2N IP Base Installation Manual

2N IP Base Installation Manual

Door entry ip intercom
Hide thumbs Also See for IP Base:

Advertisement

®
2N IP Base
Door Entry IP Intercom
Installation Manual
Version:
2.11
www.2n.cz

Advertisement

Table of Contents
loading

Summary of Contents for 2N IP Base

  • Page 1 ® 2N IP Base Door Entry IP Intercom Installation Manual Version: 2.11 www.2n.cz...
  • Page 2 2N TELEKOMUNIKACE a.s. administers the FAQ database to help you quickly find information and to answer your questions about 2N products and services. On www. faq.2n.cz you can find information regarding products adjustment and instructions for optimum use and procedures „What to do if...".
  • Page 3: Table Of Contents

    3.2 Intercom Control as Viewed by External User 3.3 Intercom Control as Viewed by Internal User 3.4 Maintenance 3.5 Downloads 4. Technical Parameters 5. Supplementary Information 5.1 Troubleshooting 5.2 Directives, Laws and Regulations 5.3 General Instructions and Cautions 2N TELEKOMUNIKACE a.s., www.2n.cz 3/66...
  • Page 4: Product Overview

    1. Product Overview Here is what you can find in this section: 1.1 Components and Associated Products 1.2 Terms and Symbols 2N TELEKOMUNIKACE a.s., www.2n.cz 4/66...
  • Page 5 The intercom can be supplied from a 12 V DC power source, or using a PoE switch. ® Use your PC with any internet browser to configure IP Base or apply the ® Access Commander to configure extensive installations of multiple intercoms. 2N TELEKOMUNIKACE a.s., www.2n.cz 5/66...
  • Page 6 Configuration using web interface or dedicated PC application VoIP standard SIP 2.0 support 1999 Phone Book positions 20 user time profiles Video codecs (H.263, H.263+, H.264, MJPEG) Audio codecs (G.711, G.722) NTP client for time synchronisation 2N TELEKOMUNIKACE a.s., www.2n.cz 6/66...
  • Page 7: Components And Associated Products

    Mounting backplate 2N Part No. 9156020 ® IP Base – mounting backplate Axis Part No. 01360-001 ® Mounting backplate for main unit 2N IP Base Optional, recommended for mounting on uneven surfaces (inequalities bigger than 2mm) 2N TELEKOMUNIKACE a.s., www.2n.cz 7/66...
  • Page 8 ® IP Base is designed for outdoor use and requires no additional roof. Expansion modules 2N Part No. 9156030 ® IP Base – RFID Card Reader, 125 kHz Axis Part No. 01358-001 The card reader module provides you with access control via contactless cards or keyfobs.
  • Page 9 . On the panel’s display not only can you find out who is at the door, but also start a conversation with the visitor, open the lock or turn on the light in the entrance hall. 2N TELEKOMUNIKACE a.s., www.2n.cz 9/66...
  • Page 10 Part number: ® Indoor Touch desk stand white 91378382W, 01426-001 2N TELEKOMUNIKACE a.s., www.2n.cz 10/66...
  • Page 11 VoIP Phones 2N Part No. 91378357 Grandstream GXV3240 VoIP video telephone Axis Part No. 01422-001 GXV3240 is the successor to the popular GXV3140 model, which allows comfortable video calls in the IP network. Touchscreen and keyboard control. 2N Part No. 91378358 Grandstream GXV3275 VoIP telephone Axis Part No.
  • Page 12 BEFO 11211MB with mechanical blocking 12 V / 230 mA DC low consumption Enables mechanically close or open the lock. When opened, the lock is open all the time. When closed, it behaves as standart electrical lock. 2N TELEKOMUNIKACE a.s., www.2n.cz 12/66...
  • Page 13 When electricity is interrupted, the lock is opened. It contains a built-in contact to indicate whether the door is open or closed. FAQ: Electric locks – Difference between locks in 2N IP intercoms accesories Power Supply 2N TELEKOMUNIKACE a.s., www.2n.cz...
  • Page 14 Part No. 91341481E Stabilised 12 V / 2 A power supply needs to be used when no PoE is available. Part No. 932928 For external power supply of the lock with 12 V AC voltage. 2N TELEKOMUNIKACE a.s., www.2n.cz 14/66...
  • Page 15 (2 wires) from your original door bell or door intercom to connect any IP device. You don’t have to ® configure anything, and you only need one 2N 2Wire unit at each end of the cable and a power source connected to at least one of these units.
  • Page 16 External RFID card reader for connection to PC using a USB interface. Suitable for system administration and adding 13.56 MHz, 125 kHz cards and Android platform devices supporting NFC/HCE using 2N IP intercom ® web interface or the 2N Access Commander application.
  • Page 17 ISO/IEC 14443B CEPAS, HID iCLASS (CSN or PAC ID) JIS X 6319 Felica ISO/IEC 18092 SmartPhone with NFC/HCE ® support, since Android version 4.3 (2N Mobile app required) EMarine 2N Part No. 9134173 Mifare Classic 1k RFID card, 13.56 MHz Axis Part No.
  • Page 18 Suitable for system management and the addition of Axis Part No. 01399- ® EM41xx cards via the PC application, Access Commander 2N Part No. 9134165E RFID card, type EM4100, 125 kHz Axis Part No. 01395- 2N Part No. 9134166E RFID fob, type EM4100, 125 kHz Axis Part No.
  • Page 19 External switches 2N Part No. 9159010 ® Security Relay Axis Part No. 01386- A handy add-on that significantly enhances door entry security as it prevents tampering with the intercom and forced opening of the lock. To be installed between intercom and lock, powered by the intercom.
  • Page 20 Part No. 9159013 Exit button A button for connection to a logic input for opening a door inside a building. 2N Part No. 9159012 Magnetic door contact Axis Part No. 01388-001 Set for installation on a door, enabling the status of door opening to be ascertained.
  • Page 21 2N Part No. Enhanced Security 9137908 Axis Part No. 01379-001 2N Part No. Gold 9137909 Axis Part No. 01380-001 2N Part No. InformaCast 9137910 Axis Part No. 01381-001 2N Part No. 9137915 Axis Part No. 01382-001 2N TELEKOMUNIKACE a.s., www.2n.cz 21/66...
  • Page 22 Refer to the Configuration Manual for 2N IP intercoms, Subs. 3.2 Function Licensing for details. For more accessories and particular advice please contact your local distributor of 2N products. 2N TELEKOMUNIKACE a.s., www.2n.cz 22/66...
  • Page 23: Terms And Symbols

