Danfoss VLT Programming Manual page 62

Parameter Description
[14] Above The motor current is higher than set in
current, high 4-51 Warning Current High.
[15] Out of speed The output speed is outside the range set in
range 4-52 Warning Speed Low and 4-53 Warning
Speed High.
[16] Below speed, The output speed is lower than the setting
low in 4-52 Warning Speed Low.
[17] Above speed, The output speed is higher than the setting
high in 4-53 Warning Speed High.
[18] Out of The feedback is outside the range set in
feedback 4-56 Warning Feedback Low and
range 4-57 Warning Feedback High.
[19] Below The feedback is below the limit set in
feedback low 4-56 Warning Feedback Low.
[20] Above The feedback is above the limit set in
feedback high 4-57 Warning Feedback High.
[21] Thermal The thermal warning turns on when the
warning temperature exceeds the limit in the motor,
the frequency converter, the brake resistor,
or the thermistor.
[25] Reverse Reversing. Logic '1' = relay activated, 24 V DC
when CW rotation of the motor. Logic '0' =
relay not activated, no signal, when CCW
rotation of the motor.
[26] Bus OK Active communication (no time-out) via the
serial communication port.
[27] Torque limit Use in performing a coasting stop and in
and stop torque limit condition. If the frequency
converter has received a stop signal and is at
the torque limit, the signal is Logic '0'.
[28] Brake, no The brake is active and there are no
warning warnings.
[29] Brake ready, The brake is ready for operation and there
no fault are no faults.
[30] Brake fault The output is Logic '1' when the brake IGBT
(IGBT) is short-circuited. Use this function to
protect the frequency converter if there is a
fault on the brake modules. Use the output/
relay to cut out the main voltage from the
frequency converter.
[35] External External Interlock function has been
Interlock activated via one of the digital inputs.
[40] Out of ref
range
[41] Below
reference low
[42] Above
reference
high
[45] Bus Ctrl
[46] Bus Ctrl 1 if
timeout
[47] Bus Ctrl 0 if
timeout
[55] Pulse output
®
VLT HVAC Drive Programming Guide
[60]
[61]
[62]
[63]
[64]
[65]
[70]
[71]
[72]
[73]
[74]
[75]
[80]
[81]
[82]
[83]
®
MG.11.CB.02 - VLT is a registered Danfoss trademark
Comparator 0 See parameter group 13-1*. If Comparator 0
is evaluated as TRUE, the output will go
high. Otherwise, it will be low.
Comparator 1 See parameter group 13-1*. If Comparator 2
is evaluated as TRUE, the output will go
high. Otherwise, it will be low.
Comparator 2 See parameter group 13-1*. If Comparator 2
is evaluated as TRUE, the output will go
high. Otherwise, it will be low.
Comparator 3 See parameter group 13-1*. If Comparator 3
is evaluated as TRUE, the output will go
high. Otherwise, it will be low.
Comparator 4 See parameter group 13-1*. If Comparator 4
is evaluated as TRUE, the output will go
high. Otherwise, it will be low.
Comparator 5 See parameter group 13-1*. If Comparator 5
is evaluated as TRUE, the output will go
high. Otherwise, it will be low.
Logic Rule 0 See parameter group 13-4*. If Logic Rule 0 is
evaluated as TRUE, the output will go high.
Otherwise, it will be low.
Logic Rule 1 See parameter group 13-4*. If Logic Rule 1 is
evaluated as TRUE, the output will go high.
Otherwise, it will be low.
Logic Rule 2 See parameter group 13-4*. If Logic Rule 2 is
evaluated as TRUE, the output will go high.
Otherwise, it will be low.
Logic Rule 3 See parameter group 13-4*. If Logic Rule 3 is
evaluated as TRUE, the output will go high.
Otherwise, it will be low.
Logic Rule 4 See parameter group 13-4*. If Logic Rule 4 is
evaluated as TRUE, the output will go high.
Otherwise, it will be low.
Logic Rule 5 See parameter group 13-4*. If Logic Rule 5 is
evaluated as TRUE, the output will go high.
Otherwise, it will be low.
SL Digital See 13-52 SL Controller Action. The input will
Output A go high whenever the Smart Logic Action
[38] Set dig. out. A high is executed. The input
will go low whenever the Smart Logic Action
[32] Set dig. out. A low is executed.
SL Digital See 13-52 SL Controller Action. The input will
Output B go high whenever the Smart Logic Action
[39] Set dig. out. Bhigh is executed. The input
will go low whenever the Smart Logic Action
[33] Set dig. out. B low is executed.
SL Digital See 13-52 SL Controller Action. The input will
Output C go high whenever the Smart Logic Action
[40] Set dig. out. C high is executed. The input
will go low whenever the Smart Logic Action
[34] Set dig. out. C low is executed.
SL Digital See 13-52 SL Controller Action. The input will
Output D go high whenever the Smart Logic Action
[41] Set dig. out. D high is executed. The
input will go low whenever the Smart Logic
Action [35] Set dig. out. D low is executed.
3 3
61