Directed DS3 Installation Manual
Hide thumbs
Also See for DS3:
- Installation manual (27 pages) ,
- Installation manual (24 pages) ,
- Installation manual (35 pages)
Table of Contents
Advertisement
Quick Links
INSTALLATION GUIDE
DS3+ / DS4+
2010 Chrysler Sebring Convertible. 933.CHRYSLER 7.34.195.3
Designed by Installers for Installers
© 2022 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle's
electrical system and components.
Advertisement
Table of Contents
Related Manuals for Directed DS3
Summary of Contents for Directed DS3
- Page 1 2010 Chrysler Sebring Convertible. 933.CHRYSLER 7.34.195.3 Designed by Installers for Installers © 2022 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s...
-
Page 2: Table Of Contents
Contents Introduction Vehicle function compatibilities Pre-installation and application warnings Installation Wiring diagram with T-Harness (THCHN2) Wiring diagram Locating components in the vehicle Vehicle connections Module programming Key-Type vehicles Push-to-Start (PTS) vehicles Module programming for security-only installations Pairing remotes Connecting the module 8556T Temperature Sensor 8504D Combo Sensor RF Systems... -
Page 3: Introduction
Introduction This guide provides information on the installation of the DS3/DS3+ and DS4/DS4+ modules as a digital solution. Using these modules in a digital configuration require the module to be flashed with vehicle specific firmware. Refer to our website (www.directechs.com) and click on the DIRECTLINK text in the header for additional information. -
Page 4: Vehicle Function Compatibilities
Vehicle function compatibilities This section lists all the functions compatible with this vehicle for the installation illustrated in this guide. Note: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart. Parking Lights Control RAP Shut Down (Retained ACC Power) Arm Factory Security Remote Start Takeover Disarm Factory Security... -
Page 5: Pre-Installation And Application Warnings
Pre-installation and application warnings Firmware notes: This section highlights important information for this specific firmware and will assist in pricing accordingly, as well as bringing awareness to any operational or vehicle limitations. T-Harness THCHN2 Keys required for Keys required for compatible programming operation... -
Page 6: Installation
Wiring diagram with T-Harness (THCHN2) Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( Sentry Key Module (black 8-pin conn.) To vehicle male 8-pin connector at the ignition switch To 8-pin Female Connector at the ignition switch HS CAN High: Orange/Green... -
Page 7: Wiring Diagram
Wiring diagram Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( (MUX) Ignition: Violet/Brown, pin 1 CAN C High: Green or White/ Lt. Blue, pin 6 (+) Ignition: Pink or Pink/White, pin 3 Diagnostic Connector OBDII (connector side view) -
Page 8: Locating Components In The Vehicle
Locating components in the vehicle Optional starter disable connection When using an external relay, use a 1N4002 diode or larger. 1A diode [1N4002+] (+) Ignition (-) Ground When Armed (GWA) Output: Red/White: 4 Refer to the Vehicle connections section for wire and Starter (conn. -
Page 9: Vehicle Connections
Vehicle connections The connection information listed below is specific to the 2010 Chrysler Sebring Convertible. Refer to “Pre-installation and application warnings” for a list of important notes. Data harness, 8-pin white connector (H1) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Connection... - Page 10 Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Connection H2/16 Red/Blue (-) Headlight Detection Input No Connection H2/17 Black/White (-) E-Brake Input No Connection H2/18 Orange/Black (+) Instant Alarm Input No Connection H2/19 Blue (-) Trunk Input No Connection H2/20 Green...
- Page 11 Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Connection H4/10 Pink (+) Ignition Input/Output No Connection RF Port harness, 2-pin white connector (H5) Module Conn./Pin Color Description H5/1 RF Loop H5/2 RF Loop D2D harness, 4-pin white (1) and black (2) connectors (H6) Module Conn./Pin Color...
-
Page 12: Module Programming
Connect the 12-pin main power harness to the module. DS3+: Wait until the LED turns on solid red then proceed to the next step. DS4+: The LED turns ON solid blue for 1 second to confirm Bluetooth communication. Wait until the LED turns ON solid red, then proceed to the next step. - Page 13 933.CHRYSLER 7.34.195.3 2010 Chrysler Sebring Convertible ©2022 VOXX•DEI LLC. All rights reserved.
