID: 10118801 PAGE 326 OSD2790SFP OPERATOR MANUAL...
Page 327
Generic Endpoints (Class I), and any LLDP-MED Endpoint Device claiming compliance as a Communication Device (Class III) will also support all aspects of TIA-1057 applicable to both Media Endpoints (Class II) and Generic Endpoints (Class I). DOC ID: 10118801 PAGE 327 OSD2790SFP OPERATOR MANUAL...
Page 328
LLDP-MED Capabilities describes the neighbour unit's LLDP-MED capabilities. The possible capabilities are: 1. LLDP-MED capabilities 2. Network Policy 3. Location Identification 4. Extended Power via MDI - PSE 5. Extended Power via MDI - PD 6. Inventory 7. Reserved DOC ID: 10118801 PAGE 328 OSD2790SFP OPERATOR MANUAL...
Page 329
Untagged: The device is using an untagged frame format and as such does not include a tag header as defined by IEEE 802.1Q-2003. Tagged: The device is using the IEEE 802.1Q tagged frame format. DOC ID: 10118801 PAGE 329 OSD2790SFP OPERATOR MANUAL...
Page 330
MAU type field value rather than by auto-negotiation. Auto-negotiation Capabilities Shows the link partners MAC/PHY capabilities. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh this page DOC ID: 10118801 PAGE 330 OSD2790SFP OPERATOR MANUAL...
Systems that do not implement this option default the value to be the same as that of the Receive Tw_sys_tx. DOC ID: 10118801 PAGE 331 OSD2790SFP OPERATOR MANUAL...
Page 332
Green - Switch and link partner have agreed on wakeup times. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh this page DOC ID: 10118801 PAGE 332 OSD2790SFP OPERATOR MANUAL...
Total Neighbors Entries Dropped Shows the number of LLDP frames dropped due to the entry table being full. Total Neighbors Entries Aged Out Shows the number of entries deleted due to Time-To-Live expiring. DOC ID: 10118801 PAGE 333 OSD2790SFP OPERATOR MANUAL...
If checked the counters for the specific interface are cleared when is pressed. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately : Clears all Statistics counters DOC ID: 10118801 PAGE 334 OSD2790SFP OPERATOR MANUAL...
4. LTC phase : Local Time Counter (LTC) phase control (assumes that the frequency is locked by means of SyncE) Clock Frequency Shows the current clock frequency used by the External Clock. The possible range of values are 1 - 25000000 (1 - 25MHz) DOC ID: 10118801 PAGE 335 OSD2790SFP OPERATOR MANUAL...
Shows the ports configured for that Clock Instance. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately DOC ID: 10118801 PAGE 336 OSD2790SFP OPERATOR MANUAL...
Monitor MAC Table Entries in the MAC Table are shown on this page. The MAC Table contains up to 8192 entries, and is sorted first by VLAN ID, then by MAC address. DOC ID: 10118801 PAGE 337 OSD2790SFP OPERATOR MANUAL...
: Updates the table starting from the first entry in the MAC Table, i.e. the entry with the lowest VLAN ID and MAC address : Updates the table, starting with the entry after the last entry currently displayed DOC ID: 10118801 PAGE 338 OSD2790SFP OPERATOR MANUAL...
The "VLAN" input field allows the user to select the starting point in the VLAN Table. Clicking the button will update the displayed table starting from that or the closest next VLAN Table match. DOC ID: 10118801 PAGE 339 OSD2790SFP OPERATOR MANUAL...
Page 340
: Select VLAN Users from this drop down list. Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately DOC ID: 10118801 PAGE 340 OSD2790SFP OPERATOR MANUAL...
Page 341
The field is empty if not overridden by the selected user. Frame Type Shows the acceptable frame types (All, Taged, Untagged) that a given user wants to configure on the port. The field is empty if not overridden by the selected user. DOC ID: 10118801 PAGE 341 OSD2790SFP OPERATOR MANUAL...
Page 342
: Select VLAN Users from this drop down list. Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately DOC ID: 10118801 PAGE 342 OSD2790SFP OPERATOR MANUAL...
• If sFlow is currently configured through Web or CLI, Owner contains <Configured through local management>. • If sFlow is currently configured through SNMP, Owner contains a string identifying the sFlow receiver. DOC ID: 10118801 PAGE 343 OSD2790SFP OPERATOR MANUAL...
