Configuring Of Closed-Loop Control; P595 Source For Actual Value Of "Overspeed Signal”; P597 Source For Actual Value Of “Nset = Nact Signal 2”; P600 Source For Gating Unit Input (Armature) - Siemens 6RA70 Series Instructions Manual

PNU Description
P592 Source for actual value of "n < n comp. signal"
*
n < n comp. signal:
Selection of connector to be injected as input quantity (n) for the n < n comp.
(G187)
signal.
0 = connector K0000
1 = connector K0001
etc.
P593 Source for actual value of "n < n min signal"
*
n < n min signal:
Selection of connector to be injected as input quantity (n) for the n < n min
(G187)
signal.
0 = connector K0000
1 = connector K0001
etc.
P594 Source for input quantity of "Polarity signal"
*
Polarity signal of speed setpoint:
Selection of connector to be injected as input quantity "n set " for the polarity
(G188)
signal of the speed setpoint.
0 = connector K0000
1 = connector K0001
etc.
P595 Source for actual value of "Overspeed signal"
*
Overspeed signal:
Selection of connector to be injected as input quantity "n act " for the
(G188)
overspeed signal.
0 = connector K0000
1 = connector K0001
etc.
P596 Source for setpoint of "nset = nact signal 2"
*
Setpoint/actual value deviation signal:
Selection of connector to be injected as input quantity "n set " for the
(G187)
setpoint/actual value deviation signal.
0 = connector K0000
1 = connector K0001
etc.
P597 Source for actual value of "nset = nact signal 2"
*
Setpoint/actual value deviation signal:
Selection of connector to be injected as input quantity "n act " for the
(G187)
setpoint/actual value deviation signal.
0 = connector K0000
1 = connector K0001
etc.

10.34 Configuring of closed-loop control

Setting values for configuring of torque shell
P600 Source for gating unit input (armature)
*
i001 to i004:
(G163) Selects which connectors are applied as the gating unit input
(armature). All four values are added.
Settings:
0 = connector K0000
1 = connector K0001
etc.
SIEMENS Energy & Automation
SIMOREG DC Master Base Drive Panel Operating Instructions
Value range
[Unit]
Steps
All connector
numbers
1
All connector
numbers
1
All connector
numbers
1
All connector
numbers
1
[SW 1.9 and later] All connector
numbers
1
[SW 1.9 and later] All connector
numbers
1
All connector
numbers
1
No. indices See
Factory Change
setting (Access /
Type Status)
Ind: None P052 = 3
FS=167 P051 = 40
Type: L2 Offline
Ind: None P052 = 3
FS=167 P051 = 40
Type: L2 Offline
Ind: None P052 = 3
FS=170 P051 = 40
Type: L2 Offline
Ind: None P052 = 3
FS=167 P051 = 40
Type: L2 Offline
Ind: None P052 = 3
FS=174 P051 = 40
Type: L2 off-line
Ind: None P052 = 3
FS=167 P051 = 40
Type: L2 off-line
Ind: 4 P052 = 3
FS= P051 = 40
i001: 102 off-line
i002: 0
i003: 0
i004: 0
Typ: L2
10-59