YASKAWA CIPR-GA70C Series Initial Steps page 28

12 Drive Control, Duty Modes, and Programming
No.
Name
(Hex.)
E2-11 Motor Rated Power (kW) Sets the motor rated power in 0.01 kW units. (1 HP = 0.746 kW)
(0318)
H1-01 to H1-08 Terminal Sx Function
Selection
(0438, 0439,
0400 - 0405)
H2-01 Term M1-M2 Function
Selection
(040B)
H2-02 Term M3-M4 Function
Selection
(040C)
H3-01 Terminal A1 Signal Level
Select
(0410)
H3-02 Terminal A1 Function
Selection
(0434)
H3-03 Terminal A1 Gain Setting Sets the gain of the analog signal input to MFAI terminal A1.
(0411)
RUN
H3-04 Terminal A1 Bias Setting Sets the bias of the analog signal input to MFAI terminal A1.
(0412)
RUN
H3-05 Terminal A3 Signal Level
Select
(0413)
H3-06 Terminal A3 Function
Selection
(0414)
H3-07 Terminal A3 Gain Setting Sets the gain of the analog signal input to MFAI terminal A3.
(0415)
RUN
H3-08 Terminal A3 Bias Setting Sets the bias of the analog signal input to MFAI terminal A3.
(0416)
RUN
H3-09 Terminal A2 Signal Level
Select
(0417)
H3-10 Terminal A2 Function
Selection
(0418)
H3-11 Terminal A2 Gain Setting Sets the gain of the analog signal input to MFAI terminal A2.
(0419)
RUN
H3-12 Terminal A2 Bias Setting Sets the bias of the analog signal input to MFAI terminal A2.
(041A)
RUN
H3-13 Analog Input FilterTime
Constant
(041B)
H3-14 Analog Input Terminal
Enable Sel
(041C)
H4-01 Terminal FM Analog
Output Select
(041D)
H4-02 Terminal FM Analog
Output Gain
(041E)
RUN
EN 28
Sets the functions for MFDI terminals S1 to S8.
Sets the function for MFDO terminal M1-M2.
Sets the function for MFDO terminal M3-M4.
Sets the input signal level for MFAI terminal A1.
0: 0 to 10V (Lower Limit at 0), 1: -10 to +10V (Bipolar Reference), 2: 4 to 20 mA,
3: 0 to 20 mA
Sets the function for MFAI terminal A1.
Sets the input signal level for MFAI terminal A3.
0: 0 to 10V (Lower Limit at 0), 1: -10 to +10V (Bipolar Reference), 2: 4 to 20 mA,
3: 0 to 20 mA
Sets the function for MFAI terminal A3.
Sets the input signal level for MFAI terminal A2.
0: 0 to 10V (Lower Limit at 0), 1: -10 to +10V (Bipolar Reference), 2: 4 to 20 mA,
3: 0 to 20 mA
Sets the function for MFAI terminal A2.
Sets the time constant for primary delay filters on MFAI terminals.
Sets which Sx terminal is enabled when H1-xx = C [MFDI Function Select = Analog
Terminal Enable Selection] is ON.
1: Terminal A1 only, 2: Terminal A2 only, 3: Terminals A1 and A2, 4: Terminal A3 only,
5: Terminals A1 and A3, 6: Terminals A2 and A3, 7: Terminals A1, A2, and A3
Sets which drive monitor Ux-xx to output from MFAO terminal FM.
Sets the gain of the Ux-xx monitor signal in H4-01 [Terminal FM Analog Output Select].
YASKAWA ELECTRIC TOEP C710617 17D YASKAWA AC Drive GA700 Initial Steps
Description