    Warning Always abide by this information to prevent damage to the device. Caution Important information for system functionality. Useful information for quick and efficient functionality. Note Routines or advice for efficient use of the device. 2N TELEKOMUNIKACE a.s., www.2n.cz 23/66...
  • Page 24: Description And Installation

    2. Description and Installation Here is what you can find in this section: 2.1 Before You Start 2.2 Mechanical Installation 2.3 Electric Installation 2.4 Extending Module Connection 2.5 Completion 2N TELEKOMUNIKACE a.s., www.2n.cz 24/66...
  • Page 25: Before You Start

    Before you start please check whether the contents of the package of your new ® IP Base complies with the following list: ® IP Base Manual Films for labels Double-ended wrench – Torx Double-button Screws and dowels Metal pads 2N TELEKOMUNIKACE a.s., www.2n.cz 25/66...
  • Page 26 2N TELEKOMUNIKACE a.s., www.2n.cz 26/66...
  • Page 27: Mechanical Installation

    Fit the device to the backplate. You can use a drilling template; download here Plug in the cables, check the functionality of the device. Replace the blank module and attach the frame. The figures below show frame demounting and position of the mounting screws. 2N TELEKOMUNIKACE a.s., www.2n.cz 27/66...
  • Page 28 Frame Demounting. First use the torx handle enclosed to remove the screw that fits ® the frame to the IP Base structure. ® Position of Mounting Screws on 2N IP Base 2N TELEKOMUNIKACE a.s., www.2n.cz 28/66...
  • Page 29 The device is intended for surface mounting, for this type of installation the device itself is sufficient. A mounting backplate can be used ( Part. No. 9156020 ) for uneven surfaces and easier installation. For mounting backplate installation, follow the mounting backplate instructions. 2N TELEKOMUNIKACE a.s., www.2n.cz 29/66...
  • Page 30 Make sure that the surface mounting place is perfectly flat with the maximum inequality of 2 mm (e.g. desk materials, glass, cut stone etc.). If the place is not flat, use mounting backplate Part No. 9156020 or equal the wall surface. 2N TELEKOMUNIKACE a.s., www.2n.cz 30/66...
  • Page 31 2N TELEKOMUNIKACE a.s., www.2n.cz 31/66...
  • Page 32: Electric Installation

