BONFIGLIOLI HDP Series Manual page 122

VP
input GL
GR
input AD
n x h
2
250 000
500 000
750 000
1 000 000
1 250 000
2 500 000
3 750 000
5 000 000
VP
input GL
GR
input AD
n x h
2
250 000
500 000
750 000
1 000 000
1 250 000
2 500 000
3 750 000
5 000 000
h: durata in ore riferita al cuscinetto dell'albero
lento.
Albero al quale sono riferiti i carichi radiali
ammissibili. Per gli alberi bisporgenti il cari-
co può essere applicato solo sull'estremità
così evidenziata. In caso diverso consultare
il Servizio Tecnico Bonfiglioli.
Carichi radiali ammissibili relativi ai cusci-
netti secondo variante HDB.
(—) Consultare il Servizio Tecnico Bonfiglioli
120
M = 11450 Nm
2
39.3 46.0 43.7
37.1 46.0 40.3
26.0 41.7 32.3
27.1 39.9 30.3
16.7 33.5 25.8
20.0 33.5 25.4
10.4 28.1 21.5
14.8 29.4 22.2
— 24.2 17.8
— 25.7 19.5
— 10.1 —
— 13.0 —
— — —
— — —
— — —
— — —
M = 11450 Nm
2
27.5 43.6 32.6
23.3 39.4 29.2
17.5 30.7 22.7
13.3 26.5 19.3
12.6 24.3 17.7
— 20.1 14.4
— 20.2 14.5
— 16.1 11.2
— 17.3 12.3
— 13.1 —
— 9.4 —
— — —
— — —
— — —
— — —
— — —
h: expected lifetime [hours] for bearing of the
output shaft.
Shaft the rated overhung load is applicable to.
For double extended shaft the load is only ap-
plicable to the extension highlighted Should
this not be the case consult Bonfiglioli's Tech-
nical Service.
Rated overhung loads relevant to rein-
forced bearings type HDB.
(—) Contact the Bonfiglioli Technical Service.
HDP 80
Rn [kN]
2
M = 9150 Nm M
2
46.0 45.3
46.0 42.4
46.0 35.3
43.1 32.5
39.3 29.8
36.7 27.5
34.2 25.8
32.6 24.4
30.5 22.8
29.7 22.1
20.0 13.5
21.3 15.2
13.8 —
15.3 —
— —
11.2 —
HDP 80
Rn [kN]
2
M = 9150 Nm M
2
46.0 36.1
45.2 33.3
35.7 26.1
32.4 23.3
29.3 21.2
26.0 18.3
25.3 18.0
21.9 15.2
22.3 15.7
19.0 13.0
14.4 —
11.0 —
10.4 —
— —
— —
— —
LP
= 7600 Nm M
2 2
46.0 47.2
46.0 45.1
46.0 37.2
45.2 35.1
41.6 32.3
38.8 30.2
37.6 29.1
34.7 27.0
34.3 26.9
31.8 24.8
24.3 19.7
23.9 18.6
19.1 15.7
19.9 15.6
15.8 13.1
16.8 13.6
LP
= 7600 Nm M
2 2
46.0 40.3
46.0 38.2
39.1 30.3
36.3 28.2
32.7 25.4
29.9 23.3
28.6 22.2
25.8 20.2
25.7 20.0
22.9 17.9
17.8 13.8
15.0 11.8
13.8 —
11.0 —
11.3 —
— —
h: Lebensdauer in Stunden für das Lager der
Abtriebswelle.
Welle, auf die sich die zulässigen Radialkräfte
beziehen. Für die Wellen mit zwei Wellenzap-
fen kann die Kraft nur auf das so gekenn-
zeichnete Wellenende ausgeübt werden. An-
dernfalls mit dem technischen Kundendienst
von Bonfiglioli Rücksprache halten.
Zulässige Radialkräfte der Lager gemäß
Variante HDB.
(—) Bitte wenden Sie sich an den technischen
Kundendienst von Bonfiglioli.
H S
= 5700 Nm
46.0
46.0
46.0
46.0
43.5
41.4
39.5
37.3
36.5
34.4
28.6
26.5
24.1
22.5
21.0
20.0
H S
= 5700 Nm
46.0
46.0
43.2
41.1
36.8
34.7
32.8
30.7
29.8
27.7
21.9
19.8
18.0
15.9
15.4
13.4