Setting The Volume; Assigning Inputs /Outputs; Operation Of The Connection Extension Drm-884Iop; Renaming A Module - Monacor DRM-884DTM Instruction Manual

9.2 Setting the volume

w
Fig. 34 DRM-884VAP
To change the volume of an input or output:
1) Use the knob (x) to select the top row of the display (w) (icon
marks the current row) .
2) Press the knob . The icon changes to
3) Turn the knob to select the input or output to be adjusted .
4) Press the knob to confirm . The icon changes back to
5) Use the knob to select the third row . Press the knob to confirm .
The icon changes to .
6) Turn the knob to set the desired volume . The bar graph indicates
the current setting . The icon
channel . When the rectangle above the icon is black (
the signal level is too high and the signal is distorted . Reduce the
volume accordingly .
7) To make another setting, press the knob once again . The icon
changes back to .

9.3 Assigning inputs /outputs

Like in the view "Matrix" of the control program (
different inputs can be assigned to the outputs of the wall module .
1) Use the knob (x) to select the top row of the display (w) (icon
marks the current line) .
2) Press the knob . The icon changes to
3) Turn the knob to select the output to be adjusted .
4) Press the knob to confirm . The icon changes back to
5) Use the knob to select the second row . Press the knob to confirm .
A list of the inputs available appears .
6) Use the knob to select an input to be assigned and press the knob
to connect or disconnect . The icon
this input is routed to the output selected . If multiple inputs are
assigned to a single output, the signals of the inputs will be mixed .
7) To exit the list, select "Exit" at the bottom . Press the knob to con-
firm or wait for a few seconds until the list is exited automatically .
DRM-884VAP
VOLUME
x
.
.
= signal indicates the signal of the
= clip),
☞
chapter 7 .7),
.
.
means that the signal of
10 Operation of the Connection Extension
DRM-884IOP

10.1 Renaming a module

To change the name of a wall module DRM-884IOP, connect the
module to the master device DRM-884 . Start the control program in
the "Daisy Chain Network Mode", place a block for the module in
the device configuration, enter the device ID assigned and connect
the master device in the program (
the block of the module to call up the configuration window below:
Fig. 35 Configuration window for DRM-884IOP
The default device name is the type name "DRM-884IOP" . "Device
Name" can be used to change the name, for example to a name
specifying the place of installation .
To reset the name to the default name, use "Default" .

10.2 Matching the microphone input sensitivity

A B
i
MIC
2 1
3
k
Fig. 36 DRM-884IOP
The control (l) is used to match the input sensitivity of the microphone
input (k) to the microphone used . When the LED CLIP (n) for A / MIC
lights up, the signal level is too high and the sound may be distorted .
Turn back the control (l) accordingly or/and reduce the gain of the
input channel by means of the control program (

10.3 Activating / Deactivating the phantom power

Some microphones (e . g . condenser microphones) require phantom
power for operation . The switch (j) is used to activate a 48 V phantom
power at the input (k) (position ON) .
Caution: Only activate the phantom power when the audio sources connect-
ed expressly require phantom power . Phantom power may damage any audio
sources with unbalanced outputs . To prevent loud switching noise, only use the
switch when the master device DRM-884 has been switched off or when the
input channel has been muted .

10.4 Signal LEDs

The LEDs INPUT (m) indicate the input signals of this wall module,
the LEDs OUTPUT (n) indicate its output signals . The green LEDs SIG
indicate presence of a signal, the red LEDs CLIP indicate overload, i . e .
a signal level that is too high (signal distortion) .
☞
chapter 7 .2) . Then double-click
DRM-884IOP
j
CLIP CLIP CLIP CLIP
ON OFF
A/MIC A/MIC
B B
48 V
SIG SIG SIG SIG
m
INPUT INPUT
CLIP CLIP
A B
SIG SIG
0 50
n
l OUTPUT
☞
chapter 7 .6) .
45