Directed DS4+ Installation Manual
  1. Manuals
  2. Brands
  3. Directed Manuals
  4. Automobile Electronics
  5. DS4+
  6. Installation manual
Directed DS4+ Installation Manual

Directed DS4+ Installation Manual

2010 mercury mariner. 933.ford6 3.20.193
Hide thumbs Also See for DS4+:
Table of Contents

Advertisement

Quick Links

See also: Installation Manual
INSTALLATION GUIDE
DS4+
2010 Mercury Mariner. 933.FORD6 3.20.193
Designed by Installers for Installers
© 2019 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle's
electrical system and components.

Advertisement

Table of Contents
loading

Related Manuals for Directed DS4+

Summary of Contents for Directed DS4+

  • Page 1 2010 Mercury Mariner. 933.FORD6 3.20.193 Designed by Installers for Installers © 2019 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s...

  • Page 2: Table Of Contents

    Contents Introduction Vehicle function compatibilities Pre-installation and application warnings Installation Wiring diagram with T-Harness (THFON1) Wiring diagram Locating components in the vehicle Key2Go Optional starter disable connection Vehicle connections Connecting the module Important! RF Systems 8556T Temperature Sensor 8504D Combo Sensor When used in conjunction with SmartStart D2D port configuration Module programming...
  • Page 3 The following safety warnings must be observed at all times: • Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. • When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation.

  • Page 4: Introduction

    Factory Alarm Trigger Monitoring Key2GO Brake Status (foot brake) Immobilizer Bypass-Data No Key Req'd Door Locks Status Accessory Activation E-Brake Status Ignition Activation Ignition Status RAP Shut Down (Retained ACC Power) 933.FORD6 3.20.193 2010 Mercury Mariner © 2019-01-18 Directed. All rights reserved.

  • Page 5: Pre-Installation And Application Warnings

    For Security Only installations, refer to the "Locating components in the vehicle" section for the optional starter disable connection. This connection is NOT required when using the THFON1 T-Harness. 933.FORD6 3.20.193 2010 Mercury Mariner © 2019-01-18 Directed. All rights reserved.
  • Page 6 (AC) Tach Input: Violet/White male female (+) Siren Output: Brown/Red Siren Slide OBDII Diagnostic DS4+ to open Legend: Mandatory Connections Security Only Remote Start Only Remote Start + Security 933.FORD6 3.20.193 2010 Mercury Mariner © 2019-01-18 Directed. All rights reserved.

  • Page 7: Wiring Diagram

    RAP Off Interrupt (connector side): Lt. Green: 8 RAP Off Interrupt (vehicle side): Lt. Green/White: 9 (-) Ground: Black: 10 Slide DS4+ to open Legend: Mandatory Connections Security Only Remote Start Only Remote Start + Security 933.FORD6 3.20.193 2010 Mercury Mariner © 2019-01-18 Directed. All rights reserved.

  • Page 8: Locating Components In The Vehicle

    Locating components in the vehicle 933.FORD6 3.20.193 2010 Mercury Mariner © 2019-01-18 Directed. All rights reserved.

  • Page 9: Key2Go

    Any first-time user must re-register to gain access to Key2GO, and some additional information will be required to complete the registration process, such as your Directed account number and store name. Key2GO is compatible with XKLoader2 and the online web tool, as well as XKLoader3 and the Directechs Mobile application.

  • Page 10: Optional Starter Disable Connection

    (-) Starter Output: Violet/Black: 8 Vehicle connections section for wire and connector Starter (connector side) details. Starter (vehicle side) Legend: Mandatory Connections Security Only Remote Start Only Remote Start + Security 933.FORD6 3.20.193 2010 Mercury Mariner © 2019-01-18 Directed. All rights reserved.