    2.3 Electric Installation ® Static IP Address Setting This subsection describes how to connect the 2N IP Base main unit to the power supply and LAN and how to connect other elements. Connection of RFID reader modules is contained in section 2.4 Extending Module...
  • Page 33 LED indicators (red – device state / green – eth. link up / yellow – LAN activity) Output wiring diagram for Relay terminals The electric lock is opened by power supply connection. The magnetic lock is opened by power supply disconnection. 2N TELEKOMUNIKACE a.s., www.2n.cz 33/66...
  • Page 34 In the latter case, use an external lock supply. In any case, you are recommended to use low-consumption locks and keep the limits mentioned above. 2N TELEKOMUNIKACE a.s., www.2n.cz 34/66...
  • Page 35 PoE 802.3af (Class 0–12,95 W) technology and can be fed directly from the LAN via the compatible network elements. If your LAN does ® not support this technology, insert a PoE injector, Part No. 91378100, between 2N ® Base and the nearest network element.
  • Page 36 Wait until the red LED goes off (approx. 5 s). Wait until the green LED goes off and the red LED comes on again (approx. 5 s). Wait until the red LED goes off (another 5 s). Release the RESET button. 2N TELEKOMUNIKACE a.s., www.2n.cz 36/66...
  • Page 37 Press and hold the REST button. Wait until the red and green LEDs on the device come on simultaneously (approx. 20 s). Wait until the red LED goes off (approx. 5 s). Release the RESET button. 2N TELEKOMUNIKACE a.s., www.2n.cz 37/66...
  • Page 38 Wait until the green LED goes off and the red LED comes on again (another 5 s). Release the RESET button. Device Restart Press the RESET button shortly (< 1 s) to restart the system without changing configuration. 2N TELEKOMUNIKACE a.s., www.2n.cz 38/66...
  • Page 39: Extending Module Connection

    , are connected via connector X12, the position of this connector is shown in Fig. Before connecting RFID card reader it is suitable to ® disconnect IP Base from the power supply. Only one module can be connected at a time. 2N TELEKOMUNIKACE a.s., www.2n.cz 39/66...
  • Page 40 How to install modules: 1) On the picture there is a highlighted connector X12. This connector is designed to connect the module to the main unit. Insert the module of card reader into the shown connector. 2N TELEKOMUNIKACE a.s., www.2n.cz 40/66...
  • Page 41 3) As the last, it is necessary to fix the module using tabs built into the structure of ® IP Base . This tab is highlighted in the following picture by the red rectangle. 2N TELEKOMUNIKACE a.s., www.2n.cz 41/66...
  • Page 42 EM4100, EM4102, HID Proximity RFID Card Reader 13.56 MHz ® The 13.56 MHz RFID Card Reader ( Part No. 9156031) is one of the 2N IP Base intercom elements and is used for reading RFID card Ids in the 13.56 MHz band.
  • Page 43 To the intercom relay output with a 12 V DC serial external power supply. ® Connect the electric lock to the Security Relay output as follows: To the switched output. To the passive output in series with the external power supply. 2N TELEKOMUNIKACE a.s., www.2n.cz 43/66...
  • Page 44 (the green LED is blinking). Caution In case of resetting the factory default settings on a device with a ® version of firmware 2.18 or higher it is necessary to reprogram the 2N Security Relay using the instructions above. 2N TELEKOMUNIKACE a.s., www.2n.cz...
  • Page 45 ® FAQ: 2N Security Relay – what it is and how to use it with 2N IP intercom? Video Tutorial: Door 2N IP intercoms – Security Relay Connection: 2N TELEKOMUNIKACE a.s., www.2n.cz 45/66...
  • Page 46: Completion

    Nametag Inserting/Replacing: Remove the frame. Remove the button cover using the clips placed on the shorter sides of the cover. Remove the used nametag and insert a new one. Replace the button cover. Replace the frame. 2N TELEKOMUNIKACE a.s., www.2n.cz 46/66...
  • Page 47: Function And Use

    3. Function and Use ® This section describes the basic and extending functions of the the 2N IP Base product. Here is what you can find in this section: 3.1 Configuration 3.2 Intercom Control as Viewed by External User 3.3 Intercom Control as Viewed by Internal User 3.4 Maintenance...
  • Page 48: Configuration

    If your device remains inaccessible (you have forgotten the IP address, the network configuration has changed, etc.), you can change the network configuration using the device buttons. ® Refer to the Configuration manual for 2N IP intercoms for the IP Base configuration details. 2N TELEKOMUNIKACE a.s., www.2n.cz...
  • Page 49 If the address is 0.0.0.0, it means that the intercom has not obtained the IP address from the DHCP server Note Be sure to press the button sequence within thirty seconds after the sound signal for security reasons. Up to 2 s intervals are allowed between the presses. 2N TELEKOMUNIKACE a.s., www.2n.cz 49/66...
  • Page 50 Press the quick dial button on the main unit 15 times. Switching is signalled with the sound signal Wait until the device is restarted automatically. Upon restart, the static IP address mode will be switched to the dynamic IP address mode and vice versa. 2N TELEKOMUNIKACE a.s., www.2n.cz 50/66...
  • Page 51 IP address: 192.168.1.100 Network mask: 255.255.255.0 Default gateway: 192.168.1. Note Be sure to press the button sequence within thirty seconds after the sound signal for security reasons. Up to 2 s intervals are allowed between the presses. 2N TELEKOMUNIKACE a.s., www.2n.cz 51/66...
  • Page 52: Intercom Control As Viewed By External User

