BONFIGLIOLI HDP Series Manual page 123

VP
input
GL
GR
input AD
n x h
2
250 000
500 000
750 000
1 000 000
1 250 000
2 500 000
3 750 000
5 000 000
VP
input
GL
GR
input AD
n x h
2
250 000
500 000
750 000
1 000 000
1 250 000
2 500 000
3 750 000
5 000 000
h: durata in ore riferita al cuscinetto dell'albero
lento.
Albero al quale sono riferiti i carichi radiali
ammissibili. Per gli alberi bisporgenti il cari-
co può essere applicato solo sull'estremità
così evidenziata. In caso diverso consultare
il Servizio Tecnico Bonfiglioli.
Carichi radiali ammissibili relativi ai cusci-
netti secondo variante HDB.
(—) Consultare il Servizio Tecnico Bonfiglioli
M = 15250 Nm
2
49.1 62.0 56.9
50.3 62.0 54.4
31.9 52.0 40.4
34.9 53.4 41.1
23.0 40.7 32.0
25.0 44.3 34.5
17.0 33.3 26.5
18.3 36.2 28.9
— 27.9 22.4
— 30.2 24.4
— 11.9 —
— — —
— — —
— — —
— — —
— — —
M = 15250 Nm
2
40.7 62.0 46.7
33.0 54.4 40.5
27.5 44.5 33.5
19.7 37.0 27.3
20.9 35.8 26.9
13.1 28.3 20.7
16.4 30.3 22.7
— 22.7 16.5
— 26.3 19.7
— 18.7 13.5
— — —
— — —
— — —
— — —
— — —
— — —
h: expected lifetime [hours] for bearing of the
output shaft.
Shaft the rated overhung load is applicable to.
For double extended shaft the load is only ap-
plicable to the extension highlighted Should
this not be the case consult Bonfiglioli's Tech-
nical Service.
Rated overhung loads relevant to rein-
forced bearings type HDB.
(—) Contact the Bonfiglioli Technical Service.
HDP 90
Rn [kN]
2
M = 12200 Nm M
2
62.0 61.5
62.0 57.1
60.7 45.7
57.9 43.8
49.9 37.5
49.2 37.3
42.8 32.1
43.7 33.1
37.6 28.3
39.6 30.1
23.3 17.5
25.2 19.0
15.6 —
16.7 —
— —
— —
HDP 90
Rn [kN]
2
M = 12200 Nm M
2
62.0 50.7
62.0 45.6
50.8 37.5
44.7 32.3
42.1 30.9
36.0 25.7
36.5 26.7
30.5 21.5
32.5 23.7
26.5 18.5
21.7 15.5
15.7 —
14.8 —
— —
— —
— —
LP
= 10150 Nm M
2 2
62.0 63.7
62.0 60.4
62.0 50.5
60.8 47.2
55.5 43.9
52.2 40.6
48.6 38.7
46.6 36.4
43.7 35.0
42.7 33.4
29.8 24.7
31.9 25.2
22.8 19.5
24.7 21.2
18.1 16.1
19.6 17.6
LP
= 10150 Nm M
2 2
62.0 55.7
62.0 51.8
54.9 42.4
49.9 38.6
46.3 35.9
41.3 32.0
40.7 31.7
35.7 27.8
36.8 28.7
33.3 24.8
25.9 20.5
20.9 16.6
20.6 16.4
15.5 12.6
17.1 —
— —
h: Lebensdauer in Stunden für das Lager der
Abtriebswelle.
Welle, auf die sich die zulässigen Radialkräfte
beziehen. Für die Wellen mit zwei Wellenzap-
fen kann die Kraft nur auf das so gekenn-
zeichnete Wellenende ausgeübt werden. An-
dernfalls mit dem technischen Kundendienst
von Bonfiglioli Rücksprache halten.
Zulässige Radialkräfte der Lager gemäß
Variante HDB.
(—) Bitte wenden Sie sich an den technischen
Kundendienst von Bonfiglioli.
H S
= 7600 Nm
—
62.0
62.0
62.0
59.3
55.9
53.8
50.3
49.8
46.4
37.2
35.6
30.6
30.2
26.2
26.8
H S
= 7600 Nm
62.0
62.0
60.2
56.4
51.5
47.7
45.9
42.2
41.9
38.2
31.2
27.4
25.8
22.0
22.4
18.6
121