Saving / Reloading All Presets; Copying Settings; View "System; Switching The Relays - Monacor DRM-884DTM Instruction Manual

7.12.4 Saving / Reloading all presets

To save all presets of the device to a file on the computer:
1) Click "Import All Presets" .
2) Confirm the security prompt for loading the presets . All presets will
be loaded from DRM-884 to the computer . The loading progress
is indicated under "Progress:" .
3) Confirm the security prompt for saving the presets to the computer .
4) Select the storage location and the file name .
To reload presets that have been saved to the computer:
1) Click "Export All Presets" .
2) Open the file containing the presets saved . All presets from the
file will be saved to DRM-884 . The progress is indicated under
"Progress:" .

7.12.5 Copying settings

The settings of an input channel can be copied to any other input
channels . Likewise, the settings of an output channel can be trans-
ferred to other output channels .
1) Select the channel whose settings are to be transferred to other
channels: Click the name of the channel [37] for inputs or [42] for
☞
outputs ( fig . 20 in chapter 7 .6) .
2) Call up the view "Save/Load/Copy" .
The name of the input or output selected can be found in the field
☞
"Copy from" fig . 27) .
3) Under "To Channels below:" (
which these settings are to be copied .
To select all channels, click "Select All" .
4) Click "Copy" to start copying .
Note: The setting "Microphone Sensitivity" [12] and the activation of phantom
power [10] in the input channels 1– 8 (fig . 20 in chapters 7 .6) will not be copied .

7.13 View "System"

Fig. 29 View "System"

7.13.1 Switching the relays

"Relay I" and "Relay II" are used to switch the two relays (13) . When
the button is green, the relay contact is closed . The relay status defined
here will be saved to a configuration .
42
☞
fig . 27), select the channels to

7.13.2 Resetting a configuration

"Restore Default Setting" is used to reset all parameters to the default
settings . The display (1) will show "Default" instead of a preset . The
presets saved to DRM-884 will be preserved .
"Restore to Factory Setting" is used to reset DRM-884 to the factory
settings . To preserve the presets that have been saved, save these
presets to the computer before resetting and reload the presets to
DRM-884 again after resetting (
Important: Use the function "Restore to Factory Setting" after firm-
ware update and when faults occur .

7.13.3 Renaming the device

In the category "Device Name", another name can be entered for
DMR-884, e . g . to distinguish between the devices when multiple
DRM-884 devices are used . To reset the name to "DRM-884", use
"Default" .
Note: When renaming the device, please note that there are restrictions regard-
ing special characters that can be shown on the display of the device (
in chapter 7 .6) .

7.13.4 Locking the device, changing the password

To lock the device against unauthorized operation, click "Lock Sys-
tem" . To unlock, the password is required . The default password is
"8888" .
To change the password, click "Password Setting" . The following
window will appear:
Fig. 30 Password Setting
1) Enter the current password in the field "Current Password" .
2) Enter the new password in the field "New Password" .
3) To confirm, enter the new password in the field "Confirm
Password" once again . Make sure to remember the password!
4) Click "Yes" to confirm or "Cancel" to cancel .

7.14 Exiting the program

To exit the program, go to the menu item "System  Exit" or close
the program window . If necessary, close the configuration window
previously .

8 Operation of the Microphone DRM-884RC

8.1 Presettings

To set up the microphone, connect the microphone to the master de-
vice DRM-884 . Start the control program in the "Daisy Chain Network
Mode", place a block for DRM-884RC in the device constellation, enter
the device ID assigned and connect the master device in the program
( ☞ chapter 7 .2) . Double-click the block DRM-884RC to call up the
configuration window below:
☞
chapter 7 .12 .4) .
☞ box