Chrysler Stratus RHD 1999 Electronic Service Manual page 862

JA
SPECIFICATIONS (Continued)
DESCRIPTION
Valve Timing – Exhaust Valve
Closes (ATDC) . . . . . . . . . . . . . . . . . . . . . . . . . . 8°
Opens (BBDC) . . . . . . . . . . . . . . . . . . . . . . . . . 52°
Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240°
Valve Timing
Valve Overlap . . . . . . . . . . . . . . . . . . . . . . . . . . 9°
Cylinder Head
Material . . . . . . . . . . . . . . . . . . . . Cast Aluminum
Gasket Thickness (Compressed) . . . . . . . 1.15 mm
Cylinder Head Valve Seat
Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45°
Runout (Max.) . . . . . . . . . . . 0.050 mm (0.002 in.)
Width (Finish) Intake and Exhaust . 0.9 - 1.3 mm
Guide Bore Diameter (Std) . . . . . 11.0 - 11.02 mm
Finish Guide Bore ID . . . . . . . . 5.975 - 6.000 mm
Valves
Face Angle . . . . . . . . . . . . . . . . . . . . 44-1/2° - 45°
Head Diameter Intake . . . . . . . . 34.67 - 34.93 mm
Head Diameter Exhaust . . . . . . 30.37 - 30.63 mm
Length–Intake (Overall) . . . . 112.76 - 113.32 mm
Length–Exhaust (Overall) . . . 109.59 - 110.09 mm
Valve Margin–Intake . . . . . . . . . 1.285 - 1.615 mm
Valve Margin–Exhaust . . . . . . . 0.985 - 1.315 mm
Valve Stem Tip Height–Intake . . . . . . . 48.04 mm
Valve Stem Tip Height–Exhaust . . . . . . 47.99 mm
Stem Diameter–Intake . . . . . . . 5.934 - 5.952 mm
Stem Diameter–Exhaust . . . . . . 5.906 - 5.924 mm
Stem-to-Guide Clearance–
Intake . . . . 0.048 - 0.066 mm (0.0018 - 0.0025 in.)
Stem-to-Guide Clearance–
Exhaust . . . . . . . . . . . . . . . . . 0.0736 - 0.094 mm
Max. Allowable Stem-to-Guide
Clearance–Intake and Exhaust . . . . . . 0.025 mm
SPECIFICATION
(0.045 in.)
(0.035 - 0.051 in.)
(0.4330 - 0.4338 in.)
(0.235 - 0.236 in.)
(1.364 - 1.375 in.)
(1.195 - 1.205 in.)
(4.439 - 4.461 in.)
(4.314 - 4.334 in.)
(0.050 - 0.063 in.)
(0.038 - 0.051 in.)
(1.891 in.)
(1.889 in.)
(0.234 - 0.234 in.)
(0.233 - 0.233 in.)
(0.0029 - 0.0037 in.)
(0.010 in.)
DESCRIPTION
Valve Springs
Free Length (Approx.) . . . . . . 48.4 mm (1.905 in.)
Spring Tension
(Valve Closed) . . . . . . . . . . 338 N
(75.98 lbs.
Spring Tension
(Valve Open) . . . . . . . . 607 N
Number of Coils . . . . . . . . . . . . . . . . . . . . . . . 7.82
Wire Diameter . . . . . . . . . . . . 3.86 mm (0.151 in.)
Installed Spring Height . . . . 38.00 mm (1.496 in.)
Oil Pump
Clearance Over Rotors (Max.) . . . . . . . . . 0.10 mm
Cover Out-of-Flat (Max.) . . . 0.025 mm (0.001 in.)
Inner Rotor Thickness (Min.) . 9.40 mm (0.370 in.)
Outer Rotor (Oil Pump)
Clearance (Max.) . . . . . . . . . . 0.39 mm (0.015 in.)
Diameter (Min.) . . . . . . . . . . 79.95 mm (3.148 in.)
Thickness (Min.) . . . . . . . . . . 9.40 mm (0.370 in.)
Tip Clearance Between Rotors (Max.) . . . 0.20 mm
Oil Pressure
At Curb Idle Speed * . . . . . . . . . . . 25 kPa (4 psi)
At 3000 rpm . . . . . . . . 170 - 550 kPa (25 - 80 psi)
CAUTION: * If pressure is ZERO at curb Idle, DO
NOT run engine at 3,000 rpm.
TORQUE CHART 2.4L
DESCRIPTION
Balance Shaft Carrier to Block
Bolts . . . . . . . . . . . . . . . . . . . . 54 N·m (40 ft. lbs.)
Balance Shaft Gear Cover
Double Ended Fastener . . . . 12 N·m (105 in. lbs.)
Balance Shaft Sprockets
Bolts . . . . . . . . . . . . . . . . . . . 28 N·m (250 in. lbs.)
Balance Shaft Chain Tensioner
Bolts . . . . . . . . . . . . . . . . . . . 12 N·m (105 in. lbs.)
Balance Shaft Carrier Cover
Fasteners . . . . . . . . . . . . . . . 12 N·m (105 in. lbs.)
Camshaft Sensor Pick Up
Bolts . . . . . . . . . . . . . . . . . . . . 27 N·m (20 ft. lbs.)
Camshaft Sprocket
Bolt . . . . . . . . . . . . . . . . . . . . 101 N·m (75 ft. lbs.)
Connecting Rod Cap
Bolts . . . . . . . . . 27 N·m (20 ft. lbs.) Plus 1/4 Turn
Crankshaft Main Bearing Cap/Bedplate
M8 Bedplate Bolts . . . . . . . . 34 N·m (250 in. lbs.)
Main Cap Bolts M11 . . . . . . . . 41 N·m (30 ft. lbs.)
2.4L ENGINE 9 - 107
SPECIFICATION
20 N 38.0 mm
4.5 lbs. @ 1.496 in.)
30 N @ 29.75 mm
(136 lbs. 7 @ 1.172 in.)
(0.004 in.)
(0.008 in.)
TORQUE
Plus 1/4 Turn