    Repeated pressing of one and the same speed dial button during call setup may initiate call termination, or call termination plus dialling the next telephone number of the called subscriber, or may be assigned no function. 2N TELEKOMUNIKACE a.s., www.2n.cz 52/66...
  • Page 53: Intercom Control As Viewed By Internal User

    Configuration Manual). Press # on your phone anytime to extend the call time. The automatic call termination is signalled with a short beep 10 s before the call end. Calling to 2N ® IP Base ® IP Base allows you to answer incoming calls.
  • Page 54: Maintenance

    Clean the device in dry weather in order to make waste water evaporate quickly. Cleaning wipes for IT equipment are suitable. Warning Prevent water from getting inside the intercom. Do not use alcohol-based cleaners. Avoid peroxide-based cleaners. 2N TELEKOMUNIKACE a.s., www.2n.cz 54/66...
  • Page 55: Downloads

    3.5 Downloads Templates Nameplates Drilling Template Software ® USB driver ® IP Eye ® Network Scanner 2N TELEKOMUNIKACE a.s., www.2n.cz 55/66...
  • Page 56: Technical Parameters

    Sound pressure level (SPL max) : 78 dB (for 1 kHz, distance 1 m) Volume control: Adjustable with automatic adaptive mode Full duplex: Yes (AEC) Speech transmission index (STI): 0.80 Audio stream Protocols: Codecs: G.711, G.729, G.722, L16/16 kHz 2N TELEKOMUNIKACE a.s., www.2n.cz 56/66...
  • Page 57 Sensor sensitivity without IR light: 0,1 Lux ± 20 % Focal length: 2.3 mm Video stream Protocols: RTP / RTSP / HTTP Codecs: H.263, H.263+, H.264, MPEG-4, M-JPEG IP camera function: yes, ONVIF v2.4 profile S compatible 2N TELEKOMUNIKACE a.s., www.2n.cz 57/66...
  • Page 58 NO/NC contact, up to 30 V / 1 A AC/DC Active switch output: 8 up to 12 V DC depending on power supply (PoE: 10 V; adaptor: power supply voltage minus 2 V), max 600 mA 2N TELEKOMUNIKACE a.s., www.2n.cz 58/66...
  • Page 59 Working relative humidity: 10 % – 95 % (non-condensing) Storing temperature: −40 °C – 70 °C Dimensions: 229 (W) x 109 (H) x 31 (H) Weight: Max net weight: 1 kg Covering level: IK 7 IP 65 2N TELEKOMUNIKACE a.s., www.2n.cz 59/66...
  • Page 60: Supplementary Information

    5. Supplementary Information Here is what you can find in this section: 5.1 Troubleshooting 5.2 Directives, Laws and Regulations 5.3 General Instructions and Cautions 2N TELEKOMUNIKACE a.s., www.2n.cz 60/66...
  • Page 61: Troubleshooting

    5.1 Troubleshooting For the most frequently asked questions refer to faq.2n.cz 2N TELEKOMUNIKACE a.s., www.2n.cz 61/66...
  • Page 62: Directives, Laws And Regulations

    Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help. 2N TELEKOMUNIKACE a.s., www.2n.cz 62/66...
  • Page 63 2N TELEKOMUNIKACE a. s. is not liable neither for any limitation of such a product’s functionality, nor for any damage, loss or injury relating to such a potential limitation of functionality.
  • Page 64: General Instructions And Cautions

    The consumer shall, at its own expense, obtain software protection of the product. The manufacturer shall not be held liable and responsible for any damage incurred as a result of the use of deficient or substandard security software. 2N TELEKOMUNIKACE a.s., www.2n.cz 64/66...
  • Page 65 Make sure that the devices to be disposed of are complete. Do not throw battery packs into fire. Battery packs may not be taken into parts or short-circuited either. 2N TELEKOMUNIKACE a.s., www.2n.cz 65/66...
  • Page 66 2N TELEKOMUNIKACE a.s. Modřanská 621, 143 01 Prague 4, Czech Republic Phone: +420 261 301 500, Fax: +420 261 301 599 E-mail: sales@2n.cz Web: www.2n.cz v2.11 2N TELEKOMUNIKACE a.s., www.2n.cz 66/66...

Table of Contents