-
Page 14: Push-To-Start (Pts) Vehicles
Connect the 12-pin main power harness to the module. DS3+: Wait until the LED turns on solid red then proceed to the next step. DS4+: The LED turns ON solid blue for 1 second to confirm Bluetooth communication. Wait until the LED turns ON solid red, then proceed to the next step. - Page 15 www.directechs.com. You have successfully completed the module programming sequence. 933.CHRYSLER 7.34.195.3 2010 Chrysler Sebring Convertible ©2022 VOXX•DEI LLC. All rights reserved.
-
Page 16: Module Programming For Security-Only Installations
For vehicles equipped with a manual transmission, make sure the gearshift lever is in the neutral position. Must connect 12-pin FIRST DS3+: Connect the 12-pin main power harness to the DS3+ module FIRST. DS3/DS3+ Wait until the LED turns ON solid orange before proceeding to the next step. Solid DS4+: Connect the 12-pin main power harness to the DS4+ module FIRST. -
Page 17: Pairing Remotes
Note: Connected devices become registered within 4 to 6 seconds. 8556T Temperature Sensor The 8556T Temperature Sensor is optional, but included with your DS3+/DS4+ module. When used, the Temperature Sensor must be plugged into the 2-pin black connector of your module. -
Page 18: When Used In Conjunction With Smartstart
Loops Pigtails DO NOT connect the Directed SmartStart ® 2-pin power harness when using the DS3+/DS4+. Power and ground will be provided by the D2D connector on the module. Refer to the Directed SmartStart ® documentation for further details. D2D port configuration Caution! Do not connect the Control Center (antenna) or any digital sensors (8504D) to the white D2D1 port. -
Page 19: Manual Transmission
Manual Transmission IMPORTANT! Directed does not approve nor support installations of manual transmission and remote starts on any electronic vehicles (EV), OEM Remote Start Activation firmware, vehicles with convertibles and/or removable tops, including but not limited to Jeep Wrangler, Honda S2000, Mazda Miata, and other such vehicles. -
Page 20: Led Diagnostics And Troubleshooting
LED diagnostics and troubleshooting This section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation. Module Programming Description Troubleshooting Make sure the D2D harness is connected and that 12 Volt is present between the red and black wires. If Module has no power. - Page 21 External Module Synchronization Description Troubleshooting OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. (Flashes red, red, then orange) x 10 Active Ground When Running (Status) Description Troubleshooting Ground When Running (Status) command The module has initialized the remote start sequence.
-
Page 22: Soft Reset
If required for your installation, connect all the harnesses to the module, EXCEPT the 12-pin main 12-pin harness power harness. Press and hold the programming button, then connect the 12-pin harness to the module. DS3+: Wait 3 seconds until the LED turns ON solid orange then release the programming button. & &... -
Page 23: Tach Learning Procedure (Not Needed With Virtual Tach)
Tach learning procedure (not needed with Virtual Tach) Data Tach: The procedure is not required as the tach comes preprogrammed. However, it is strongly recommended to learn the exact value of the vehicle for the most consistent and reliable starting and functionality. Hardwired Tach: The procedure is required. -
Page 24: Limited Lifetime Consumer Warranty
Limited Lifetime Consumer Warranty VOXX DEI LLC (the Company) warrants to the original purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or work- manship within the Lifetime from the date of original purchase in the original vehicle, such defect(s) will be repaired or replaced with new or reconditioned product, (at the Company’s option) without charge for parts or repair labor. -
Page 25: Quick Reference Guide
Aftermarket remote. Send the Unlock command on the factory or Press Unlock on • Directed SmartStart application via your smartphone. either remote* aftermarket remote.* If applicable, you can also start the engine remotely by pressing the Lock button 3 Complete the following steps within 45 seconds or the vehicle will shut down. - Page 26 * Press & hold for 5 seconds to activate the trunk release (optional). * Icon and remote appearance may differ depending on the model purchased. SmartStart Bluetooth compatibility (applicable to DS4/DS4+ ONLY) This system is compatible with Directed SmartStart. For a complete list of supported features, please visit www.mysmartstart.com. What is SmartStart? Now you can remote start, lock and unlock your car just by pushing a button on your smartphone;...