The ID of Device. Device Name(local) Name of the Device. Bidirectional State The current state of the port. NEIGHBOUR STATUS Port The current port of neighbor device. Device ID The current ID of neighbor device. DOC ID: 10118801 PAGE 345 OSD2790SFP OPERATOR MANUAL...
Page 346
: The port select box determines which port is affected by clicking the buttons. Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately DOC ID: 10118801 PAGE 346 OSD2790SFP OPERATOR MANUAL...
Temperature setting for the alarm to trigger. Enable Shows if the alarm is Enabled/Disabled. Current Temperature Current temperature of the board. Active Shows the temperature alarm status. Alarm Time Time when the temperature alarm triggered. DOC ID: 10118801 PAGE 348 OSD2790SFP OPERATOR MANUAL...
Page 349
OPTICAL SYSTEMS DESIGN Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Refreshes the page : Clear the Alarm selected DOC ID: 10118801 PAGE 349 OSD2790SFP OPERATOR MANUAL...
Click on to retrieve another content of interest. Buttons : Click to start transmitting ICMP packets : Click to re-start diagnostics with PING : Retrieves content of interest DOC ID: 10118801 PAGE 351 OSD2790SFP OPERATOR MANUAL...
Ping Length The payload size of the ICMP packet. Values range from 2 bytes to 1452 bytes. Ping Count The count of the ICMP packet. Values range from 1 time to 60 times. DOC ID: 10118801 PAGE 352 OSD2790SFP OPERATOR MANUAL...
Page 353
Do not specify egress interface for loopback address. Do specify egress interface for link-local or multicast address. Buttons : Click to start transmitting ICMPv6 packets : Click to re-start diagnostics with PING : Retrieves content of interest DOC ID: 10118801 PAGE 353 OSD2790SFP OPERATOR MANUAL...
You can restart the switch on this page. After restart, the switch will boot normally. Buttons : Click to restart device. : Click to return to the Port State page without restarting. DOC ID: 10118801 PAGE 354 OSD2790SFP OPERATOR MANUAL...
2 within the first minute from switch reboot. In the first minute after boot, 'loopback' packets will be transmitted at port 1. If a 'loopback' packet is received at port 2 the switch will do a restore to default DOC ID: 10118801 PAGE 355 OSD2790SFP OPERATOR MANUAL...
Do not restart or power off the device at this time or the switch may fail to function afterwards. Buttons : Click to locate file for uploading. : Click to start upload process. DOC ID: 10118801 PAGE 356 OSD2790SFP OPERATOR MANUAL...
The date where the firmware was produced. Buttons : Click to use the alternate image. This button may be disabled depending on system state. : Cancel activating the backup image. Navigates away from this page. DOC ID: 10118801 PAGE 357 OSD2790SFP OPERATOR MANUAL...
Up to 31 other files, typically used for configuration backups or alternative configurations. Save startup-config This copies running-config to startup-config, thereby ensuring that the currently active configuration will be used at the next reboot. Buttons : Click to save the current configuration. DOC ID: 10118801 PAGE 358 OSD2790SFP OPERATOR MANUAL...
Page 359
It is possible to download any of the files on the switch to the web browser. Select the file and click Download of running-config may take a little while to complete, as the file must be prepared for download. Buttons : Click to download the configuration. DOC ID: 10118801 PAGE 359 OSD2790SFP OPERATOR MANUAL...
Page 360
Instead an existing file must be overwritten or another file must be deleted. Buttons : Click to locate file for uploading. : Click to start upload process. DOC ID: 10118801 PAGE 360 OSD2790SFP OPERATOR MANUAL...
Page 361
Select the file to activate and click . This will initiate the process of completely replacing the existing configuration with that of the selected file. Buttons : Click to activate configuration file. DOC ID: 10118801 PAGE 361 OSD2790SFP OPERATOR MANUAL...
Page 362
It is possible to delete any of the writable files stored in flash, including startup-config. If this is done and the switch is rebooted without a prior Save operation, this effectively resets the switch to default configuration. Buttons : Click to delete configuration file. DOC ID: 10118801 PAGE 362 OSD2790SFP OPERATOR MANUAL...
For warranty period, please call your local OSD distributor. REPAIRS Optical Systems Design reserves the right to repair or replace faulty modules/units. Please obtain a “Return Material Authorisation” (RMA) form and number before returning goods. Goods must be returned in adequate packing material to Optical Systems Design, Warriewood or its nominated authorised representative, for all repairs.