  • Page 11: Vehicle Connections

    Brown/Red (+) Siren Output [2] Security Only H2/12 Pink (+) Ignition Sense Input No Connection H2/13 Violet (+) Door Input No Connection H2/14 Brown (+) Brake Input No Connection 933.FORD6 3.20.193 2010 Mercury Mariner © 2019-01-18 Directed. All rights reserved.
  • Page 12 (+) 12 Volt Input No Connection H4/3 Pink/Black Starter Input (Key Side) No Connection H4/4 Pink/White (+) Flex Relay Output No Connection H4/5 (+) 12 Volt Input No Connection 933.FORD6 3.20.193 2010 Mercury Mariner © 2019-01-18 Directed. All rights reserved.
  • Page 13 (+) 12 Volt Temperature sensor harness, 2-pin black connector (H7) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Connection H7/1 Black Temperature Sensor H7/2 Black Temperature Sensor 933.FORD6 3.20.193 2010 Mercury Mariner © 2019-01-18 Directed. All rights reserved.

  • Page 14: Connecting The Module

    To enable D2D communication between the DS4+ and the SmartStart one of the following actions must be executed: SmartStart with Loops – The brown loop must be cut. • SmartStart with Pigtails – The gray wire must be connected to a ground source. • Loops Pigtails 933.FORD6 3.20.193 2010 Mercury Mariner © 2019-01-18 Directed. All rights reserved.

  • Page 15: When Used In Conjunction With Smartstart

    SmartStart. To ensure proper functionality with SmartStart, it is important that it is selected in the system programming of the DirectLink application or via the online web tool. Note: Both black D2D ports are reserved for the Control Center (antenna) and 8504D Combo Sensor. 933.FORD6 3.20.193 2010 Mercury Mariner © 2019-01-18 Directed. All rights reserved.

  • Page 16: Module Programming

    "Initialize Virtual Tach (not needed with hardwired or data tach applications". * Your aftermarket remote may differ from the model shown in the illustrations. You have successfully completed the module programming sequence. 933.FORD6 3.20.193 2010 Mercury Mariner © 2019-01-18 Directed. All rights reserved.

  • Page 17: 1-Key Programming Using Key2Go

    "Initialize Virtual Tach (not needed with hardwired or data tach applications". * Your aftermarket remote may differ from the model shown in the illustrations. You have successfully completed the module programming sequence. 933.FORD6 3.20.193 2010 Mercury Mariner © 2019-01-18 Directed. All rights reserved.

  • Page 18: Led Diagnostics And Troubleshooting

    The Violet/Green or Violet/Brown wire did not detect the expected voltage value. Refer to MUX not detected. “Installation (wiring diagrams & vehicle wiring reference charts)” to check the connections. Flashes red x 7 933.FORD6 3.20.193 2010 Mercury Mariner © 2019-01-18 Directed. All rights reserved.
  • Page 19 The smart key was not detected, which prevents the system from shutting down the vehicle. Flashes red x 3 Speed was detected. The vehicle was detected as moving, which prevents the system from shutting it down. Flashes red x 4 933.FORD6 3.20.193 2010 Mercury Mariner © 2019-01-18 Directed. All rights reserved.

  • Page 20: Soft Reset

    After 3 seconds the LED turns ON solid orange. Keep holding the programming button until & & the LED flashes red, then orange slowly. Solid Flashes Hold Release the programming button. The LED turns ON solid red. & Solid Release 933.FORD6 3.20.193 2010 Mercury Mariner © 2019-01-18 Directed. All rights reserved.

  • Page 21: Learning The Tach (Not Needed With Virtual Tach)

    Important! After successfully learning Virtual Tach, a small minority of vehicle starters may over crank or under crank during remote start. Use the VirtualTach Fine tune feature in the configuration wizard to adjust the starter output time in 50mS increments to compensate for such an occurrence. 933.FORD6 3.20.193 2010 Mercury Mariner © 2019-01-18 Directed. All rights reserved.

  • Page 22: Limited Lifetime Consumer Warranty

    Directed dealer, the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer’s name, telephone number and address;...

  • Page 23: Quick Reference Guide

    Factory remote. Press the Remote Start button on the transmitter.* • Aftermarket remote. • Directed SmartStart application via your smartphone. & The parking lights will flash once to indicate the Parking lights flash x1 Press Remote vehicle is now in Pit Stop Mode.
  • Page 24 The application enables a “Cloud-Connected Car” like never before, providing 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet.

Table of Contents